Message-ID: <bb1334bf-42fe-c6a9-c843-87efeb77c101@loongson.cn>
Date:   Mon, 14 Aug 2023 20:22:06 +0800
From:   Yinbo Zhu <zhuyinbo@...ngson.cn>
To:     "Rafael J . Wysocki" <rafael@...nel.org>,
        Daniel Lezcano <daniel.lezcano@...aro.org>,
        Amit Kucheria <amitk@...nel.org>,
        Zhang Rui <rui.zhang@...el.com>, linux-pm@...r.kernel.org,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Cc:     Jianmin Lv <lvjianmin@...ngson.cn>, wanghongliang@...ngson.cn,
        loongson-kernel@...ts.loongnix.cn,
        zhanghongchen <zhanghongchen@...ngson.cn>, zhuyinbo@...ngson.cn
Subject: Re: [PATCH v15 1/2] thermal: loongson-2: add thermal management
 support



Friendly ping ?


在 2023/6/20 上午9:29, Yinbo Zhu 写道:
> This patch adds the support for Loongson-2 thermal sensor controller,
> which can support maximum four sensor selectors that corresponding to four
> sets of thermal control registers and one set of sampling register. The
> sensor selector can selector a speific thermal sensor as temperature input.
> The sampling register is used to obtain the temperature in real time, the
> control register GATE field is used to set the threshold of high or low
> temperature, when the input temperature is higher than the high temperature
> threshold or lower than the low temperature threshold, an interrupt will
> occur.
> 
> Signed-off-by: zhanghongchen <zhanghongchen@...ngson.cn>
> Signed-off-by: Yinbo Zhu <zhuyinbo@...ngson.cn>
> ---
> Change in v15:
> 		1. Remove the unused head file.
> 		2. Remove the invalid conditions that such as (low > high).
> 		3. Use the clamp() to replace max() and min().
> 		4. Use the macros to replace some constant.
> 		5. Use the struct data point as data field of of_device_id.
> 		6. Use the thermal_sensor_sel to replace the sensor id.
> 		7. Use the thermal_zone_device_priv to replace tz->devdata.
> 		8. Reword the commit log information.
> Change in v14:
> 		1. Add back depends on COMPILE_TEST.
> 		2. The implementation of devm_thermal_add_hwmon_sysfs has changed in
> 		   recent community code that cause compile fail issue and this verison
> 		   add a dev args in devm_thermal_add_hwmon_sysfs to fix compile issue.
> Change in v13:
> 		1. Add a description about that how works the sensor.
> 		2. Drop the COMPILE_TEST.
> 		3. Rework the help prograph in LOONGSON2_THERMAL Kconfig.
> 		4. Drop the 'tzd' 'irq' and 'pdev' element in loongson2_thermal_data.
> 		5. Drop the reset of variable in loongson2_thermal_set.
> 		6. Drop the function loongson2_thermal_get_sensor_id.
> 		7. Drop the function loongson2_thermal_alarm_irq.
> 		8. Rework the devm_thermal_of_zone_register.
> 		9. Pass 'tzd' instead of 'data' in devm_request_threaded_irq.
> 		10. Drop the "data->tzd->tzp->no_hwmon = false".
> 		11. Drop the loongson2_thermal_remove.
> 		12. Add the sensor id in the of_device_id data field.
> 		13. Drop the save and restore function.
> Change in v12:
> 		1. Fixup it about min and max.
> 		2. Use dev_err_probe replace dev_err in devm_request_threaded_irq context.
> Change in v11:
> 		1. Add min() and max() to replace related code in function
> 		   loongson2_thermal_set.
> 		2. Add dev_err_probe to to replace related code for function
> 		   return value use devm_thermal_of_zone_register.
> 		3. Replace thermal_add_hwmon_sysfs with devm_thermal_add_hwmon_sysfs
> 		   and use dev_warn replace dev_err in this context.
> Change in v10:
> 		1. Add all history change log information.
> Change in v9:
> 		1. Switch new API that use devm_thermal_of_zone_register
> 		   to replace previous interfaces.
> 		2. Add depend on LOONGARCH || COMPILE_TEST.
> Change in v8:
>                  1. Replace string loongson2/Loongson2/LOONGSON2 with loongson-2/
>                     Loongson-2/LOONGSON-2 in Kconfig and commit log and MAINTAINERS
> 		   files.
> Change in v7:
> 		1. Split the modification of patch 3 and merge it into this patch.
> 		2. Remove the unless code annotation to fix the compile warning
> 		   when compile C code with W=1.
> Change in v6:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v5:
> 		1. NO change, but other patch in this series of patches set has
> 		   changes.
> Change in v4:
> 		1. Fixup the compatible.
> Change in v3:
> 		1. Add a function to gain sensor id an remove dts id.
> Change in v2:
> 		1. Remove error msg printing when addr ioremap has error.
> 		2. Make loongson2 thermal driver was built-in by default.
> 		3. Replace ls2k with loongson2.
> 		4. Remove CONFIG_PM_SLEEP and set pm function type was
> 		   __maybe_unused.
> 
>   MAINTAINERS                         |   7 ++
>   drivers/thermal/Kconfig             |  12 ++
>   drivers/thermal/Makefile            |   1 +
>   drivers/thermal/loongson2_thermal.c | 170 ++++++++++++++++++++++++++++
>   4 files changed, 190 insertions(+)
>   create mode 100644 drivers/thermal/loongson2_thermal.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7a91f14cad2e..f9277fa2a728 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12198,6 +12198,13 @@ S:	Maintained
>   F:	Documentation/devicetree/bindings/pinctrl/loongson,ls2k-pinctrl.yaml
>   F:	drivers/pinctrl/pinctrl-loongson2.c
>   
> +LOONGSON-2 SOC SERIES THERMAL DRIVER
> +M:	zhanghongchen <zhanghongchen@...ngson.cn>
> +M:	Yinbo Zhu <zhuyinbo@...ngson.cn>
> +L:	linux-pm@...r.kernel.org
> +S:	Maintained
> +F:	drivers/thermal/loongson2_thermal.c
> +
>   LOONGSON GPIO DRIVER
>   M:	Yinbo Zhu <zhuyinbo@...ngson.cn>
>   L:	linux-gpio@...r.kernel.org
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 4cd7ab707315..c4de94e972f4 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -502,4 +502,16 @@ config KHADAS_MCU_FAN_THERMAL
>   	  If you say yes here you get support for the FAN controlled
>   	  by the Microcontroller found on the Khadas VIM boards.
>   
> +config LOONGSON2_THERMAL
> +	tristate "Loongson-2 SoC series thermal driver"
> +	depends on LOONGARCH || COMPILE_TEST
> +	depends on OF
> +	help
> +	  Support for Thermal driver found on Loongson-2 SoC series platforms.
> +	  The thermal driver realizes get_temp and set_trips function, which
> +	  are used to obtain the temperature of the current node and set the
> +	  temperature range to trigger the interrupt. When the input temperature
> +	  is higher than the high temperature threshold or lower than the low
> +	  temperature threshold, the interrupt will occur.
> +
>   endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 058664bc3ec0..c934cab309ae 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -63,3 +63,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
>   obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
>   obj-$(CONFIG_SPRD_THERMAL)	+= sprd_thermal.o
>   obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL)	+= khadas_mcu_fan.o
> +obj-$(CONFIG_LOONGSON2_THERMAL)	+= loongson2_thermal.o
> diff --git a/drivers/thermal/loongson2_thermal.c b/drivers/thermal/loongson2_thermal.c
> new file mode 100644
> index 000000000000..2be8e0f5fea3
> --- /dev/null
> +++ b/drivers/thermal/loongson2_thermal.c
> @@ -0,0 +1,170 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Author: zhanghongchen <zhanghongchen@...ngson.cn>
> + *         Yinbo Zhu <zhuyinbo@...ngson.cn>
> + * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/minmax.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/thermal.h>
> +#include <linux/units.h>
> +#include "thermal_hwmon.h"
> +
> +#define LOONGSON2_MAX_SENSOR_SEL_NUM			3
> +
> +#define LOONGSON2_THSENS_CTRL_HI_REG			0x0
> +#define LOONGSON2_THSENS_CTRL_LOW_REG			0x8
> +#define LOONGSON2_THSENS_STATUS_REG			0x10
> +#define LOONGSON2_THSENS_OUT_REG			0x14
> +
> +#define LOONGSON2_THSENS_INT_LO				BIT(0)
> +#define LOONGSON2_THSENS_INT_HIGH			BIT(1)
> +#define LOONGSON2_THSENS_OUT_MASK			0xFF
> +
> +struct loongson2_thermal_chip_data {
> +	unsigned int	thermal_sensor_sel;
> +};
> +
> +struct loongson2_thermal_data {
> +	void __iomem	*regs;
> +	const struct loongson2_thermal_chip_data *chip_data;
> +};
> +
> +static int loongson2_thermal_set(struct loongson2_thermal_data *data,
> +					int low, int high, bool enable)
> +{
> +	u64 reg_ctrl = 0;
> +	int reg_off = data->chip_data->thermal_sensor_sel * 2;
> +
> +	low = clamp(-40, low, high);
> +	high = clamp(125, low, high);
> +
> +	low += HECTO;
> +	high += HECTO;
> +
> +	reg_ctrl = low;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_THSENS_CTRL_LOW_REG + reg_off);
> +
> +	reg_ctrl = high;
> +	reg_ctrl |= enable ? 0x100 : 0;
> +	writew(reg_ctrl, data->regs + LOONGSON2_THSENS_CTRL_HI_REG + reg_off);
> +
> +	return 0;
> +}
> +
> +static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
> +{
> +	u32 reg_val;
> +	struct loongson2_thermal_data *data = thermal_zone_device_priv(tz);
> +
> +	reg_val = readl(data->regs + LOONGSON2_THSENS_OUT_REG);
> +	*temp = ((reg_val & LOONGSON2_THSENS_OUT_MASK) - HECTO) * KILO;
> +
> +	return 0;
> +}
> +
> +static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
> +{
> +	struct thermal_zone_device *tzd = dev;
> +	struct loongson2_thermal_data *data = thermal_zone_device_priv(tzd);
> +
> +	writeb(LOONGSON2_THSENS_INT_LO | LOONGSON2_THSENS_INT_HIGH, data->regs +
> +		LOONGSON2_THSENS_STATUS_REG);
> +
> +	thermal_zone_device_update(tzd, THERMAL_EVENT_UNSPECIFIED);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
> +{
> +	struct loongson2_thermal_data *data = thermal_zone_device_priv(tz);
> +
> +	return loongson2_thermal_set(data, low/MILLI, high/MILLI, true);
> +}
> +
> +static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
> +	.get_temp = loongson2_thermal_get_temp,
> +	.set_trips = loongson2_thermal_set_trips,
> +};
> +
> +static int loongson2_thermal_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct loongson2_thermal_data *data;
> +	struct thermal_zone_device *tzd;
> +	int ret, irq, i;
> +
> +	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
> +	if (!data)
> +		return -ENOMEM;
> +
> +	data->chip_data = device_get_match_data(dev);
> +
> +	data->regs = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(data->regs))
> +		return PTR_ERR(data->regs);
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
> +
> +	writeb(LOONGSON2_THSENS_INT_LO | LOONGSON2_THSENS_INT_HIGH, data->regs +
> +		LOONGSON2_THSENS_STATUS_REG);
> +
> +	loongson2_thermal_set(data, 0, 0, false);
> +
> +	for (i = 0; i <= LOONGSON2_MAX_SENSOR_SEL_NUM; i++) {
> +		tzd = devm_thermal_of_zone_register(dev, i, data,
> +			&loongson2_of_thermal_ops);
> +
> +		if (!IS_ERR(tzd))
> +			break;
> +
> +		if (PTR_ERR(tzd) != ENODEV)
> +			continue;
> +
> +		return dev_err_probe(dev, PTR_ERR(tzd), "failed to register");
> +	}
> +
> +	ret = devm_request_threaded_irq(dev, irq, NULL, loongson2_thermal_irq_thread,
> +			IRQF_ONESHOT, "loongson2_thermal", tzd);
> +	if (ret < 0)
> +		return dev_err_probe(dev, ret, "failed to request alarm irq\n");
> +
> +	if (devm_thermal_add_hwmon_sysfs(dev, tzd))
> +		dev_warn(dev, "Failed to add hwmon sysfs attributes\n");
> +
> +	return 0;
> +}
> +
> +static const struct loongson2_thermal_chip_data loongson2_thermal_ls2k1000_data = {
> +	.thermal_sensor_sel = 0,
> +};
> +
> +static const struct of_device_id of_loongson2_thermal_match[] = {
> +	{
> +		.compatible = "loongson,ls2k1000-thermal",
> +		.data = &loongson2_thermal_ls2k1000_data,
> +	},
> +	{ /* end */ }
> +};
> +MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
> +
> +static struct platform_driver loongson2_thermal_driver = {
> +	.driver = {
> +		.name		= "loongson2_thermal",
> +		.of_match_table = of_loongson2_thermal_match,
> +	},
> +	.probe	= loongson2_thermal_probe,
> +};
> +module_platform_driver(loongson2_thermal_driver);
> +
> +MODULE_DESCRIPTION("Loongson2 thermal driver");
> +MODULE_LICENSE("GPL");
> 

Powered by blists - more mailing lists