[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <a4n3w62bg6x2iux4z7enu3po56hr5pcavjfmvtzdcwv2w4ptrr@ssvfdrltfg5y>
Date: Mon, 24 Mar 2025 13:26:36 +0530
From: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
To: george.moussalem@...look.com
Cc: Vinod Koul <vkoul@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>, Conor Dooley <conor+dt@...nel.org>,
Nitheesh Sekar <quic_nsekar@...cinc.com>, Varadarajan Narayanan <quic_varada@...cinc.com>,
Bjorn Helgaas <bhelgaas@...gle.com>, Lorenzo Pieralisi <lpieralisi@...nel.org>,
Krzysztof Wilczyński <kw@...ux.com>, Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>, linux-arm-msm@...r.kernel.org, linux-phy@...ts.infradead.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org, linux-pci@...r.kernel.org,
20250317100029.881286-2-quic_varada@...cinc.com, Sricharan R <quic_srichara@...cinc.com>
Subject: Re: [PATCH v6 5/6] arm64: dts: qcom: ipq5018: Add PCIe related nodes
On Fri, Mar 21, 2025 at 04:14:43PM +0400, George Moussalem via B4 Relay wrote:
> From: Nitheesh Sekar <quic_nsekar@...cinc.com>
>
> Add phy and controller nodes for a 2-lane Gen2 and
Controller is Gen 3 capable but you are limiting it to Gen 2.
> a 1-lane Gen2 PCIe bus. IPQ5018 has 8 MSI SPI interrupts and
> one global interrupt.
>
> Signed-off-by: Nitheesh Sekar <quic_nsekar@...cinc.com>
> Signed-off-by: Sricharan R <quic_srichara@...cinc.com>
> Signed-off-by: George Moussalem <george.moussalem@...look.com>
One comment below. With that addressed,
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
> ---
> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 234 +++++++++++++++++++++++++++++++++-
> 1 file changed, 232 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> index 8914f2ef0bc4..d08034b57e80 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> @@ -147,6 +147,40 @@ usbphy0: phy@...00 {
> status = "disabled";
> };
>
> + pcie1_phy: phy@...00{
> + compatible = "qcom,ipq5018-uniphy-pcie-phy";
> + reg = <0x0007e000 0x800>;
> +
> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> +
> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
> +
> + #clock-cells = <0>;
> + #phy-cells = <0>;
> +
> + num-lanes = <1>;
> +
> + status = "disabled";
> + };
> +
> + pcie0_phy: phy@...00{
> + compatible = "qcom,ipq5018-uniphy-pcie-phy";
> + reg = <0x00086000 0x800>;
> +
> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> +
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> +
> + #clock-cells = <0>;
> + #phy-cells = <0>;
> +
> + num-lanes = <2>;
> +
> + status = "disabled";
> + };
> +
> tlmm: pinctrl@...0000 {
> compatible = "qcom,ipq5018-tlmm";
> reg = <0x01000000 0x300000>;
> @@ -170,8 +204,8 @@ gcc: clock-controller@...0000 {
> reg = <0x01800000 0x80000>;
> clocks = <&xo_board_clk>,
> <&sleep_clk>,
> - <0>,
> - <0>,
> + <&pcie0_phy>,
> + <&pcie1_phy>,
> <0>,
> <0>,
> <0>,
> @@ -387,6 +421,202 @@ frame@...8000 {
> status = "disabled";
> };
> };
> +
> + pcie1: pcie@...00000 {
> + compatible = "qcom,pcie-ipq5018";
> + reg = <0x80000000 0xf1d>,
> + <0x80000f20 0xa8>,
> + <0x80001000 0x1000>,
> + <0x00078000 0x3000>,
> + <0x80100000 0x1000>,
> + <0x0007b000 0x1000>;
> + reg-names = "dbi",
> + "elbi",
> + "atu",
> + "parf",
> + "config",
> + "mhi";
> + device_type = "pci";
> + linux,pci-domain = <0>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> + max-link-speed = <2>;
This still needs some justification. If Qcom folks didn't reply, atleast move
this to board dts with a comment saying that the link is not coming up with
Gen3.
- Mani
--
மணிவண்ணன் சதாசிவம்
Powered by blists - more mailing lists