[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20240920-pmbus-wp-v1-5-d679ef31c483@baylibre.com>
Date: Fri, 20 Sep 2024 18:47:06 +0200
From: Jerome Brunet <jbrunet@...libre.com>
To: Liam Girdwood <lgirdwood@...il.com>, Mark Brown <broonie@...nel.org>,
Jean Delvare <jdelvare@...e.com>, Guenter Roeck <linux@...ck-us.net>,
Jonathan Corbet <corbet@....net>
Cc: linux-kernel@...r.kernel.org, linux-hwmon@...r.kernel.org,
linux-doc@...r.kernel.org, Jerome Brunet <jbrunet@...libre.com>
Subject: [PATCH 5/5] hwmon: (pmbus/core) add wp module param
Add a module parameter to force the write protection mode of pmbus chips.
2 protections modes are provided to start with:
* 0: Remove the write protection if possible
* 1: Enable full write protection if possible
Of course, if the parameter is not provided, the default write protection
status of the pmbus chips is left untouched.
Suggested-by: Guenter Roeck <linux@...ck-us.net>
Signed-off-by: Jerome Brunet <jbrunet@...libre.com>
---
Documentation/admin-guide/kernel-parameters.txt | 4 ++
drivers/hwmon/pmbus/pmbus_core.c | 74 ++++++++++++++++++-------
2 files changed, 59 insertions(+), 19 deletions(-)
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 09126bb8cc9f..e41d13f46140 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -4672,6 +4672,10 @@
Format: { parport<nr> | timid | 0 }
See also Documentation/admin-guide/parport.rst.
+ pmbus.wp= [HW] PMBus Chips write protection forced mode
+ Format: { 0 | 1 }
+ See drivers/hwmon/pmbus/pmbus_core.c
+
pmtmr= [X86] Manual setup of pmtmr I/O Port.
Override pmtimer IOPort with a hex value.
e.g. pmtmr=0x508
diff --git a/drivers/hwmon/pmbus/pmbus_core.c b/drivers/hwmon/pmbus/pmbus_core.c
index 363def768888..ca5803bfd24a 100644
--- a/drivers/hwmon/pmbus/pmbus_core.c
+++ b/drivers/hwmon/pmbus/pmbus_core.c
@@ -31,6 +31,20 @@
#define PMBUS_ATTR_ALLOC_SIZE 32
#define PMBUS_NAME_SIZE 24
+/*
+ * PMBus write protect forced mode:
+ * PMBus may come up with a variety of write protection configuration.
+ * 'pmbus_wp' may be used if a particular write protection is necessary.
+ * The ability to actually alter the protection may also depend on the chip
+ * so the actual runtime write protection configuration may differ from
+ * the requested one. pmbus_core currently support the following value:
+ * - 0: write protection removed
+ * - 1: write protection fully enabled, including OPERATION and VOUT_COMMAND
+ * registers. Chips essentially become read-only with this.
+ */
+static int wp = -1;
+module_param(wp, int, 0444);
+
struct pmbus_sensor {
struct pmbus_sensor *next;
char name[PMBUS_NAME_SIZE]; /* sysfs sensor name */
@@ -2658,6 +2672,45 @@ static void pmbus_remove_pec(void *dev)
device_remove_file(dev, &dev_attr_pec);
}
+static void pmbus_init_wp(struct i2c_client *client, struct pmbus_data *data)
+{
+ int ret;
+
+ switch (wp) {
+ case 0:
+ _pmbus_write_byte_data(client, 0xff,
+ PMBUS_WRITE_PROTECT, 0);
+ break;
+
+ case 1:
+ _pmbus_write_byte_data(client, 0xff,
+ PMBUS_WRITE_PROTECT, PB_WP_ALL);
+ break;
+
+ default:
+ /* Ignore the other values */
+ break;
+ }
+
+ ret = _pmbus_read_byte_data(client, 0xff, PMBUS_WRITE_PROTECT);
+
+ switch (ret) {
+ case PB_WP_ALL:
+ data->flags |= PMBUS_OP_PROTECTED;
+ fallthrough;
+ case PB_WP_OP:
+ data->flags |= PMBUS_VOUT_PROTECTED;
+ fallthrough;
+ case PB_WP_VOUT:
+ data->flags |= PMBUS_WRITE_PROTECTED | PMBUS_SKIP_STATUS_CHECK;
+ break;
+
+ default:
+ /* Ignore manufacturer specific and invalid as well as errors */
+ break;
+ }
+}
+
static int pmbus_init_common(struct i2c_client *client, struct pmbus_data *data,
struct pmbus_driver_info *info)
{
@@ -2711,25 +2764,8 @@ static int pmbus_init_common(struct i2c_client *client, struct pmbus_data *data,
* faults, and we should not try it. Also, in that case, writes into
* limit registers need to be disabled.
*/
- if (!(data->flags & PMBUS_NO_WRITE_PROTECT)) {
- ret = _pmbus_read_byte_data(client, 0xff, PMBUS_WRITE_PROTECT);
-
- switch (ret) {
- case PB_WP_ALL:
- data->flags |= PMBUS_OP_PROTECTED;
- fallthrough;
- case PB_WP_OP:
- data->flags |= PMBUS_VOUT_PROTECTED;
- fallthrough;
- case PB_WP_VOUT:
- data->flags |= PMBUS_WRITE_PROTECTED | PMBUS_SKIP_STATUS_CHECK;
- break;
-
- default:
- /* Ignore manufacturer specific and invalid as well as errors */
- break;
- }
- }
+ if (!(data->flags & PMBUS_NO_WRITE_PROTECT))
+ pmbus_init_wp(client, data);
if (data->info->pages)
pmbus_clear_faults(client);
--
2.45.2
Powered by blists - more mailing lists