[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <19dd4cc6-c110-4c2d-b725-5e7bd1a4226c@ti.com>
Date: Fri, 2 May 2025 16:39:23 +0530
From: "Donadkar, Rishikesh" <r-donadkar@...com>
To: Devarsh Thakkar <devarsht@...com>, <nm@...com>, <vigneshr@...com>
CC: <kristo@...nel.org>, <robh@...nel.org>, <krzk+dt@...nel.org>,
<conor+dt@...nel.org>, <vaishnav.a@...com>, <y-abhilashchandra@...com>,
<s-jain1@...com>, <jai.luthra@...ux.dev>,
<jai.luthra@...asonboard.com>, <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<imx@...ts.linux.dev>
Subject: Re: [PATCH v1 2/4] arm64: dts: ti: k3-am62x: Add required voltage
supplies for IMX219
On 02-05-2025 13:45, Devarsh Thakkar wrote:
> On 29/04/25 21:11, Rishikesh Donadkar wrote:
>> The device tree overlay for the IMX219 sensor requires three voltage
>> supplies to be defined: VANA (analog), VDIG (digital core), and VDDL
>> (digital I/O).
>>
>> Add the corresponding voltage supply definitions to avoid dtbs_check
>> warnings.
>>
> On a side-note device-tree overlay requiring these voltages is an
> implied reason, it's mainly because the schematics mention that and
> bindings want to capture same topography in device-tree too.
>
> So maybe good to mention that and share schematic link too in commit
> message :
>
> https://datasheets.raspberrypi.com/camera/camera-module-2-schematics.pdf
>
> With these changes, feel free to add,
>
> Reviewed-by: Devarsh Thakkar <devarsht@...com>
Hi Devarsh, Thanks for the review. I will do this in the next revision.
>
> Regards
> Devarsh
>
>> Signed-off-by: Rishikesh Donadkar <r-donadkar@...com>
>> ---
>> .../boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso | 31 +++++++++++++++++++
>> 1 file changed, 31 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
>> index dd090813a32d6..149c59c071823 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
>> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-csi2-imx219.dtso
>> @@ -15,6 +15,33 @@ clk_imx219_fixed: imx219-xclk {
>> #clock-cells = <0>;
>> clock-frequency = <24000000>;
>> };
>> +
>> + reg_2p8v: regulator-2p8v {
>> + compatible = "regulator-fixed";
>> + regulator-name = "2P8V";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + vin-supply = <&vcc_3v3_sys>;
>> + regulator-always-on;
>> + };
>> +
>> + reg_1p8v: regulator-1p8v {
>> + compatible = "regulator-fixed";
>> + regulator-name = "1P8V";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + vin-supply = <&vcc_3v3_sys>;
>> + regulator-always-on;
>> + };
>> +
>> + reg_1p2v: regulator-1p2v {
>> + compatible = "regulator-fixed";
>> + regulator-name = "1P2V";
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + vin-supply = <&vcc_3v3_sys>;
>> + regulator-always-on;
>> + };
>> };
>>
>> &main_i2c2 {
>> @@ -40,6 +67,10 @@ ov5640: camera@10 {
>>
>> clocks = <&clk_imx219_fixed>;
>>
>> + VANA-supply = <®_2p8v>;
>> + VDIG-supply = <®_1p8v>;
>> + VDDL-supply = <®_1p2v>;
>> +
>> reset-gpios = <&exp1 13 GPIO_ACTIVE_HIGH>;
>>
>> port {
Powered by blists - more mailing lists