[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <henuash23dwkj5fcmub6sabygwo4kam7fgots2pp2j3eu4asuk@cn3o7a62lo74>
Date: Thu, 20 Jun 2024 11:03:55 -0500
From: Andrew Halaney <ahalaney@...hat.com>
To: Bartosz Golaszewski <brgl@...ev.pl>
Cc: Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>, Conor Dooley <conor+dt@...nel.org>,
linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
Subject: Re: [PATCH 2/2] arm64: dts: qcom: sa8775p-ride-r3: add new board file
On Wed, Jun 19, 2024 at 08:32:54PM GMT, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
>
> Revision 3 of the sa8775p-ride board uses a different PHY for the two
> ethernet ports and supports 2.5G speed. Create a new file for the board
> reflecting the changes.
>
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts | 42 ++++++++++++++++++++
> 2 files changed, 43 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 0c1cebd16649..916fbdbf5631 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -112,6 +112,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8540p-ride.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sa8775p-ride.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sa8775p-ride-r3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-acer-aspire1.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
> new file mode 100644
> index 000000000000..d7f0a25c1fc4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride-r3.dts
> @@ -0,0 +1,42 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2023, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include "sa8775p-ride.dtsi"
> +
> +ðernet0 {
> + phy-mode = "ocsgmii";
> +};
> +
> +ðernet1 {
> + phy-mode = "ocsgmii";
> +};
> +
> +&mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + sgmii_phy0: phy@8 {
> + compatible = "ethernet-phy-id31c3.1c33";
> + reg = <0x8>;
> + device_type = "ethernet-phy";
> + interrupts-extended = <&tlmm 7 IRQ_TYPE_EDGE_FALLING>;
> + reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <11000>;
> + reset-deassert-us = <70000>;
I need to read your other series still wrt "ocsgmii", but any chance you
have access to docs indicating the reset timing? I've never had docs for
the specific Marvell phy on the prior board or the Aquantia one on the
new board...
Boot time is something automotive is always concerned over, so I just
want to make sure that this timing isn't any longer than it needs to be.
Right now it looks the same as the Marvell phy's in the "v2" boards etc
and that made me raise my eyebrows.
Thanks,
Andrew
Powered by blists - more mailing lists