[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240628142742.GH783093@kernel.org>
Date: Fri, 28 Jun 2024 15:27:42 +0100
From: Simon Horman <horms@...nel.org>
To: Marek Vasut <marex@...x.de>
Cc: netdev@...r.kernel.org, Alexandre Torgue <alexandre.torgue@...s.st.com>,
Andrew Lunn <andrew@...n.ch>,
Christophe Roullier <christophe.roullier@...s.st.com>,
"David S . Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Heiner Kallweit <hkallweit1@...il.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
Russell King <linux@...linux.org.uk>, kernel@...electronics.com,
linux-kernel@...r.kernel.org
Subject: Re: [net-next,PATCH v2] net: phy: realtek: Add support for PHY LEDs
on RTL8211F
On Tue, Jun 25, 2024 at 10:42:17PM +0200, Marek Vasut wrote:
> Realtek RTL8211F Ethernet PHY supports 3 LED pins which are used to
> indicate link status and activity. Add minimal LED controller driver
> supporting the most common uses with the 'netdev' trigger.
>
> Signed-off-by: Marek Vasut <marex@...x.de>
> ---
> Cc: Alexandre Torgue <alexandre.torgue@...s.st.com>
> Cc: Andrew Lunn <andrew@...n.ch>
> Cc: Christophe Roullier <christophe.roullier@...s.st.com>
> Cc: David S. Miller <davem@...emloft.net>
> Cc: Eric Dumazet <edumazet@...gle.com>
> Cc: Heiner Kallweit <hkallweit1@...il.com>
> Cc: Jakub Kicinski <kuba@...nel.org>
> Cc: Paolo Abeni <pabeni@...hat.com>
> Cc: Russell King <linux@...linux.org.uk>
> Cc: kernel@...electronics.com
> Cc: linux-kernel@...r.kernel.org
> Cc: netdev@...r.kernel.org
> ---
> V2: - RX and TX are not differentiated, either both are set or not set,
> filter this in rtl8211f_led_hw_is_supported()
> ---
> drivers/net/phy/realtek.c | 106 ++++++++++++++++++++++++++++++++++++++
> 1 file changed, 106 insertions(+)
>
> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
> index 2174893c974f3..bed839237fb55 100644
> --- a/drivers/net/phy/realtek.c
> +++ b/drivers/net/phy/realtek.c
> @@ -32,6 +32,15 @@
> #define RTL8211F_PHYCR2 0x19
> #define RTL8211F_INSR 0x1d
>
> +#define RTL8211F_LEDCR 0x10
> +#define RTL8211F_LEDCR_MODE BIT(15)
> +#define RTL8211F_LEDCR_ACT_TXRX BIT(4)
> +#define RTL8211F_LEDCR_LINK_1000 BIT(3)
> +#define RTL8211F_LEDCR_LINK_100 BIT(1)
> +#define RTL8211F_LEDCR_LINK_10 BIT(0)
> +#define RTL8211F_LEDCR_MASK GENMASK(4, 0)
> +#define RTL8211F_LEDCR_SHIFT 5
> +
Hi Marek,
FWIIW, I think that if you use FIELD_PREP and FIELD_GET then
RTL8211F_LEDCR_SHIFT can be removed.
...
Powered by blists - more mailing lists