[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <20240818160424.GA156214-robh@kernel.org>
Date: Sun, 18 Aug 2024 10:04:24 -0600
From: Rob Herring <robh@...nel.org>
To: Christian Bruel <christian.bruel@...s.st.com>
Cc: vkoul@...nel.org, kishon@...nel.org, krzk+dt@...nel.org,
conor+dt@...nel.org, mcoquelin.stm32@...il.com,
alexandre.torgue@...s.st.com, p.zabel@...gutronix.de,
linux-phy@...ts.infradead.org, devicetree@...r.kernel.org,
linux-stm32@...md-mailman.stormreply.com,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
fabrice.gasnier@...s.st.com
Subject: Re: [PATCH v2 2/5] dt-bindings: phy: Add STM32MP25 COMBOPHY bindings
On Fri, Aug 16, 2024 at 03:20:54PM +0200, Christian Bruel wrote:
> Document the bindings for STM32 COMBOPHY interface, used to support
> the PCIe and USB3 stm32mp25 drivers.
> Following entries can be used to tune caracterisation parameters
> - st,output-micro-ohms and st,output-vswing-microvolt bindings entries
> to tune the impedance and voltage swing using discrete simulation results
> - st,rx-equalizer register to set the internal rx equalizer filter value.
>
> Signed-off-by: Christian Bruel <christian.bruel@...s.st.com>
> ---
> .../bindings/phy/st,stm32-combophy.yaml | 144 ++++++++++++++++++
> 1 file changed, 144 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml
>
> diff --git a/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml
> new file mode 100644
> index 000000000000..c33a843b83a3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/st,stm32-combophy.yaml
> @@ -0,0 +1,144 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/st,stm32-combophy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectronics STM32MP25 USB3/PCIe COMBOPHY
> +
> +maintainers:
> + - Christian Bruel <christian.bruel@...s.st.com>
> +
> +description:
> + Single lane PHY shared (exclusive) between the USB3 and PCIe controllers.
> + Supports 5Gbit/s for USB3 and PCIe gen2 or 2.5Gbit/s for PCIe gen1.
> +
> +properties:
> + compatible:
> + const: st,stm32mp25-combophy
> +
> + reg:
> + maxItems: 1
> +
> + "#phy-cells":
> + const: 1
> + description: |
> + The cells contain the following arguments.
> +
> + - description: The PHY type
> + enum:
> + - PHY_TYPE_USB3
> + - PHY_TYPE_PCIE
> +
> + clocks:
> + minItems: 2
> + items:
> + - description: apb Bus clock mandatory to access registers.
> + - description: ker Internal RCC reference clock for USB3 or PCIe
> + - description: pad Optional on board clock input for PCIe only. Typically an
> + external 100Mhz oscillator wired on dedicated CLKIN pad. Used as reference
> + clock input instead of the ker
> +
> + clock-names:
> + minItems: 2
> + items:
> + - const: apb
> + - const: ker
> + - const: pad
> +
> + resets:
> + maxItems: 1
> +
> + reset-names:
> + const: phy
> +
> + power-domains:
> + maxItems: 1
> +
> + wakeup-source: true
> +
> + interrupts:
> + maxItems: 1
> + description: interrupt used for wakeup
> +
> + access-controllers:
> + minItems: 1
> + maxItems: 2
> +
> + st,syscfg:
> + $ref: /schemas/types.yaml#/definitions/phandle
> + description: Phandle to the SYSCON entry required for configuring PCIe
> + or USB3.
> +
> + st,ssc-on:
> + type: boolean
> + description:
> + A boolean property whose presence indicates that the SSC for common clock
> + needs to be set.
> +
> + st,rx-equalizer:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0
> + maximum: 7
> + default: 2
> + description:
> + A 3 bit value to tune the RX fixed equalizer setting for optimal eye compliance
> +
> + st,output-micro-ohms:
> + minimum: 3999000
> + maximum: 6090000
> + default: 4968000
> + description:
> + A value property to tune the Single Ended Output Impedance, simulations results
> + at 25C for a VDDP=0.8V. The hardware accepts discrete values in this range.
> +
> + st,output-vswing-microvolt:
> + minimum: 442000
> + maximum: 803000
> + default: 803000
> + description:
> + A value property in microvolt to tune the Single Ended Output Voltage Swing to change the
> + Vlo, Vhi for a VDDP = 0.8V. The hardware accepts discrete values in this range.
> +
> +required:
> + - compatible
> + - reg
> + - st,syscfg
> + - '#phy-cells'
> + - resets
> + - reset-names
> + - clocks
> + - clock-names
> +
> +allOf:
> + - if:
> + required:
> + - wakeup-source
> + then:
> + anyOf:
> + - required: [interrupts]
> + - required: [interrupts-extended]
Drop this if/then. We should have this somewhere common as it applies to
all.
Reviewed-by: Rob Herring (Arm) <robh@...nel.org>
Powered by blists - more mailing lists