lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <ZxdCcsq0Zjjm4hYT@dragon>
Date: Tue, 22 Oct 2024 14:13:06 +0800
From: Shawn Guo <shawnguo2@...h.net>
To: Lukasz Majewski <lukma@...x.de>
Cc: Rob Herring <robh@...nel.org>, Krzysztof Kozlowski <krzk+dt@...nel.org>,
	Conor Dooley <conor+dt@...nel.org>, Shawn Guo <shawnguo@...nel.org>,
	Sascha Hauer <s.hauer@...gutronix.de>,
	Pengutronix Kernel Team <kernel@...gutronix.de>,
	Fabio Estevam <festevam@...il.com>, devicetree@...r.kernel.org,
	imx@...ts.linux.dev, linux-arm-kernel@...ts.infradead.org,
	linux-kernel@...r.kernel.org, Stefan Wahren <wahrenst@....net>
Subject: Re: [PATCH v9 4/4] ARM: dts: mxs: Add descriptions for imx287 based
 btt3-[012] devices

On Mon, Oct 21, 2024 at 12:02:24PM +0200, Lukasz Majewski wrote:
> The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to
> some extend similar to already upstreamed XEA devices, hence are
> using common imx28-lwe.dtsi file.
> 
> New, imx28-btt3.dtsi has been added to embrace common DTS
> properties for different HW revisions for this device.
> 
> As a result - changes introduced in imx28-btt3-[012].dts are
> minimal.
> 
> Signed-off-by: Lukasz Majewski <lukma@...x.de>
> 
> ---
> Changes for v2:
> - Rename dts file from btt3-[012] to imx28-btt3-[012] to match current
>   linux kernel naming convention
> - Remove 'wlf,wm8974' from compatible for codec@1a
> 
> Changes for v3:
> - Keep alphabethical order for Makefile entries
> 
> Changes for v4:
> - Change compatible for btt3 board (to 'lwn,imx28-btt3')
> 
> Changes for v5:
> - Combine patch, which adds btt3-[012] with one adding board entry to
>   fsl.yaml
> 
> Changes for v6:
> - Make the patch series for adding entry in fsl.yaml and btt3
> 
> Changes for v7:
> - Use "panel" property as suggested by the community
> - Use panel-timing to specify the display parameters
> - Update subject line with correct tags
> 
> Changes for v8:
> - Use GPIO_ACTIVE_HIGH instead of '0'
> - Add the comment regarding mac address specification
> - Remove superfluous comment
> - Change wifi-en-pin node name
> 
> Changes for v9:
> - Remove not used 'pm-ignore-notify'
> - Add display names for 'panel-dpi' compatible to avoid Schema warnings
> ---
>  arch/arm/boot/dts/nxp/mxs/Makefile         |   3 +
>  arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts |  12 +
>  arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts |   8 +
>  arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts |  40 +++
>  arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi  | 312 +++++++++++++++++++++
>  5 files changed, 375 insertions(+)
>  create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
>  create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
>  create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
>  create mode 100644 arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
> 
> diff --git a/arch/arm/boot/dts/nxp/mxs/Makefile b/arch/arm/boot/dts/nxp/mxs/Makefile
> index a430d04f9c69..96dd31ea19ba 100644
> --- a/arch/arm/boot/dts/nxp/mxs/Makefile
> +++ b/arch/arm/boot/dts/nxp/mxs/Makefile
> @@ -8,6 +8,9 @@ dtb-$(CONFIG_ARCH_MXS) += \
>  	imx28-apf28.dtb \
>  	imx28-apf28dev.dtb \
>  	imx28-apx4devkit.dtb \
> +	imx28-btt3-0.dtb \
> +	imx28-btt3-1.dtb \
> +	imx28-btt3-2.dtb \
>  	imx28-cfa10036.dtb \
>  	imx28-cfa10037.dtb \
>  	imx28-cfa10049.dtb \
> diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
> new file mode 100644
> index 000000000000..6ac46e4b21bb
> --- /dev/null
> +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
> @@ -0,0 +1,12 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2024
> + * Lukasz Majewski, DENX Software Engineering, lukma@...x.de
> + */
> +
> +/dts-v1/;
> +#include "imx28-btt3.dtsi"
> +
> +&hog_pins_rev {
> +	fsl,pull-up = <MXS_PULL_ENABLE>;
> +};
> diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
> new file mode 100644
> index 000000000000..213fe931c58b
> --- /dev/null
> +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
> @@ -0,0 +1,8 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2024
> + * Lukasz Majewski, DENX Software Engineering, lukma@...x.de
> + */
> +
> +/dts-v1/;
> +#include "imx28-btt3.dtsi"
> diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
> new file mode 100644
> index 000000000000..314a22cb736f
> --- /dev/null
> +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
> @@ -0,0 +1,40 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2024
> + * Lukasz Majewski, DENX Software Engineering, lukma@...x.de
> + */
> +
> +/dts-v1/;
> +#include "imx28-btt3.dtsi"
> +
> +/ {
> +	panel {
> +		compatible = "powertip,st7272", "panel-dpi";
> +		power-supply = <&reg_3v3>;
> +		width-mm = <70>;
> +		height-mm = <52>;
> +
> +		panel-timing {
> +			clock-frequency = <6500000>;
> +			hactive = <320>;
> +			vactive = <240>;
> +			hfront-porch = <20>;
> +			hback-porch = <68>;
> +			hsync-len = <30>;
> +			vfront-porch = <4>;
> +			vback-porch = <14>;
> +			vsync-len = <4>;
> +

Nit: can we drop this newline?

> +			hsync-active = <0>;
> +			vsync-active = <0>;
> +			de-active = <1>;
> +			pixelclk-active = <1>;
> +		};
> +
> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&display_out>;
> +			};
> +		};
> +	};
> +};
> diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
> new file mode 100644
> index 000000000000..cb999082f0f4
> --- /dev/null
> +++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
> @@ -0,0 +1,312 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2024
> + * Lukasz Majewski, DENX Software Engineering, lukma@...x.de
> + */
> +/dts-v1/;
> +#include "imx28-lwe.dtsi"
> +
> +/ {
> +	model = "BTT3";
> +
> +	compatible = "lwn,imx28-btt3", "fsl,imx28";
> +
> +	chosen {
> +	       bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1 quiet";
> +	};
> +
> +	memory@...00000 {
> +		reg = <0x40000000 0x10000000>;
> +		device_type = "memory";
> +	};
> +
> +	panel {
> +		compatible = "powertip,hx8238a", "panel-dpi";
> +		power-supply = <&reg_3v3>;
> +		width-mm = <70>;
> +		height-mm = <52>;
> +
> +		panel-timing {
> +			clock-frequency = <6500000>;
> +			hactive = <320>;
> +			vactive = <240>;
> +			hfront-porch = <20>;
> +			hback-porch = <38>;
> +			hsync-len = <30>;
> +			vfront-porch = <4>;
> +			vback-porch = <14>;
> +			vsync-len = <4>;
> +

Ditto

> +			hsync-active = <0>;
> +			vsync-active = <0>;
> +			de-active = <0>;
> +			pixelclk-active = <1>;
> +		};
> +
> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&display_out>;
> +			};
> +		};
> +	};
> +
> +	poweroff {
> +		compatible = "gpio-poweroff";
> +		gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	sound {
> +		compatible = "simple-audio-card";
> +		simple-audio-card,name = "BTTC Audio";
> +		simple-audio-card,widgets = "Speaker", "BTTC Speaker";
> +		simple-audio-card,routing = "BTTC Speaker", "SPKOUTN", "BTTC Speaker", "SPKOUTP";

Have a newline between property list and child node.

> +		simple-audio-card,dai-link@0 {
> +			format = "left_j";
> +			bitclock-master = <&dai0_master>;
> +			frame-master = <&dai0_master>;
> +			mclk-fs = <256>;

Ditto

> +			dai0_master: cpu {
> +				sound-dai = <&saif0>;
> +			};

Have a newline between nodes.

> +			codec {
> +				sound-dai = <&wm89xx>;
> +				clocks = <&saif0>;
> +			};
> +		};
> +	};
> +
> +	wifi_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_en_pin_bttc>;
> +		reset-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
> +		/* W1-163 needs 60us for WL_EN to be low and */
> +		/* 150ms after high before downloading FW is possible */
> +		post-power-on-delay-ms = <200>;
> +		power-off-delay-us = <100>;
> +	};
> +};
> +
> +&auart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&auart0_2pins_a>;
> +	status = "okay";
> +};
> +
> +&auart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&auart3_pins_a>;
> +	uart-has-rtscts;
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	wm89xx: codec@1a {

audio-codec for node name.

> +		compatible = "wlf,wm8940";
> +		reg = <0x1a>;
> +		#sound-dai-cells = <0>;
> +	};
> +};
> +
> +&lcdif {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&lcdif_24bit_pins_a>, <&lcdif_sync_pins_bttc>,
> +		    <&lcdif_reset_pins_bttc>;
> +	status = "okay";
> +
> +	port {
> +		display_out: endpoint {
> +			remote-endpoint = <&panel_in>;
> +		};
> +	};
> +};
> +
> +&mac0 {
> +	clocks = <&clks 57>, <&clks 57>, <&clks 64>;
> +	clock-names = "ipg", "ahb", "enet_out";
> +	phy-handle = <&mac0_phy>;
> +	phy-mode = "rmii";
> +	phy-supply = <&reg_3v3>;
> +	/*
> +	 * This MAC address is adjusted during production.
> +	 * Value specified below is used as a fallback during recovery.
> +	 */
> +	local-mac-address = [ 00 11 B8 00 BF 8A ];
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		mac0_phy: ethernet-phy@0 {
> +			/* LAN8720Ai - PHY ID */
> +			compatible = "ethernet-phy-id0007.c0f0","ethernet-phy-ieee802.3-c22";
> +			reg = <0>;
> +			smsc,disable-energy-detect;
> +			max-speed = <100>;
> +

Nit: unneeded newline.

> +			reset-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
> +			reset-assert-us = <1000>;
> +			reset-deassert-us = <1000>;
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&hog_pins_a>, <&hog_pins_rev>;
> +
> +	hog_pins_a: hog@0 {
> +		reg = <0>;
> +		fsl,pinmux-ids = <
> +			MX28_PAD_GPMI_RDY2__GPIO_0_22
> +			MX28_PAD_GPMI_RDY3__GPIO_0_23
> +			MX28_PAD_GPMI_RDN__GPIO_0_24
> +			MX28_PAD_LCD_VSYNC__GPIO_1_28
> +			MX28_PAD_SSP2_SS1__GPIO_2_20
> +			MX28_PAD_SSP2_SS2__GPIO_2_21
> +			MX28_PAD_AUART2_CTS__GPIO_3_10
> +			MX28_PAD_AUART2_RTS__GPIO_3_11
> +			MX28_PAD_GPMI_WRN__GPIO_0_25
> +			MX28_PAD_ENET0_RXD2__GPIO_4_9
> +			MX28_PAD_ENET0_TXD2__GPIO_4_11
> +		>;
> +		fsl,drive-strength = <MXS_DRIVE_4mA>;
> +		fsl,voltage = <MXS_VOLTAGE_HIGH>;
> +		fsl,pull-up = <MXS_PULL_DISABLE>;
> +	};
> +
> +	hog_pins_rev: hog@1 {
> +		reg = <1>;
> +		fsl,pinmux-ids = <
> +			MX28_PAD_ENET0_RXD3__GPIO_4_10
> +			MX28_PAD_ENET0_TX_CLK__GPIO_4_5
> +			MX28_PAD_ENET0_COL__GPIO_4_14
> +			MX28_PAD_ENET0_CRS__GPIO_4_15
> +		>;
> +		fsl,drive-strength = <MXS_DRIVE_4mA>;
> +		fsl,voltage = <MXS_VOLTAGE_HIGH>;
> +		fsl,pull-up = <MXS_PULL_DISABLE>;
> +	};
> +
> +	keypad_pins_bttc: keypad-bttc@0 {
> +		reg = <0>;
> +		fsl,pinmux-ids = <
> +			MX28_PAD_GPMI_D00__GPIO_0_0
> +			MX28_PAD_AUART0_CTS__GPIO_3_2
> +			MX28_PAD_AUART0_RTS__GPIO_3_3
> +			MX28_PAD_GPMI_D03__GPIO_0_3
> +			MX28_PAD_GPMI_D04__GPIO_0_4
> +			MX28_PAD_GPMI_D05__GPIO_0_5
> +			MX28_PAD_GPMI_D06__GPIO_0_6
> +			MX28_PAD_GPMI_D07__GPIO_0_7
> +			MX28_PAD_GPMI_CE1N__GPIO_0_17
> +			MX28_PAD_GPMI_CE2N__GPIO_0_18
> +			MX28_PAD_GPMI_CE3N__GPIO_0_19
> +			MX28_PAD_GPMI_RDY0__GPIO_0_20
> +		>;
> +		fsl,drive-strength = <MXS_DRIVE_4mA>;
> +		fsl,voltage = <MXS_VOLTAGE_HIGH>;
> +		fsl,pull-up = <MXS_PULL_DISABLE>;
> +	};
> +
> +	lcdif_sync_pins_bttc: lcdif-bttc@0 {
> +		reg = <0>;
> +		fsl,pinmux-ids = <
> +			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
> +			MX28_PAD_LCD_ENABLE__LCD_ENABLE
> +			MX28_PAD_LCD_HSYNC__LCD_HSYNC
> +			MX28_PAD_LCD_RD_E__LCD_VSYNC
> +		>;
> +		fsl,drive-strength = <MXS_DRIVE_4mA>;
> +		fsl,voltage = <MXS_VOLTAGE_HIGH>;
> +		fsl,pull-up = <MXS_PULL_DISABLE>;
> +	};
> +
> +	lcdif_reset_pins_bttc: lcdif-bttc@1 {
> +		reg = <1>;
> +		fsl,pinmux-ids = <
> +			MX28_PAD_LCD_RESET__GPIO_3_30
> +		>;
> +		fsl,drive-strength = <MXS_DRIVE_4mA>;
> +		fsl,voltage = <MXS_VOLTAGE_HIGH>;
> +		fsl,pull-up = <MXS_PULL_ENABLE>;
> +	};
> +
> +	ssp1_sdio_pins_a: ssp1-sdio@0 {
> +		reg = <0>;
> +		fsl,pinmux-ids = <
> +			MX28_PAD_SSP1_DATA0__SSP1_D0
> +			MX28_PAD_GPMI_D01__SSP1_D1
> +			MX28_PAD_GPMI_D02__SSP1_D2
> +			MX28_PAD_SSP1_DATA3__SSP1_D3
> +			MX28_PAD_SSP1_CMD__SSP1_CMD
> +			MX28_PAD_SSP1_SCK__SSP1_SCK
> +		>;
> +		fsl,drive-strength = <MXS_DRIVE_8mA>;
> +		fsl,voltage = <MXS_VOLTAGE_HIGH>;
> +		fsl,pull-up = <MXS_PULL_ENABLE>;
> +	};
> +
> +	wifi_en_pin_bttc: wifi-en-pin@0 {
> +		reg = <0>;
> +		fsl,pinmux-ids = <
> +			MX28_PAD_GPMI_CLE__GPIO_0_27
> +		>;
> +		fsl,drive-strength = <MXS_DRIVE_8mA>;
> +		fsl,voltage = <MXS_VOLTAGE_HIGH>;
> +		fsl,pull-up = <MXS_PULL_ENABLE>;
> +	};
> +};
> +
> +&pwm {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pwm3_pins_a>;
> +	status = "okay";
> +};
> +
> +&reg_usb_5v {
> +	gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&saif0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&saif0_pins_a>;
> +	#sound-dai-cells = <0>;
> +	assigned-clocks = <&clks 53>;
> +	assigned-clock-rates = <12000000>;
> +	status = "okay";
> +};
> +
> +&saif1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&saif1_pins_a>;

> +	fsl,saif-master = <&saif0>;
> +	#sound-dai-cells = <0>;

Can we flip these two properties, so that we have vendor specific
property after generic one?

Shawn

> +	status = "okay";
> +};
> +
> +&ssp1 {
> +	compatible = "fsl,imx28-mmc";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ssp1_sdio_pins_a>;
> +	bus-width = <4>;
> +	no-1-8-v;       /* force 3.3V VIO */
> +	non-removable;
> +	vmmc-supply = <&reg_3v3>;
> +	mmc-pwrseq = <&wifi_pwrseq>;
> +	keep-power-in-suspend;
> +	status = "okay";
> +
> +	wlan@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +&ssp2 {
> +	compatible = "fsl,imx28-spi";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi2_pins_a>;
> +	status = "okay";
> +};
> -- 
> 2.39.5
> 


Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ