| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <0348afb6-24df-4088-a3f5-6b5df8081c04@phytec.de>
Date: Mon, 22 Jan 2024 03:42:18 +0100
From: Wadim Egorov <w.egorov@...tec.de>
To: Mathieu Othacehe <othacehe@....org>, Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>, Conor Dooley
<conor+dt@...nel.org>, Shawn Guo <shawnguo@...nel.org>, Sascha Hauer
<s.hauer@...gutronix.de>, Pengutronix Kernel Team <kernel@...gutronix.de>,
Fabio Estevam <festevam@...il.com>, NXP Linux Team <linux-imx@....com>, Li
Yang <leoyang.li@....com>, Primoz Fiser <primoz.fiser@...ik.com>, Stefan
Wahren <wahrenst@....net>, Christoph Stoidner <c.stoidner@...tec.de>
CC: <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>, <upstream@...t.phytec.de>
Subject: Re: [PATCH v3 2/2] arm64: dts: imx93: Add phyBOARD-Segin-i.MX93
support
Hi,
Am 19.01.24 um 10:28 schrieb Mathieu Othacehe:
> Add basic support for phyBOARD-Segin-i.MX93.
> Main features are:
> * SD-Card
> * UART
> * I2C
It seems you did not configured any I2C bus/device. So maybe drop it
from the currently supported feature list?
> * eMMC
>
> Signed-off-by: Mathieu Othacehe <othacehe@....org>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx93-phyboard-segin.dts | 119 ++++++++++++++++++
> .../boot/dts/freescale/imx93-phycore-som.dtsi | 56 +++++++++
> 3 files changed, 176 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 2e027675d7bb..65db918c821c 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -201,6 +201,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-iris-v2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-segin.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxca.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx93-tqma9352-mba93xxla.dtb
>
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
> new file mode 100644
> index 000000000000..b256c5e42550
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-phyboard-segin.dts
> @@ -0,0 +1,119 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2023 PHYTEC Messtechnik GmbH
> + * Christoph Stoidner <c.stoidner@...tec.de>
you dropped me from the Authors list :(
> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@...il.com>
> + *
It would be nice if you could link the product page,
https://www.phytec.de/produkte/system-on-modules/phycore-imx-91-93/
> + */
> +/dts-v1/;
> +
> +#include "imx93-phycore-som.dtsi"
> +
> +/{
> + model = "PHYTEC phyBOARD-Segin-i.MX93";
> + compatible = "phytec,imx93-phyboard-segin", "phytec,imx93-phycore-som",
> + "fsl,imx93";
> +
> + chosen {
> + stdout-path = &lpuart1;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "VSD_3V3";
Regulator name is VCC_SD
> + };
> +};
> +
> +/* Console */
> +&lpuart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc1 {
> + no-1-8-v;
> +};
> +
> +/* SD-Card */
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2_default>, <&pinctrl_usdhc2_cd>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
> + bus-width = <4>;
> + cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
> + no-mmc;
> + no-sdio;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + status = "okay";
> +};
> +
> +/* Watchdog */
> +&wdog3 {
> + status = "okay";
> +};
Move the watchdog part to the SoM device tree as it not related to the
carrier board design.
> +
> +&iomuxc {
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX93_PAD_UART1_RXD__LPUART1_RX 0x31e
> + MX93_PAD_UART1_TXD__LPUART1_TX 0x30e
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
> + fsl,pins = <
> + MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e
> + >;
> + };
> +
> + pinctrl_usdhc2_cd: usdhc2cdgrp {
> + fsl,pins = <
> + MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e
> + >;
> + };
> +
> + pinctrl_usdhc2_default: usdhc2grp {
> + fsl,pins = <
> + MX93_PAD_SD2_CLK__USDHC2_CLK 0x179e
> + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e
> + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x138e
> + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x138e
> + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x138e
> + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e
> + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp {
> + fsl,pins = <
> + MX93_PAD_SD2_CLK__USDHC2_CLK 0x179e
> + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e
> + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x138e
> + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x138e
> + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x139e
> + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e
> + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp {
> + fsl,pins = <
> + MX93_PAD_SD2_CLK__USDHC2_CLK 0x178e
> + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e
> + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x139e
> + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x139e
> + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x139e
> + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e
> + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> new file mode 100644
> index 000000000000..0cc156b3c24e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-phycore-som.dtsi
> @@ -0,0 +1,56 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2023 PHYTEC Messtechnik GmbH
> + * Christoph Stoidner <c.stoidner@...tec.de>
Same here, you dropped me from the Authors list :(
> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@...il.com>
> + *
> + */
> +/dts-v1/;
I don't think you need the dts-v1 here as this file gets included by
carrier boards that already defining it.
Regards,
Wadim
> +
> +#include "imx93.dtsi"
> +
> +/{
> + model = "PHYTEC phyCORE-i.MX93";
> + compatible = "phytec,imx93-phycore-som", "fsl,imx93";
> +
> + reserved-memory {
> + ranges;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + alloc-ranges = <0 0x80000000 0 0x40000000>;
> + size = <0 0x10000000>;
> + linux,cma-default;
> + };
> + };
> +};
> +
> +/* eMMC */
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX93_PAD_SD1_CLK__USDHC1_CLK 0x179e
> + MX93_PAD_SD1_CMD__USDHC1_CMD 0x1386
> + MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x138e
> + MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x1386
> + MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x138e
> + MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x1386
> + MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x1386
> + MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x1386
> + MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x1386
> + MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x1386
> + MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x179e
> + >;
> + };
> +};
Powered by blists - more mailing lists