[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <gyeppjlzfpmazj5seohhab75mbhv5kyzdbxh7iqddd33dnah3n@w2tpd5gme2rq>
Date: Wed, 26 Mar 2025 02:21:48 +0200
From: Dmitry Baryshkov <dmitry.baryshkov@....qualcomm.com>
To: Prashanth K <prashanth.k@....qualcomm.com>
Cc: Konrad Dybcio <konrad.dybcio@....qualcomm.com>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
cros-qcom-dts-watchers@...omium.org, linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v1 0/5] Add snps,dis_u3_susphy_quirk for some QC targets
On Tue, Mar 25, 2025 at 08:31:55PM +0530, Prashanth K wrote:
>
>
> On 25-03-25 08:11 pm, Konrad Dybcio wrote:
> > On 3/25/25 1:30 PM, Prashanth K wrote:
> >> During device mode initialization on certain QC targets, before the
> >> runstop bit is set, sometimes it's observed that the GEVNTADR{LO/HI}
> >> register write fails. As a result, GEVTADDR registers are still 0x0.
> >> Upon setting runstop bit, DWC3 controller attempts to write the new
> >> events to address 0x0, causing an SMMU fault and system crash. More
> >> info about the crash at [1].
> >>
> >> This was initially observed on SM8450 and later reported on few
> >> other targets as well. As suggested by Qualcomm HW team, clearing
> >> the GUSB3PIPECTL.SUSPHY bit resolves the issue by preventing register
> >> write failures. Address this by setting the snps,dis_u3_susphy_quirk
> >> to keep the GUSB3PIPECTL.SUSPHY bit cleared. This change was tested
> >> on multiple targets (SM8350, SM8450 QCS615 etc.) for over an year
> >> and hasn't exhibited any side effects.
> >>
> >> [1]: https://lore.kernel.org/all/fa94cbc9-e637-ba9b-8ec8-67c6955eca98@quicinc.com/
> >>
> >> Prashanth K (3):
> >> arm64: dts: qcom: sm8150: Add snps,dis_u3_susphy_quirk
> >> arm64: dts: qcom: sm8350: Add snps,dis_u3_susphy_quirk
> >> arm64: dts: qcom: sm8450: Add snps,dis_u3_susphy_quirk
It is hard to belive that this quirk is to be set for SM8150, SM8350,
SM8450, but not SM8250.
> >>
> >> Pratham Pratap (2):
> >> arm64: dts: qcom: qcs615: Add snps,dis_u3_susphy_quirk
> >> arm64: dts: qcom: qdu1000: Add snps,dis_u3_susphy_quirk
> >
> > Are there more targets affected, from the list of the ones currently
> > supported upstream?
> >
> > Konrad
>
> My initial plan was to add it for all the QC platforms, but wasn't
> confident enough about it. Because we have seen the issue only on these
> targets and hence tested only on these.
>
> Regards,
> Prashanth K
--
With best wishes
Dmitry
Powered by blists - more mailing lists