lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20250501072923.1262414-4-p-bhagat@ti.com>
Date: Thu, 1 May 2025 12:59:23 +0530
From: Paresh Bhagat <p-bhagat@...com>
To: <nm@...com>, <vigneshr@...com>, <praneeth@...com>
CC: <kristo@...nel.org>, <robh@...nel.org>, <krzk+dt@...nel.org>,
        <conor+dt@...nel.org>, <linux-arm-kernel@...ts.infradead.org>,
        <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <khasim@...com>, <v-singh1@...com>, <afd@...com>
Subject: [PATCH 3/3] arm64: dts: ti: Add support for AM62D2-EVM

AM62D EVM evaluation module (EVM) is a low-cost expandable platform board
designed for TI’s AM62D2 SoC. It supports the following interfaces:

* 4 GB LPDDR4 RAM
* x2 Gigabit Ethernet expansion connectors
* x4 3.5mm TRS Audio Jack Line In
* x4 3.5mm TRS Audio Jack Line Out
* x2 Audio expansion connectors
* x1 Type-A USB 2.0, x1 Type-C dual-role device (DRD) USB 2.0
* x1 UHS-1 capable µSD card slot
* 32 GB eMMC Flash
* 512 Mb OSPI NOR flash
* x4 UARTs via USB 2.0-B
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs

Add basic support for AM62D2-EVM.

Schematics: https://www.ti.com/lit/zip/sprcal5

Signed-off-by: Paresh Bhagat <p-bhagat@...com>
---
 arch/arm64/boot/dts/ti/Makefile          |   3 +
 arch/arm64/boot/dts/ti/k3-am62d2-evm.dts | 449 +++++++++++++++++++++++
 2 files changed, 452 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am62d2-evm.dts

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 03d4cecfc001..80c6636a711d 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk-nand.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am62a7-phyboard-lyra-rdk.dtb
 
+# Boards with AM62Dx SoC
+dtb-$(CONFIG_ARCH_K3) += k3-am62d2-evm.dtb
+
 # Boards with AM62Px SoC
 dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb
 
diff --git a/arch/arm64/boot/dts/ti/k3-am62d2-evm.dts b/arch/arm64/boot/dts/ti/k3-am62d2-evm.dts
new file mode 100644
index 000000000000..7a12ebe72c16
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62d2-evm.dts
@@ -0,0 +1,449 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * AM62D2 EVM: https://www.ti.com/lit/zip/sprcal5
+ *
+ * Copyright (C) 2025 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-am62a7.dtsi"
+
+#include "k3-timesync-router.h"
+
+/ {
+	compatible = "ti,am62d2-evm", "ti,am62d2";
+	model = "Texas Instruments AM62D2 EVM";
+
+	aliases {
+		serial0 = &wkup_uart0;
+		serial1 = &mcu_uart0;
+		serial2 = &main_uart0;
+		mmc1 = &sdhci1;
+		rtc0 = &wkup_rtc0;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@...00000 {
+		device_type = "memory";
+		/* 4G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* global cma region */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x00 0x2000000>;
+			alloc-ranges = <0x00 0xc0000000 0x00 0x2000000>;
+			linux,cma-default;
+		};
+
+		c7x_0_dma_memory_region: c7x-dma-memory@...00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x99800000 0x00 0x100000>;
+			no-map;
+		};
+
+		c7x_0_memory_region: c7x-memory@...00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x99900000 0x00 0xf00000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@...00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b800000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: r5f-dma-memory@...00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b900000 0x00 0xf00000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@...00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c800000 0x00 0x100000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-dma-memory@...00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c900000 0x00 0xf00000>;
+			no-map;
+		};
+
+		secure_tfa_ddr: tfa@...80000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		secure_ddr: optee@...00000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			alignment = <0x1000>;
+			no-map;
+		};
+	};
+
+	opp-table {
+		/* Requires VDD_CORE at 0v85 */
+		opp-1400000000 {
+			opp-hz = /bits/ 64 <1400000000>;
+			opp-supported-hw = <0x01 0x0004>;
+			clock-latency-ns = <6000000>;
+		};
+	};
+
+	vout_pd: regulator-1 {
+		/* TPS65988 PD CONTROLLER OUTPUT */
+		compatible = "regulator-fixed";
+		regulator-name = "vout_pd";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vmain_pd: load-switch {
+		/* Output of TPS22811 */
+		compatible = "regulator-fixed";
+		regulator-name = "vmain_pd";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vout_pd>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_5v0: regulator-2 {
+		/* Output of TPS630702RNMR */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vmain_pd>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: regulator-3 {
+		/* TPS22918DBVR */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	vddshv_sdio: regulator-4 {
+		compatible = "regulator-gpio";
+		regulator-name = "vddshv_sdio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vddshv_sdio_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		gpios = <&main_gpio1 31 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+};
+
+&mcu_pmx0 {
+	wkup_uart0_pins_default: wkup-uart0-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_MCU_IOPAD(0x0024, PIN_INPUT, 0) /* (C9) WKUP_UART0_RXD */
+			AM62DX_MCU_IOPAD(0x0028, PIN_OUTPUT, 0) /* (E9) WKUP_UART0_TXD */
+			AM62DX_MCU_IOPAD(0x002c, PIN_INPUT, 0) /* (C10) WKUP_UART0_CTSn */
+			AM62DX_MCU_IOPAD(0x0030, PIN_OUTPUT, 0) /* (C8) WKUP_UART0_RTSn */
+		>;
+	};
+};
+
+/* WKUP UART0 is used for DM firmware logs */
+&wkup_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_uart0_pins_default>;
+	status = "reserved";
+};
+
+&main_pmx0 {
+	main_uart0_pins_default: main-uart0-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x01c8, PIN_INPUT, 0) /* (E14) UART0_RXD */
+			AM62DX_IOPAD(0x01cc, PIN_OUTPUT, 0) /* (D15) UART0_TXD */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (D17) I2C0_SCL */
+			AM62DX_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (E16) I2C0_SDA */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x01e8, PIN_INPUT_PULLUP, 0) /* (C17) I2C1_SCL */
+			AM62DX_IOPAD(0x01ec, PIN_INPUT_PULLUP, 0) /* (E17) I2C1_SDA */
+		>;
+	};
+
+	main_i2c2_pins_default: main-i2c2-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x00b0, PIN_INPUT_PULLUP, 1) /* (M22) GPMC0_CSn2.I2C2_SCL */
+			AM62DX_IOPAD(0x00b4, PIN_INPUT_PULLUP, 1) /* (M20) GPMC0_CSn3.I2C2_SDA */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x023c, PIN_INPUT, 0) /* (C21) MMC1_CMD */
+			AM62DX_IOPAD(0x0234, PIN_OUTPUT, 0) /* (E22) MMC1_CLK */
+			AM62DX_IOPAD(0x0230, PIN_INPUT, 0) /* (B22) MMC1_DAT0 */
+			AM62DX_IOPAD(0x022c, PIN_INPUT_PULLUP, 0) /* (D21) MMC1_DAT1 */
+			AM62DX_IOPAD(0x0228, PIN_INPUT_PULLUP, 0) /* (C22) MMC1_DAT2 */
+			AM62DX_IOPAD(0x0224, PIN_INPUT_PULLUP, 0) /* (D22) MMC1_DAT3 */
+			AM62DX_IOPAD(0x0240, PIN_INPUT, 0) /* (E18) MMC1_SDCD */
+			AM62DX_IOPAD(0x0244, PIN_INPUT, 0) /* (D18) MMC1_SDWP */
+		>;
+	};
+
+	main_mdio1_pins_default: main-mdio1-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x160, PIN_OUTPUT, 0) /* (V12) MDIO0_MDC */
+			AM62DX_IOPAD(0x15c, PIN_INPUT, 0) /* (V13) MDIO0_MDIO */
+		>;
+	};
+
+	main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x01d4, PIN_INPUT, 7) /* (C15) UART0_RTSn.GPIO1_23 */
+		>;
+	};
+
+	vddshv_sdio_pins_default: vddshv-sdio-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_IOPAD(0x1F4, PIN_OUTPUT, 7) /* (M19) GPMC0_CLK.GPIO1_31 */
+		>;
+	};
+};
+
+&mcu_pmx0 {
+	status = "okay";
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			AM62DX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
+		>;
+	};
+};
+
+&mcu_gpio0 {
+	status = "okay";
+};
+
+&main_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	typec_pd0: usb-power-controller@3f {
+		compatible = "ti,tps6598x";
+		reg = <0x3f>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			self-powered;
+			data-role = "dual";
+			power-role = "sink";
+			port {
+				usb_con_hs: endpoint {
+					remote-endpoint = <&usb0_hs_ep>;
+				};
+			};
+		};
+	};
+
+	exp1: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio1>;
+		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+
+		gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+			"MMC1_SD_EN", "VPP_EN",
+			"GPIO_DIX_RST", "IO_EXP_OPT_EN",
+			"DIX_INT", "GPIO_eMMC_RSTn",
+			"CPLD2_DONE", "CPLD2_INTN",
+			"CPLD1_DONE", "CPLD1_INTN",
+			"USB_TYPEA_OC_INDICATION", "PCM1_INT",
+			"PCM2_INT", "GPIO_PCM1_RST",
+			"TEST_GPIO2", "GPIO_PCM2_RST",
+			"IO_MCAN0_STB", "IO_MCAN1_STB",
+			"PD_I2C_IRQ", "IO_EXP_TEST_LED";
+	};
+
+	exp2: gpio@23 {
+		compatible = "ti,tca6424";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "", "DAC_LAT_CTRL",
+			"CPLD1_JTAGENB", "CPLD1_PROGRAMN",
+			"CPLD2_JTAGENB", "CPLD2_PROGRAMN",
+			"", "",
+			"", "",
+			"", "",
+			"", "",
+			"", "",
+			"", "",
+			"SoC_I2C0_SCL", "SoC_I2C0_SDA";
+	};
+};
+
+&main_i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	clock-frequency = <100000>;
+	bootph-all;
+};
+
+&main_i2c2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c2_pins_default>;
+	clock-frequency = <400000>;
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	status = "okay";
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vddshv_sdio>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	disable-wp;
+};
+
+&main_gpio0 {
+	status = "okay";
+};
+
+&main_gpio1 {
+	status = "okay";
+};
+
+&main_gpio_intr {
+	status = "okay";
+};
+
+&main_uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+	interrupts-extended = <&gic500 GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>,
+			<&main_pmx0 0x1c8>; /* (D14) UART0_RXD PADCONFIG114 */
+	interrupt-names = "irq", "wakeup";
+};
+
+/* main_timer2 is used by C7x DSP */
+&main_timer2 {
+	status = "reserved";
+};
+
+&usb0 {
+	usb-role-switch;
+
+	port {
+		usb0_hs_ep: endpoint {
+			remote-endpoint = <&usb_con_hs>;
+		};
+	};
+};
+
+&mailbox0_cluster0 {
+	mbox_r5_0: mbox-r5-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&mailbox0_cluster1 {
+	mbox_c7x_0: mbox-c7x-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&mailbox0_cluster2 {
+	mbox_mcu_r5_0: mbox-mcu-r5-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&wkup_r5fss0 {
+	status = "okay";
+};
+
+&wkup_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster0 &mbox_r5_0>;
+	memory-region = <&wkup_r5fss0_core0_dma_memory_region &wkup_r5fss0_core0_memory_region>;
+};
+
+&mcu_r5fss0 {
+	status = "okay";
+};
+
+&mcu_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster2 &mbox_mcu_r5_0>;
+	memory-region = <&mcu_r5fss0_core0_dma_memory_region &mcu_r5fss0_core0_memory_region>;
+};
+
+&c7x_0 {
+	mboxes = <&mailbox0_cluster1 &mbox_c7x_0>;
+	memory-region = <&c7x_0_dma_memory_region &c7x_0_memory_region>;
+	status = "okay";
+};
+
+/* main_rti4 is used by C7x DSP */
+&main_rti4 {
+	status = "reserved";
+};
+
+&timesync_router {
+	/* Use Time Sync Router to map GENF1 input to HW3_TS_PUSH output */
+	mux-reg-masks-state = <
+		/* pps [cpsw cpts genf1] in17 -> out12 [cpsw cpts hw3_push] */
+		K3_TS_OFFSET(12, 0x0001ffff, 17)
+		>;
+	status = "okay";
+};
-- 
2.34.1


Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ