linux-kernel - [PATCH 02/14] arm64: zynqmp: Add output-enable pins to SOMs

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <9270938b48c8939ac5dca4ac2c59f1c4a8c564d8.1704728353.git.michal.simek@amd.com>
Date: Mon, 8 Jan 2024 16:39:13 +0100
From: Michal Simek <michal.simek@....com>
To: <linux-kernel@...r.kernel.org>, <monstr@...str.eu>,
	<michal.simek@...inx.com>, <git@...inx.com>
CC: Neal Frager <neal.frager@....com>, Conor Dooley <conor+dt@...nel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, Rob Herring
	<robh+dt@...nel.org>, "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE
 BINDINGS" <devicetree@...r.kernel.org>, "moderated list:ARM/ZYNQ
 ARCHITECTURE" <linux-arm-kernel@...ts.infradead.org>
Subject: [PATCH 02/14] arm64: zynqmp: Add output-enable pins to SOMs

From: Neal Frager <neal.frager@....com>

Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.

Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.

In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@...a000038 && \
  gpio toggle gpio@...a000038

Signed-off-by: Neal Frager <neal.frager@....com>
Signed-off-by: Michal Simek <michal.simek@....com>
---

 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso | 5 +++++
 arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso | 5 +++++
 2 files changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
index 92f4190d564d..e7940067ff3c 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
@@ -185,6 +185,7 @@ conf-rx {
 		conf-tx {
 			pins = "MIO36";
 			bias-disable;
+			output-enable;
 		};
 
 		mux {
@@ -236,6 +237,7 @@ conf-rx {
 		conf-bootstrap {
 			pins = "MIO71", "MIO73", "MIO75";
 			bias-disable;
+			output-enable;
 			low-power-disable;
 		};
 
@@ -243,6 +245,7 @@ conf-tx {
 			pins = "MIO64", "MIO65", "MIO66",
 				"MIO67", "MIO68", "MIO69";
 			bias-disable;
+			output-enable;
 			low-power-enable;
 		};
 
@@ -251,6 +254,7 @@ conf-mdio {
 			slew-rate = <SLEW_RATE_SLOW>;
 			power-source = <IO_STANDARD_LVCMOS18>;
 			bias-disable;
+			output-enable;
 		};
 
 		mux-mdio {
@@ -281,6 +285,7 @@ conf-tx {
 			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
 			"MIO60", "MIO61", "MIO62", "MIO63";
 			bias-disable;
+			output-enable;
 			drive-strength = <4>;
 			slew-rate = <SLEW_RATE_SLOW>;
 		};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
index f88b71f5b07a..f72312926299 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
@@ -168,6 +168,7 @@ conf-rx {
 		conf-tx {
 			pins = "MIO36";
 			bias-disable;
+			output-enable;
 		};
 
 		mux {
@@ -219,6 +220,7 @@ conf-rx {
 		conf-bootstrap {
 			pins = "MIO71", "MIO73", "MIO75";
 			bias-disable;
+			output-enable;
 			low-power-disable;
 		};
 
@@ -226,6 +228,7 @@ conf-tx {
 			pins = "MIO64", "MIO65", "MIO66",
 				"MIO67", "MIO68", "MIO69";
 			bias-disable;
+			output-enable;
 			low-power-enable;
 		};
 
@@ -234,6 +237,7 @@ conf-mdio {
 			slew-rate = <SLEW_RATE_SLOW>;
 			power-source = <IO_STANDARD_LVCMOS18>;
 			bias-disable;
+			output-enable;
 		};
 
 		mux-mdio {
@@ -264,6 +268,7 @@ conf-tx {
 			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
 			"MIO60", "MIO61", "MIO62", "MIO63";
 			bias-disable;
+			output-enable;
 			drive-strength = <4>;
 			slew-rate = <SLEW_RATE_SLOW>;
 		};
-- 
2.36.1