[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20240830113347.4048370-3-ciprianmarian.costea@oss.nxp.com>
Date: Fri, 30 Aug 2024 14:33:47 +0300
From: Ciprian Costea <ciprianmarian.costea@....nxp.com>
To: Chester Lin <chester62515@...il.com>,
Matthias Brugger <mbrugger@...e.com>,
Ghennadi Procopciuc <ghennadi.procopciuc@....nxp.com>,
Shawn Guo <shawnguo@...nel.org>,
Sascha Hauer <s.hauer@...gutronix.de>,
Fabio Estevam <festevam@...il.com>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>
Cc: Pengutronix Kernel Team <kernel@...gutronix.de>,
linux-arm-kernel@...ts.infradead.org,
imx@...ts.linux.dev,
devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
NXP S32 Linux Team <s32@....com>,
Ciprian Marian Costea <ciprianmarian.costea@....nxp.com>
Subject: [PATCH v2 2/2] arm64: dts: s32g2: Disable support for SD/eMMC UHS mode
From: Ciprian Marian Costea <ciprianmarian.costea@....nxp.com>
Disable SD/eMMC UHS modes for NXP boards which do not set VCCQ voltage
supply to 1.8V by default, such as S32G274A-EVB and S32G274A-RDB2.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@....nxp.com>
---
arch/arm64/boot/dts/freescale/s32g274a-evb.dts | 1 +
arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts | 9 +++++++++
2 files changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts
index 7ab917f547ef..b9a119eea2b7 100644
--- a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts
+++ b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts
@@ -39,5 +39,6 @@ &usdhc0 {
pinctrl-1 = <&pinctrl_usdhc0_100mhz>;
pinctrl-2 = <&pinctrl_usdhc0_200mhz>;
disable-wp;
+ no-1-8-v;
status = "okay";
};
diff --git a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts
index 8739f63771bc..aaa61a8ad0da 100644
--- a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts
+++ b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts
@@ -45,5 +45,14 @@ &usdhc0 {
pinctrl-1 = <&pinctrl_usdhc0_100mhz>;
pinctrl-2 = <&pinctrl_usdhc0_200mhz>;
disable-wp;
+ /* Remove no-1-8-v to enable higher speed modes for SD card.
+ * However, this is not enough to enable HS400 or HS200 modes for eMMC.
+ * In this case, the position of the resistor R797 must be changed
+ * from A to B before removing the property.
+ * If the property is removed without changing the resistor position,
+ * HS*00 may be enabled, but the interface might be unstable because of
+ * the wrong VCCQ voltage applied to the eMMC.
+ */
+ no-1-8-v;
status = "okay";
};
--
2.45.2
Powered by blists - more mailing lists