| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <e68d659f918ca64e1d377e421cbebf37@manjaro.org>
Date: Wed, 03 Jul 2024 23:16:34 +0200
From: Dragan Simic <dsimic@...jaro.org>
To: Heiko Stuebner <heiko@...ech.de>
Cc: robh@...nel.org, krzk+dt@...nel.org, conor+dt@...nel.org,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
linux-rockchip@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 2/2] arm64: dts: rockchip: add rock5 itx board
Hello Heiko,
Please see a few comments below.
On 2024-07-03 23:05, Heiko Stuebner wrote:
> The Rock 5 ITX as the name suggests is made in the ITX form factor and
s/Rock/ROCK/
> actually build in a form to be used in a regular case even providing
s/build/built/
> connectors for regular front-panel io.
>
> It can be powered either bei 12V, ATX power-supply or PoE.
s/bei/by/
> Notable peripherals are the 4 SATA ports, M.2 M-Key slot, M.2 E-key
> slot,
> 2*2.5Gb pcie-connected ethernet nics.
s/pcie/PCIe/
s/ethernet/Ethernet/
s/nics/NICs/
> As of yet unsupported display options consist of 2*hdmi, DP via type-c,
> eDP + 2*DSI via pcb connectors.
s/hdmi/HDMI/
s/type-c/USB-C/
s/pcb/PCB/
> USB ports are 4*USB3 + 2*USB2 on the back panel and 2-port front-panel
> connector.
>
> Signed-off-by: Heiko Stuebner <heiko@...ech.de>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3588-rock-5itx.dts | 1188 +++++++++++++++++
The new dts file should be named rk3588-rock-5-itx.dts instead, because
the board name deviates from the standard Radxa naming scheme.
> 2 files changed, 1189 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-rock-5itx.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
> b/arch/arm64/boot/dts/rockchip/Makefile
> index e8eba631da23e..0380768586436 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -132,6 +132,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) +=
> rk3588-quartzpro64.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b-pcie-ep.dtbo
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b-pcie-srns.dtbo
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5itx.dtb
The same comment about the file name as above applies here as well.
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-tiger-haikou.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-toybrick-x0.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-turing-rk1.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5itx.dts
> b/arch/arm64/boot/dts/rockchip/rk3588-rock-5itx.dts
> new file mode 100644
> index 0000000000000..41d92ceeeb09c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5itx.dts
> @@ -0,0 +1,1188 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2022 Rockchip Electronics Co., Ltd.
> + * Copyright (c) 2022 Radxa Limited
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include "dt-bindings/usb/pd.h"
> +#include "rk3588.dtsi"
> +
> +/ {
> + model = "Radxa ROCK 5 ITX";
> + compatible = "radxa,rock-5itx", "rockchip,rk3588";
s/5itx/5-itx/
> +
> + aliases {
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc;
> + mmc2 = &sdio;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + adc_keys: adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> + poll-interval = <100>;
> + status = "okay";
> +
> + button-maskrom {
> + label = "Mask Rom";
> + linux,code = <KEY_SETUP>;
> + press-threshold-microvolt = <1750>;
> + };
> + };
> +
> + analog-sound {
> + compatible = "audio-graph-card";
> + label = "rk3588-es8316";
> +
> + widgets = "Microphone", "Mic Jack",
> + "Headphone", "Headphones";
> +
> + routing = "MIC2", "Mic Jack",
> + "Headphones", "HPOL",
> + "Headphones", "HPOR";
> +
> + dais = <&i2s0_8ch_p0>;
> + hp-det-gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_detect>;
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_pins>;
> +
> + power-led1 {
> + gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> +
> + hdd-led2 {
> + gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "disk-activity";
> + };
> + };
> +
> + fan0: pwm-fan {
> + compatible = "pwm-fan";
> + #cooling-cells = <2>;
> + cooling-levels = <0 64 128 192 255>;
> + fan-supply = <&vcc12v_dcin>;
> + pwms = <&pwm14 0 10000 0>;
> + };
> +
> + /* M.2 E-KEY */
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&hym8563>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_h>;
> + reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
> + };
> +
> + typec_vin: regulator-typec-vin {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vbus5v0_typec_en>;
> + regulator-name = "typec_vin";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc12v_dcin: regulator-vcc12v-dcin {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc12v_dcin";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <12000000>;
> + regulator-max-microvolt = <12000000>;
> + };
> +
> + vcc33_io64: regulator-vcc33-io64 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc33_io64";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
> +
> + vcc3v3_ekey: regulator-vcc3v3-ekey {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ekey_en>;
> + regulator-name = "vcc3v3_ekey";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <50000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc3v3_lan: vcc3v3_lan_phy2: regulator-vcc3v3-lan {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_lan";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc_3v3_s3>;
> + };
> +
> + vcc3v3_mkey: regulator-vcc3v3-mkey {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x4_pwren_h>;
> + regulator-name = "vcc3v3_mkey";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <5000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc3v3_sys: regulator-vcc3v3-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
> +
> + vcc5v0_sys: regulator-vcc5v0-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc12v_dcin>;
> + };
> +
> + vcc5v0_usb20: vcc5v0_usb12: vcc5v0_usb34: regulator-vcc5v0-usb {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_host_pwren_h>;
> + regulator-name = "vcc5v0_usb";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_1v1_nldo_s3";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +};
> +
> +&combphy0_ps {
> + status = "okay";
> +};
> +
> +&combphy1_ps {
> + status = "okay";
> +};
> +
> +&combphy2_psu {
> + status = "okay";
> +};
> +
> +&cpu_b0 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> +};
> +
> +&cpu_b1 {
> + cpu-supply = <&vdd_cpu_big0_s0>;
> +};
> +
> +&cpu_b2 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> +};
> +
> +&cpu_b3 {
> + cpu-supply = <&vdd_cpu_big1_s0>;
> +};
> +
> +&cpu_l0 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l1 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l2 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&cpu_l3 {
> + cpu-supply = <&vdd_cpu_lit_s0>;
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu_s0>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0m2_xfer>;
> + status = "okay";
> +
> + vdd_cpu_big0_s0: regulator@42 {
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu_big0_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_big1_s0: regulator@43 {
> + compatible = "rockchip,rk8603", "rockchip,rk8602";
> + reg = <0x43>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu_big1_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1m2_xfer>;
> + status = "okay";
> +
> + vdd_npu_s0: regulator@42 {
> + compatible = "rockchip,rk8602";
> + reg = <0x42>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_npu_s0";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +};
> +
> +/* CAM0 connector */
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3m0_xfer>;
> +};
> +
> +/* M.2 E-key */
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4m1_xfer>;
> +};
> +
> +/* RTC and LCD0 connector */
> +&i2c6 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c6m0_xfer>;
> + status = "okay";
> +
> + hym8563: rtc@51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-output-names = "wifi_32kout";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rtc_int>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +/* Audio codec and CAM1 connector */
> +&i2c7 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c7m0_xfer>;
> + status = "okay";
> +
> + es8316: audio-codec@11 {
> + compatible = "everest,es8316";
> + reg = <0x11>;
> + clocks = <&cru I2S0_8CH_MCLKOUT>;
> + clock-names = "mclk";
> + assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
> + assigned-clock-rates = <12288000>;
> + #sound-dai-cells = <0>;
> +
> + port {
> + es8316_p0_0: endpoint {
> + remote-endpoint = <&i2s0_8ch_p0_0>;
> + };
> + };
> + };
> +};
> +
> +/* FUSB302 and LCD1 connector */
> +&i2c8 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c8m4_xfer>;
> + status = "okay";
> +
> + usbc0: usb-typec@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usbc0_int>;
> + vbus-supply = <&typec_vin>;
> +
> + usb_con: connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + data-role = "dual";
> + power-role = "dual";
> + try-power-role = "sink";
> + op-sink-microwatt = <1000000>;
> + sink-pdos =
> + <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
> + source-pdos =
> + <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + usbc0_orien_sw: endpoint {
> + remote-endpoint = <&usbdp_phy0_orientation_switch>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + usbc0_role_sw: endpoint {
> + remote-endpoint = <&dwc3_0_role_switch>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> + dp_altmode_mux: endpoint {
> + remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c8m4_xfer {
> + rockchip,pins =
> + /* i2c8_scl_m4 */
> + <3 RK_PC2 9 &pcfg_pull_up_drv_level_6>,
> + /* i2c8_sda_m4 */
> + <3 RK_PC3 9 &pcfg_pull_up_drv_level_6>;
> +};
> +
> +&i2s0_8ch {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s0_lrck
> + &i2s0_mclk
> + &i2s0_sclk
> + &i2s0_sdi0
> + &i2s0_sdo0>;
> + status = "okay";
> +
> + i2s0_8ch_p0: port {
> + i2s0_8ch_p0_0: endpoint {
> + dai-format = "i2s";
> + mclk-fs = <256>;
> + remote-endpoint = <&es8316_p0_0>;
> + };
> + };
> +};
> +
> +&package_thermal {
> + polling-delay = <1000>;
> +
> + trips {
> + package_fan0: package-fan0 {
> + hysteresis = <2000>;
> + temperature = <50000>;
> + type = "active";
> + };
> +
> + package_fan1: package-fan1 {
> + hysteresis = <2000>;
> + temperature = <65000>;
> + type = "active";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + cooling-device = <&fan0 THERMAL_NO_LIMIT 1>;
> + trip = <&package_fan0>;
> + };
> + map1 {
> + cooling-device = <&fan0 2 THERMAL_NO_LIMIT>;
> + trip = <&package_fan1>;
> + };
> + };
> +};
> +
> +/* M.2 E-key */
> +&pcie2x1l0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x1_0_perstn_m1_l>;
> + reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_ekey>;
> + status = "okay";
> +};
> +
> +/* RTL8125B_1 */
> +&pcie2x1l1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x1_1_perstn>;
> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_lan>;
> + status = "okay";
> +};
> +
> +/* RTL8125B_2 */
> +&pcie2x1l2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie20x1_2_perstn>;
> + reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_lan_phy2>;
> + status = "okay";
> +};
> +
> +&pcie30phy {
> + data-lanes = <1 1 2 2>;
> + /* separate clock lines from the clock generator to phy and devices
> */
> + rockchip,rx-common-refclk-mode = <0 0 0 0>;
> + status = "okay";
> +};
> +
> +/* ASMedia ASM1164 Sata controller */
> +&pcie3x2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x2_perstn_m1_l>;
> + reset-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc33_io64>;
> + status = "okay";
> +};
> +
> +/* M.2 M.key */
> +&pcie3x4 {
> + num-lanes = <2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x4_perstn_m1_l>;
> + reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_mkey>;
> + status = "okay";
> +};
> +
> +&pwm14 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm14m1_pins>;
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&avcc_1v8_s0>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + no-sdio;
> + no-sd;
> + non-removable;
> + max-frequency = <200000000>;
> + mmc-hs400-1_8v;
> + mmc-hs400-enhanced-strobe;
> + mmc-hs200-1_8v;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + max-frequency = <200000000>;
> + no-sdio;
> + no-mmc;
> + bus-width = <4>;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + disable-wp;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_3v3_s3>;
> + vqmmc-supply = <&vccio_sd_s0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det>;
> + status = "okay";
> +};
> +
> +/* M.2 E-KEY */
> +&sdio {
> + broken-cd;
> + bus-width = <4>;
> + cap-sdio-irq;
> + disable-wp;
> + keep-power-in-suspend;
> + max-frequency = <150000000>;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + no-sd;
> + no-mmc;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdiom0_pins>;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc3v3_ekey>;
> + status = "okay";
> +};
> +
> +&sfc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&fspim2_pins>;
> + status = "okay";
> +
> + spi_flash: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-max-frequency = <50000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <1>;
> + };
> +};
> +
> +&spi2 {
> + status = "okay";
> + assigned-clocks = <&cru CLK_SPI2>;
> + assigned-clock-rates = <200000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
> + num-cs = <1>;
> +
> + pmic@0 {
> + compatible = "rockchip,rk806";
> + spi-max-frequency = <1000000>;
> + reg = <0x0>;
> +
> + interrupt-parent = <&gpio0>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
> + <&rk806_dvs2_null>, <&rk806_dvs3_null>;
> +
> + system-power-controller;
> +
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc5-supply = <&vcc5v0_sys>;
> + vcc6-supply = <&vcc5v0_sys>;
> + vcc7-supply = <&vcc5v0_sys>;
> + vcc8-supply = <&vcc5v0_sys>;
> + vcc9-supply = <&vcc5v0_sys>;
> + vcc10-supply = <&vcc5v0_sys>;
> + vcc11-supply = <&vcc_2v0_pldo_s3>;
> + vcc12-supply = <&vcc5v0_sys>;
> + vcc13-supply = <&vcc_1v1_nldo_s3>;
> + vcc14-supply = <&vcc_1v1_nldo_s3>;
> + vcca-supply = <&vcc5v0_sys>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + rk806_dvs1_null: dvs1-null-pins {
> + pins = "gpio_pwrctrl1";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs2_null: dvs2-null-pins {
> + pins = "gpio_pwrctrl2";
> + function = "pin_fun0";
> + };
> +
> + rk806_dvs3_null: dvs3-null-pins {
> + pins = "gpio_pwrctrl3";
> + function = "pin_fun0";
> + };
> +
> + regulators {
> + vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_gpu_s0";
> + regulator-enable-ramp-delay = <400>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_cpu_lit_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_log_s0: dcdc-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <750000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_log_s0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_vdenc_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_ddr_s0: dcdc-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <900000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_ddr_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <850000>;
> + };
> + };
> +
> + vdd2_ddr_s3: dcdc-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd2_ddr_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_2v0_pldo_s3: dcdc-reg7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_2v0_pldo_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <2000000>;
> + };
> + };
> +
> + vcc_3v3_s3: dcdc-reg8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc_3v3_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vddq_ddr_s0: dcdc-reg9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vddq_ddr_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v8_s3: dcdc-reg10 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + avcc_1v8_s0: pldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "avcc_1v8_s0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_1v8_s0: pldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1v8_s0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + avdd_1v2_s0: pldo-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "avdd_1v2_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v3_s0: pldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_3v3_s0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vccio_sd_s0: pldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vccio_sd_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + pldo6_s3: pldo-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "pldo6_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_0v75_s3: nldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "vdd_0v75_s3";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_ddr_pll_s0: nldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-name = "vdd_ddr_pll_s0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <850000>;
> + };
> + };
> +
> + avdd_0v75_s0: nldo-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "avdd_0v75_s0";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_0v85_s0: nldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-name = "vdd_0v85_s0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <837500>;
> + };
> + };
> +
> + vdd_0v75_s0: nldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "vdd_0v75_s0";
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> + };
> + };
> +};
> +
> +&tsadc {
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-0 = <&uart2m0_xfer>;
> + status = "okay";
> +};
> +
> +/* Connected to M.2 E-key */
> +&uart6 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart6m1_xfer &uart6m1_ctsn &uart6m1_rtsn>;
> + status = "okay";
> +};
> +
> +&u2phy0 {
> + status = "okay";
> +};
> +
> +&u2phy0_otg {
> + status = "okay";
> +};
> +
> +&u2phy1 {
> + status = "okay";
> +};
> +
> +&u2phy1_otg {
> + /* connected to USB3 hub, which is powered by vcc5v0_usb12 */
> + phy-supply = <&vcc5v0_usb12>;
> + status = "okay";
> +};
> +
> +&u2phy2 {
> + status = "okay";
> +};
> +
> +&u2phy2_host {
> + /* connected to USB2 hub, which is powered by vcc5v0_usb20 */
> + phy-supply = <&vcc5v0_usb20>;
> + status = "okay";
> +};
> +
> +&u2phy3 {
> + status = "okay";
> +};
> +
> +&u2phy3_host {
> + phy-supply = <&vcc5v0_usb20>;
> + status = "okay";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&usb_host1_ehci {
> + status = "okay";
> +};
> +
> +&usb_host1_ohci {
> + status = "okay";
> +};
> +
> +&usb_host0_xhci {
> + usb-role-switch;
> + status = "okay";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + dwc3_0_role_switch: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&usbc0_role_sw>;
> + };
> + };
> +};
> +
> +&usb_host1_xhci {
> + dr_mode = "host";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + /* 2.0 hub on port 1 */
> + hub_2_0: hub@1 {
> + compatible = "usb5e3,610";
> + reg = <1>;
> + peer-hub = <&hub_3_0>;
> + vdd-supply = <&vcc5v0_usb12>;
> + };
> +
> + /* 3.0 hub on port 4 */
> + hub_3_0: hub@2 {
> + compatible = "usb5e3,620";
> + reg = <2>;
> + peer-hub = <&hub_2_0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gl3523_reset>;
> + reset-gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>;
> + vdd-supply = <&vcc5v0_usb12>;
> + };
> +};
> +
> +&usbdp_phy0 {
> + mode-switch;
> + orientation-switch;
> + sbu1-dc-gpios = <&gpio4 RK_PB7 GPIO_ACTIVE_HIGH>;
> + sbu2-dc-gpios = <&gpio4 RK_PC0 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + usbdp_phy0_orientation_switch: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&usbc0_orien_sw>;
> + };
> +
> + usbdp_phy0_dp_altmode_mux: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&dp_altmode_mux>;
> + };
> + };
> +};
> +
> +&usbdp_phy1 {
> + rockchip,dp-lane-mux = <2 3>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + hym8563 {
> + rtc_int: rtc-int {
> + rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + led_pins: led-pins {
> + rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>,
> + <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pcie {
> + pcie20x1_2_perstn: pcie20x1-2-perstn {
> + rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie30x1_0_perstn_m1_l: pcie30x1-0-perstn-m1-l {
> + rockchip,pins = <4 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie30x1_1_perstn: pcie30x1-1-perstn {
> + rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie30x2_perstn_m1_l: pcie30x2-perstn-m1-l {
> + rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + pcie30x4_perstn_m1_l: pcie30x4-perstn-m1-l {
> + rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + ekey_en: ekey-en {
> + rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> +
> + pcie30x4_pwren_h: pcie30x4-pwren-h {
> + rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + sound {
> + hp_detect: hp-detect {
> + rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + usb {
> + usb_host_pwren_h: usb-host-pwren-h {
> + rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + vcc5v0_otg_en: vcc5v0-otg-en {
> + rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + gl3523_reset: rl3523-reset {
> + rockchip,pins = <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + usb-typec {
> + usbc0_int: usbc0-int {
> + rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + vbus5v0_typec_en: vbus5v0-typec-en {
> + rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + hdmirx {
> + hdmirx_det: hdmirx-det {
> + rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wireless-wlan {
> + wifi_host_wake_irq: wifi-host-wake-irq {
> + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + bt {
> + bt_enable_h: bt-enable-h {
> + rockchip,pins = <2 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + bt_host_wake_l: bt-host-wake-l {
> + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + bt_wake_l: bt-wake-l {
> + rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + dp {
> + dp1_hpd: dp1-hpd {
> + rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
Powered by blists - more mailing lists