[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <ed46220cc4c52d630fc481c8148fc749242c368d.1724244281.git.daniel@makrotopia.org>
Date: Wed, 21 Aug 2024 13:46:50 +0100
From: Daniel Golle <daniel@...rotopia.org>
To: "David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>, Andrew Lunn <andrew@...n.ch>,
Heiner Kallweit <hkallweit1@...il.com>,
Russell King <linux@...linux.org.uk>,
Christian Marangi <ansuelsmth@...il.com>,
Bartosz Golaszewski <bartosz.golaszewski@...aro.org>,
Daniel Golle <daniel@...rotopia.org>,
Robert Marko <robimarko@...il.com>,
Russell King <rmk+kernel@...linux.org.uk>,
Chad Monroe <chad.monroe@...ran.com>,
John Crispin <john@...ozen.org>, netdev@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: [PATCH net-next 2/2] net: phy: aquantia: allow forcing order of MDI
pairs
Normally, the MDI reversal configuration is taken from the MDI_CFG pin.
However, some hardware designs require overriding the value configured
by that bootstrap pin. The PHY allows doing that by setting a bit which
allows ignoring the state of the MDI_CFG pin and configuring whether
the order of MDI pairs should be normal (ABCD) or reverse (DCBA).
Introduce two boolean properties which allow forcing either normal or
reverse order of the MDI pairs from DT.
Signed-off-by: Daniel Golle <daniel@...rotopia.org>
---
drivers/net/phy/aquantia/aquantia_main.c | 35 ++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c
index e982e9ce44a59..33a6eb55d99d4 100644
--- a/drivers/net/phy/aquantia/aquantia_main.c
+++ b/drivers/net/phy/aquantia/aquantia_main.c
@@ -11,6 +11,7 @@
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/bitfield.h>
+#include <linux/of.h>
#include <linux/phy.h>
#include "aquantia.h"
@@ -71,6 +72,11 @@
#define MDIO_AN_TX_VEND_INT_MASK2 0xd401
#define MDIO_AN_TX_VEND_INT_MASK2_LINK BIT(0)
+#define PMAPMD_RSVD_VEND_PROV 0xe400
+#define PMAPMD_RSVD_VEND_PROV_MDI_CONF GENMASK(1, 0)
+#define PMAPMD_RSVD_VEND_PROV_MDI_REVERSE BIT(0)
+#define PMAPMD_RSVD_VEND_PROV_MDI_FORCE BIT(1)
+
#define MDIO_AN_RX_LP_STAT1 0xe820
#define MDIO_AN_RX_LP_STAT1_1000BASET_FULL BIT(15)
#define MDIO_AN_RX_LP_STAT1_1000BASET_HALF BIT(14)
@@ -474,6 +480,31 @@ static void aqr107_chip_info(struct phy_device *phydev)
fw_major, fw_minor, build_id, prov_id);
}
+int aqr107_config_mdi(struct phy_device *phydev)
+{
+ struct device_node *np = phydev->mdio.dev.of_node;
+ bool force_normal, force_reverse;
+
+ force_normal = of_property_read_bool(np, "marvell,force-mdi-order-normal");
+ force_reverse = of_property_read_bool(np, "marvell,force-mdi-order-reverse");
+
+ if (force_normal && force_reverse)
+ return -EINVAL;
+
+ if (force_normal)
+ return phy_modify_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_RSVD_VEND_PROV,
+ PMAPMD_RSVD_VEND_PROV_MDI_CONF,
+ PMAPMD_RSVD_VEND_PROV_MDI_FORCE);
+
+ if (force_reverse)
+ return phy_modify_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_RSVD_VEND_PROV,
+ PMAPMD_RSVD_VEND_PROV_MDI_CONF,
+ PMAPMD_RSVD_VEND_PROV_MDI_REVERSE |
+ PMAPMD_RSVD_VEND_PROV_MDI_FORCE);
+
+ return 0;
+}
+
static int aqr107_config_init(struct phy_device *phydev)
{
struct aqr107_priv *priv = phydev->priv;
@@ -503,6 +534,10 @@ static int aqr107_config_init(struct phy_device *phydev)
if (ret)
return ret;
+ ret = aqr107_config_mdi(phydev);
+ if (ret)
+ return ret;
+
/* Restore LED polarity state after reset */
for_each_set_bit(led_active_low, &priv->leds_active_low, AQR_MAX_LEDS) {
ret = aqr_phy_led_active_low_set(phydev, index, led_active_low);
--
2.46.0
Powered by blists - more mailing lists