[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <43cb48da-6ce5-4501-a3c8-071595810bb3@ti.com>
Date: Thu, 30 Nov 2023 16:19:43 -0600
From: Judith Mendez <jm@...com>
To: Nitin Yadav <n-yadav@...com>, <nm@...com>
CC: <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<vigneshr@...com>, <robh+dt@...nel.org>, <kristo@...nel.org>,
<conor+dt@...nel.org>, <krzysztof.kozlowski+dt@...aro.org>
Subject: Re: [PATCH 1/2] arm64: dts: ti: k3-am62a: Enable UHS mode support for
SD cards
On 10/26/23 2:01 AM, Nitin Yadav wrote:
> Hook up required IO voltage regulators to support UHS modes on
> SD cards.
>
> Signed-off-by: Nitin Yadav <n-yadav@...com>
> ---
> arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> index 9f3dfbfbf369..3ae1ea1997a4 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -102,6 +102,19 @@ vdd_mmc1: regulator-3 {
> gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
> };
>
> + vddshv_sdio: regulator-4 {
> + compatible = "regulator-gpio";
> + regulator-name = "vddshv_sdio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&vddshv_sdio_default_pins>;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
> + states = <1800000 0x0>,
> + <3300000 0x1>;
> + };
> +
> leds {
> compatible = "gpio-leds";
> pinctrl-names = "default";
> @@ -189,6 +202,12 @@ AM62AX_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */
> >;
> };
>
> + vddshv_sdio_default_pins: vddshv-sdio-default-pins {
> + pinctrl-single,pins = <
> + AM62AX_IOPAD(0x07c, PIN_OUTPUT, 7) /* (M19) GPMC0_CLK.GPIO0_31 */
Isn't this ball name N22? I might be wrong, but I did check using
SYSCONFIG tool and datasheet.
> + >;
> + };
> +
> main_mmc1_pins_default: main-mmc1-default-pins {
> pinctrl-single,pins = <
> AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
> @@ -294,6 +313,7 @@ &sdhci1 {
> /* SD/MMC */
> status = "okay";
> vmmc-supply = <&vdd_mmc1>;
> + vqmmc-supply = <&vddshv_sdio>;
> pinctrl-names = "default";
> pinctrl-0 = <&main_mmc1_pins_default>;
> ti,driver-strength-ohm = <50>;
Powered by blists - more mailing lists