Message-ID: <a561fd54-4527-e21c-d5f8-f3777d69c255@ti.com>
Date:   Wed, 27 Sep 2023 11:49:45 +0530
From:   MD Danish Anwar <danishanwar@...com>
To:     Vinicius Costa Gomes <vinicius.gomes@...el.com>,
        Andrew Lunn <andrew@...n.ch>,
        Roger Quadros <rogerq@...nel.org>,
        Vignesh Raghavendra <vigneshr@...com>,
        Richard Cochran <richardcochran@...il.com>,
        Paolo Abeni <pabeni@...hat.com>,
        Jakub Kicinski <kuba@...nel.org>,
        Eric Dumazet <edumazet@...gle.com>,
        "David S. Miller" <davem@...emloft.net>, <vladimir.oltean@....com>,
        Simon Horman <horms@...nel.org>
CC:     <netdev@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <srk@...com>, <r-gunasekaran@...com>, Roger Quadros <rogerq@...com>
Subject: Re: [PATCH net-next v2] net: ti: icssg_prueth: add TAPRIO offload
 support

Hi Vinicius,

On 22/09/23 01:44, Vinicius Costa Gomes wrote:
> MD Danish Anwar <danishanwar@...com> writes:
> 
>> ICSSG dual-emac f/w supports Enhanced Scheduled Traffic (EST – defined
>> in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
>> configuration. EST allows express queue traffic to be scheduled
>> (placed) on the wire at specific repeatable time intervals. In
>> Linux kernel, EST configuration is done through tc command and
>> the taprio scheduler in the net core implements a software only
>> scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
>> user indicate "flag 2" in the command which is then parsed by
>> taprio scheduler in net core and indicate that the command is to
>> be offloaded to h/w. taprio then offloads the command to the
>> driver by calling ndo_setup_tc() ndo ops. This patch implements
>> ndo_setup_tc() to offload EST configuration to ICSSG.
>>
>> Signed-off-by: Roger Quadros <rogerq@...com>
>> Signed-off-by: Vignesh Raghavendra <vigneshr@...com>
>> Signed-off-by: MD Danish Anwar <danishanwar@...com>
>> ---
>> Cc: Roger Quadros <rogerq@...com>
>> Cc: Andrew Lunn <andrew@...n.ch>
>>
>> Changes from v1 to v2:
>> *) Rebased on the latest next-20230821 linux-next.
>> *) Dropped the RFC tag as merge window is open now.
>> *) Splitted this patch from the switch mode series [v1].
>> *) Removed TODO comment as asked by Andrew and Roger.
>> *) Changed Copyright to 2023 as asked by Roger.
>>
>> v1: https://lore.kernel.org/all/20230830110847.1219515-1-danishanwar@ti.com/
>>
>>  drivers/net/ethernet/ti/Makefile             |   3 +-
>>  drivers/net/ethernet/ti/icssg/icssg_prueth.c |   5 +-
>>  drivers/net/ethernet/ti/icssg/icssg_prueth.h |   7 +
>>  drivers/net/ethernet/ti/icssg/icssg_qos.c    | 286 +++++++++++++++++++
>>  drivers/net/ethernet/ti/icssg/icssg_qos.h    | 119 ++++++++
>>  5 files changed, 418 insertions(+), 2 deletions(-)
>>  create mode 100644 drivers/net/ethernet/ti/icssg/icssg_qos.c
>>  create mode 100644 drivers/net/ethernet/ti/icssg/icssg_qos.h
>>
>> diff --git a/drivers/net/ethernet/ti/Makefile b/drivers/net/ethernet/ti/Makefile
>> index 34fd7a716ba6..0df60ded1b2d 100644
>> --- a/drivers/net/ethernet/ti/Makefile
>> +++ b/drivers/net/ethernet/ti/Makefile
>> @@ -37,5 +37,6 @@ icssg-prueth-y := k3-cppi-desc-pool.o \
>>  		  icssg/icssg_config.o \
>>  		  icssg/icssg_mii_cfg.o \
>>  		  icssg/icssg_stats.o \
>> -		  icssg/icssg_ethtool.o
>> +		  icssg/icssg_ethtool.o \
>> +		  icssg/icssg_qos.o
>>  obj-$(CONFIG_TI_ICSS_IEP) += icssg/icss_iep.o
>> diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
>> index 6635b28bc672..89c301716926 100644
>> --- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
>> +++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
>> @@ -1166,7 +1166,7 @@ static int emac_phy_connect(struct prueth_emac *emac)
>>  	return 0;
>>  }
>>  
>> -static u64 prueth_iep_gettime(void *clockops_data, struct ptp_system_timestamp *sts)
>> +u64 prueth_iep_gettime(void *clockops_data, struct ptp_system_timestamp *sts)
>>  {
>>  	u32 hi_rollover_count, hi_rollover_count_r;
>>  	struct prueth_emac *emac = clockops_data;
>> @@ -1403,6 +1403,8 @@ static int emac_ndo_open(struct net_device *ndev)
>>  		napi_enable(&emac->tx_chns[i].napi_tx);
>>  	napi_enable(&emac->napi_rx);
>>  
>> +	icssg_qos_tas_init(ndev);
>> +
>>  	/* start PHY */
>>  	phy_start(ndev->phydev);
>>  
>> @@ -1669,6 +1671,7 @@ static const struct net_device_ops emac_netdev_ops = {
>>  	.ndo_set_rx_mode = emac_ndo_set_rx_mode,
>>  	.ndo_eth_ioctl = emac_ndo_ioctl,
>>  	.ndo_get_stats64 = emac_ndo_get_stats64,
>> +	.ndo_setup_tc = icssg_qos_ndo_setup_tc,
>>  };
>>  
>>  /* get emac_port corresponding to eth_node name */
>> diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.h b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
>> index 8b6d6b497010..5712a65bced4 100644
>> --- a/drivers/net/ethernet/ti/icssg/icssg_prueth.h
>> +++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.h
>> @@ -37,6 +37,7 @@
>>  #include "icssg_config.h"
>>  #include "icss_iep.h"
>>  #include "icssg_switch_map.h"
>> +#include "icssg_qos.h"
>>  
>>  #define PRUETH_MAX_MTU          (2000 - ETH_HLEN - ETH_FCS_LEN)
>>  #define PRUETH_MIN_PKT_SIZE     (VLAN_ETH_ZLEN)
>> @@ -174,6 +175,9 @@ struct prueth_emac {
>>  
>>  	struct pruss_mem_region dram;
>>  
>> +	struct prueth_qos qos;
>> +	struct work_struct ts_work;
> 
> This doesn't seem to be used anywhere. Am I missing something?
> 

I cross checked. This is actually not used anywhere. I will drop it.

>> +
>>  	struct delayed_work stats_work;
>>  	u64 stats[ICSSG_NUM_STATS];
>>  };
>> @@ -285,4 +289,7 @@ u32 icssg_queue_level(struct prueth *prueth, int queue);
>>  void emac_stats_work_handler(struct work_struct *work);
>>  void emac_update_hardware_stats(struct prueth_emac *emac);
>>  int emac_get_stat_by_name(struct prueth_emac *emac, char *stat_name);
>> +
>> +u64 prueth_iep_gettime(void *clockops_data, struct ptp_system_timestamp *sts);
>> +
>>  #endif /* __NET_TI_ICSSG_PRUETH_H */
>> diff --git a/drivers/net/ethernet/ti/icssg/icssg_qos.c b/drivers/net/ethernet/ti/icssg/icssg_qos.c
>> new file mode 100644
>> index 000000000000..63a19142ee69
>> --- /dev/null
>> +++ b/drivers/net/ethernet/ti/icssg/icssg_qos.c
>> @@ -0,0 +1,286 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/* Texas Instruments ICSSG PRUETH QoS submodule
>> + * Copyright (C) 2023 Texas Instruments Incorporated - http://www.ti.com/
>> + */
>> +
>> +#include <linux/printk.h>
>> +#include "icssg_prueth.h"
>> +#include "icssg_switch_map.h"
>> +
>> +static void tas_update_fw_list_pointers(struct prueth_emac *emac)
>> +{
>> +	struct tas_config *tas = &emac->qos.tas.config;
>> +
>> +	if ((readb(tas->active_list)) == TAS_LIST0) {
>> +		tas->fw_active_list = emac->dram.va + TAS_GATE_MASK_LIST0;
>> +		tas->fw_shadow_list = emac->dram.va + TAS_GATE_MASK_LIST1;
>> +	} else {
>> +		tas->fw_active_list = emac->dram.va + TAS_GATE_MASK_LIST1;
>> +		tas->fw_shadow_list = emac->dram.va + TAS_GATE_MASK_LIST0;
>> +	}
>> +}
>> +
>> +static void tas_update_maxsdu_table(struct prueth_emac *emac)
>> +{
>> +	struct tas_config *tas = &emac->qos.tas.config;
>> +	u16 __iomem *max_sdu_tbl_ptr;
>> +	u8 gate_idx;
>> +
>> +	/* update the maxsdu table */
>> +	max_sdu_tbl_ptr = emac->dram.va + TAS_QUEUE_MAX_SDU_LIST;
>> +
>> +	for (gate_idx = 0; gate_idx < TAS_MAX_NUM_QUEUES; gate_idx++)
>> +		writew(tas->max_sdu_table.max_sdu[gate_idx], &max_sdu_tbl_ptr[gate_idx]);
>> +}
>> +
>> +static void tas_reset(struct prueth_emac *emac)
>> +{
>> +	struct tas_config *tas = &emac->qos.tas.config;
>> +	int i;
>> +
>> +	for (i = 0; i < TAS_MAX_NUM_QUEUES; i++)
>> +		tas->max_sdu_table.max_sdu[i] = 2048;
>> +
>> +	tas_update_maxsdu_table(emac);
>> +
>> +	writeb(TAS_LIST0, tas->active_list);
>> +
>> +	memset_io(tas->fw_active_list, 0, sizeof(*tas->fw_active_list));
>> +	memset_io(tas->fw_shadow_list, 0, sizeof(*tas->fw_shadow_list));
>> +}
>> +
>> +static int tas_set_state(struct prueth_emac *emac, enum tas_state state)
>> +{
>> +	struct tas_config *tas = &emac->qos.tas.config;
>> +	int ret;
>> +
>> +	if (tas->state == state)
>> +		return 0;
>> +
>> +	switch (state) {
>> +	case TAS_STATE_RESET:
>> +		tas_reset(emac);
>> +		ret = emac_set_port_state(emac, ICSSG_EMAC_PORT_TAS_RESET);
>> +		tas->state = TAS_STATE_RESET;
>> +		break;
>> +	case TAS_STATE_ENABLE:
>> +		ret = emac_set_port_state(emac, ICSSG_EMAC_PORT_TAS_ENABLE);
>> +		tas->state = TAS_STATE_ENABLE;
>> +		break;
>> +	case TAS_STATE_DISABLE:
>> +		ret = emac_set_port_state(emac, ICSSG_EMAC_PORT_TAS_DISABLE);
>> +		tas->state = TAS_STATE_DISABLE;
>> +		break;
>> +	default:
>> +		netdev_err(emac->ndev, "%s: unsupported state\n", __func__);
>> +		ret = -EINVAL;
>> +		break;
>> +	}
>> +
>> +	if (ret)
>> +		netdev_err(emac->ndev, "TAS set state failed %d\n", ret);
>> +	return ret;
>> +}
>> +
>> +static int tas_set_trigger_list_change(struct prueth_emac *emac)
>> +{
>> +	struct tc_taprio_qopt_offload *admin_list = emac->qos.tas.taprio_admin;
>> +	struct tas_config *tas = &emac->qos.tas.config;
>> +	struct ptp_system_timestamp sts;
>> +	u32 change_cycle_count;
>> +	u32 cycle_time;
>> +	u64 base_time;
>> +	u64 cur_time;
>> +
>> +	cycle_time = admin_list->cycle_time - 4; /* -4ns to compensate for IEP wraparound time */
> 
> What's going to happen when the user specifies a schedule with very
> small intervals, like 1ns and 2ns. Would this break anything?
> 

Actually there is a minimum cycle time TAS_MIN_CYCLE_TIME. There should
be a check here

if (admin_list->cycle_time < TAS_MIN_CYCLE_TIME)
	return -EINVAL;

> Ah, just saw that there's a TAS_MIN_WINDOW_DURATION, but I didn't see it
> used anywhere.
> 
>> +	base_time = admin_list->base_time;
>> +	cur_time = prueth_iep_gettime(emac, &sts);
>> +
>> +	if (base_time > cur_time)
>> +		change_cycle_count = DIV_ROUND_UP_ULL(base_time - cur_time, cycle_time);
>> +	else
>> +		change_cycle_count = 1;
>> +
>> +	writel(cycle_time, emac->dram.va + TAS_ADMIN_CYCLE_TIME);
>> +	writel(change_cycle_count, emac->dram.va + TAS_CONFIG_CHANGE_CYCLE_COUNT);
>> +	writeb(admin_list->num_entries, emac->dram.va + TAS_ADMIN_LIST_LENGTH);
>> +
>> +	/* config_change cleared by f/w to ack reception of new shadow list */
>> +	writeb(1, &tas->config_list->config_change);
>> +	/* config_pending cleared by f/w when new shadow list is copied to active list */
>> +	writeb(1, &tas->config_list->config_pending);
>> +
>> +	return emac_set_port_state(emac, ICSSG_EMAC_PORT_TAS_TRIGGER);
>> +}
>> +
>> +static int tas_update_oper_list(struct prueth_emac *emac)
>> +{
>> +	struct tc_taprio_qopt_offload *admin_list = emac->qos.tas.taprio_admin;
>> +	struct tas_config *tas = &emac->qos.tas.config;
>> +	u32 tas_acc_gate_close_time = 0;
>> +	u8 idx, gate_idx, val;
>> +	int ret;
>> +
>> +	tas_update_fw_list_pointers(emac);
>> +
>> +	for (idx = 0; idx < admin_list->num_entries; idx++) {
>> +		writeb(admin_list->entries[idx].gate_mask,
>> +		       &tas->fw_shadow_list->gate_mask_list[idx]);
>> +		tas_acc_gate_close_time += admin_list->entries[idx].interval;
>> +
>> +		/* extend last entry till end of cycle time */
>> +		if (idx == admin_list->num_entries - 1)
>> +			writel(admin_list->cycle_time,
>> +			       &tas->fw_shadow_list->win_end_time_list[idx]);
>> +		else
>> +			writel(tas_acc_gate_close_time,
>> +			       &tas->fw_shadow_list->win_end_time_list[idx]);
> 
> Does this mean that the HW "only" supports that the total duration of
> the schedule to be 4s? If yes, you should detect this and reject those
> huge schedules. 
> 

Yes, the HW only supports shedules with total duration < 4s. I will add
check to reject schedules of more than 4s duration.

>> +	}
>> +
>> +	/* clear remaining entries */
>> +	for (idx = admin_list->num_entries; idx < TAS_MAX_CMD_LISTS; idx++) {
>> +		writeb(0, &tas->fw_shadow_list->gate_mask_list[idx]);
>> +		writel(0, &tas->fw_shadow_list->win_end_time_list[idx]);
>> +	}
>> +
>> +	/* update the Array of gate close time for each queue in each window */
>> +	for (idx = 0 ; idx < admin_list->num_entries; idx++) {
>> +		/* On Linux, only PRUETH_MAX_TX_QUEUES are supported per port */
>> +		for (gate_idx = 0; gate_idx < PRUETH_MAX_TX_QUEUES; gate_idx++) {
>> +			u8 gate_mask_list_idx = readb(&tas->fw_shadow_list->gate_mask_list[idx]);
>> +			u32 gate_close_time = 0;
>> +
>> +			if (gate_mask_list_idx & BIT(gate_idx))
>> +				gate_close_time = readl(&tas->fw_shadow_list->win_end_time_list[idx]);
>> +
>> +			writel(gate_close_time,
>> +			       &tas->fw_shadow_list->gate_close_time_list[idx][gate_idx]);
>> +		}
>> +	}
>> +
>> +	/* tell f/w to swap active & shadow list */
>> +	ret = tas_set_trigger_list_change(emac);
>> +	if (ret) {
>> +		netdev_err(emac->ndev, "failed to swap f/w config list: %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	/* Wait for completion */
>> +	ret = readb_poll_timeout(&tas->config_list->config_change, val, !val,
>> +				 USEC_PER_MSEC, 10 * USEC_PER_MSEC);
>> +	if (ret) {
>> +		netdev_err(emac->ndev, "TAS list change completion time out\n");
>> +		return ret;
>> +	}
>> +
>> +	tas_update_fw_list_pointers(emac);
>> +
>> +	return 0;
>> +}
>> +
>> +static int emac_set_taprio(struct prueth_emac *emac)
>> +{
>> +	struct tc_taprio_qopt_offload *taprio = emac->qos.tas.taprio_admin;
>> +	int ret;
>> +
>> +	if (taprio->cmd == TAPRIO_CMD_DESTROY)
>> +		return tas_set_state(emac, TAS_STATE_DISABLE);
>> +
>> +	if (taprio->cmd != TAPRIO_CMD_REPLACE)
>> +		return -EOPNOTSUPP;
>> +
>> +	ret = tas_update_oper_list(emac);
>> +	if (ret)
>> +		return ret;
>> +
>> +	return tas_set_state(emac, TAS_STATE_ENABLE);
>> +}
>> +
>> +static void emac_cp_taprio(struct tc_taprio_qopt_offload *from,
>> +			   struct tc_taprio_qopt_offload *to)
>> +{
>> +	int i;
>> +
>> +	*to = *from;
>> +	for (i = 0; i < from->num_entries; i++)
>> +		to->entries[i] = from->entries[i];
>> +}
>> +
>> +static int emac_setup_taprio(struct net_device *ndev, struct tc_taprio_qopt_offload *taprio)
>> +{
>> +	struct prueth_emac *emac = netdev_priv(ndev);
>> +	struct tc_taprio_qopt_offload *est_new;
>> +	int ret, idx;
>> +
>> +	if (!netif_running(ndev)) {
>> +		netdev_err(ndev, "interface is down, link speed unknown\n");
>> +		return -ENETDOWN;
>> +	}
>> +
>> +	if (taprio->cycle_time_extension) {
>> +		netdev_err(ndev, "Failed to set cycle time extension");
>> +		return -EOPNOTSUPP;
>> +	}
>> +
>> +	if (taprio->num_entries == 0 ||
>> +	    taprio->num_entries > TAS_MAX_CMD_LISTS) {
>> +		netdev_err(ndev, "unsupported num_entries %ld in taprio config\n",
>> +			   taprio->num_entries);
>> +		return -EINVAL;
>> +	}
>> +
>> +	/* If any time_interval is 0 in between the list, then exit */
>> +	for (idx = 0; idx < taprio->num_entries; idx++) {
>> +		if (taprio->entries[idx].interval == 0) {
>> +			netdev_err(ndev, "0 interval in taprio config not supported\n");
>> +			return -EINVAL;
>> +		}
>> +	}
>> +
>> +	if (emac->qos.tas.taprio_admin)
>> +		devm_kfree(&ndev->dev, emac->qos.tas.taprio_admin);
>> +
>> +	est_new = devm_kzalloc(&ndev->dev,
>> +			       struct_size(est_new, entries, taprio->num_entries),
>> +			       GFP_KERNEL);
> 
> This allocation can fail.
> 

I will add the below check here.

if (!est_new)
	ret -ENOMEM;

>> +	emac_cp_taprio(taprio, est_new);
>> +	emac->qos.tas.taprio_admin = est_new;
>> +	ret = emac_set_taprio(emac);
>> +	if (ret)
>> +		devm_kfree(&ndev->dev, est_new);
>> +
>> +	return ret;
>> +}
>> +
>> +int icssg_qos_ndo_setup_tc(struct net_device *ndev, enum tc_setup_type type,
>> +			   void *type_data)
>> +{
>> +	switch (type) {
>> +	case TC_SETUP_QDISC_TAPRIO:
>> +		return emac_setup_taprio(ndev, type_data);
>> +	default:
>> +		return -EOPNOTSUPP;
>> +	}
>> +}
>> +
>> +void icssg_qos_tas_init(struct net_device *ndev)
>> +{
>> +	struct prueth_emac *emac = netdev_priv(ndev);
>> +	bool need_setup = false;
>> +	struct tas_config *tas;
>> +
>> +	tas = &emac->qos.tas.config;
>> +
>> +	if (tas->state == TAS_STATE_ENABLE)
>> +		need_setup = true;
>> +
>> +	tas->config_list = emac->dram.va + TAS_CONFIG_CHANGE_TIME;
>> +	tas->active_list = emac->dram.va + TAS_ACTIVE_LIST_INDEX;
>> +
>> +	tas_update_fw_list_pointers(emac);
>> +
>> +	tas_set_state(emac, TAS_STATE_RESET);
>> +
>> +	if (need_setup)
>> +		emac_set_taprio(emac);
>> +}
>> diff --git a/drivers/net/ethernet/ti/icssg/icssg_qos.h b/drivers/net/ethernet/ti/icssg/icssg_qos.h
>> new file mode 100644
>> index 000000000000..4e2ddf81d5ec
>> --- /dev/null
>> +++ b/drivers/net/ethernet/ti/icssg/icssg_qos.h
>> @@ -0,0 +1,119 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/* Copyright (C) 2023 Texas Instruments Incorporated - http://www.ti.com/
>> + */
>> +
>> +#ifndef __NET_TI_ICSSG_QOS_H
>> +#define __NET_TI_ICSSG_QOS_H
>> +
>> +#include <linux/atomic.h>
>> +#include <linux/netdevice.h>
>> +#include <net/pkt_sched.h>
>> +
>> +/**
>> + * Maximum number of gate command entries in each list.
>> + */
>> +#define TAS_MAX_CMD_LISTS   (16)
>> +
>> +/**
>> + * Maximum number of transmit queues supported by implementation
>> + */
>> +#define TAS_MAX_NUM_QUEUES  (8)
>> +
>> +/**
>> + * Minimum cycle time supported by implementation (in ns)
>> + */
>> +#define TAS_MIN_CYCLE_TIME  (1000000)
>> +
>> +/**
>> + * Minimum TAS window duration supported by implementation (in ns)
>> + */
>> +#define TAS_MIN_WINDOW_DURATION  (10000)
>> +
>> +/**
>> + * List number 0 or 1. Also the value at memory location TAS_ACTIVE_LIST_INDEX
>> + */
>> +enum tas_list_num {
>> +	TAS_LIST0 = 0,
>> +	TAS_LIST1 = 1
>> +};
>> +
>> +/**
>> + * state of TAS in f/w
>> + */
>> +enum tas_state {
>> +	/* PRU's are idle */
>> +	TAS_STATE_DISABLE = 0,
>> +	/* Enable TAS */
>> +	TAS_STATE_ENABLE = 1,
>> +	/* Firmware will reset the state machine */
>> +	TAS_STATE_RESET = 2,
>> +};
>> +
>> +/**
>> + * Config state machine variables. See IEEE Std 802.1Q-2018 8.6.8.4
>> + */
>> +struct tas_config_list {
>> +	/* New list is copied at this time */
>> +	u64 config_change_time;
>> +	/* config change error counter, incremented if
>> +	 * admin->BaseTime < current time and TAS_enabled is true
>> +	 */
>> +	u32 config_change_error_counter;
>> +	/* True if list update is pending */
>> +	u8 config_pending;
>> +	/* Set to true when application trigger updating of admin list
>> +	 * to active list, cleared when configChangeTime is updated
>> +	 */
>> +	u8 config_change;
>> +};
>> +
>> +/**
>> + * Max SDU table. See IEEE Std 802.1Q-2018 12.29.1.1
>> + */
>> +struct tas_max_sdu_table {
>> +	u16 max_sdu[TAS_MAX_NUM_QUEUES];
>> +};
>> +
>> +/**
>> + * TAS List Structure based on firmware memory map
>> + */
>> +struct tas_firmware_list {
>> +	/* window gate mask list */
>> +	u8 gate_mask_list[TAS_MAX_CMD_LISTS];
>> +	/* window end time list */
>> +	u32 win_end_time_list[TAS_MAX_CMD_LISTS];
>> +	/* Array of gate close time for each queue in each window */
>> +	u32 gate_close_time_list[TAS_MAX_CMD_LISTS][TAS_MAX_NUM_QUEUES];
>> +};
>> +
>> +/**
>> + * Main Time Aware Shaper Handle
>> + */
>> +struct tas_config {
>> +	enum tas_state state;
>> +	struct tas_max_sdu_table max_sdu_table;
>> +	/* Config change variables */
>> +	struct tas_config_list __iomem *config_list;
>> +	/* Whether list 1 or list 2 is the operating list */
>> +	u8 __iomem *active_list;
>> +	/* active List pointer, used by firmware */
>> +	struct tas_firmware_list __iomem *fw_active_list;
>> +	/* shadow List pointer, used by driver */
>> +	struct tas_firmware_list __iomem *fw_shadow_list;
>> +};
>> +
>> +struct prueth_qos_tas {
>> +	struct tc_taprio_qopt_offload *taprio_admin;
>> +	struct tc_taprio_qopt_offload *taprio_oper;
>> +	struct tas_config config;
>> +};
>> +
>> +struct prueth_qos {
>> +	/* IET data structure goes here */
>> +	struct prueth_qos_tas tas;
>> +};
>> +
>> +void icssg_qos_tas_init(struct net_device *ndev);
>> +int icssg_qos_ndo_setup_tc(struct net_device *ndev, enum tc_setup_type type,
>> +			   void *type_data);
>> +#endif /* __NET_TI_ICSSG_QOS_H */
>>
>> base-commit: 940fcc189c51032dd0282cbee4497542c982ac59	
>> -- 
>> 2.34.1
>>
>>
> 

-- 
Thanks and Regards,
Danish

Powered by blists - more mailing lists