| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20250724094912.253723-5-e@freeshell.de>
Date: Thu, 24 Jul 2025 02:48:47 -0700
From: E Shattow <e@...eshell.de>
To: Emil Renner Berthing <kernel@...il.dk>,
Conor Dooley <conor@...nel.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Paul Walmsley <paul.walmsley@...ive.com>,
Palmer Dabbelt <palmer@...belt.com>,
Albert Ou <aou@...s.berkeley.edu>,
Alexandre Ghiti <alex@...ti.fr>
Cc: devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
E Shattow <e@...eshell.de>,
linux-riscv@...ts.infradead.org
Subject: [PATCH v1 4/4] riscv: dts: starfive: add Milk-V Mars CM Lite system-on-module
Milk-V Mars CM Lite is a System-on-Module based on the Milk-V Mars CM
without the onboard eMMC storage component populated and configured
instead for SD3.0 Card Slot on that interface via 100-pin connector.
Link to Milk-V Mars CM Lite schematics: https://github.com/milkv-mars/mars-files/tree/main/Mars-CM_Hardware_Schematices
Link to StarFive JH7110 Technical Reference Manual: https://doc-en.rvspace.org/JH7110/TRM/index.html
Link to Raspberry Pi CM4IO datasheet: https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Add the devicetree file to make use of StarFive JH7110 common supported
features PMIC, EEPROM, UART, I2C, GPIO, PCIe, QSPI Flash, PWM, and
Ethernet. Also configure the eMMC interface mmc0 for SD Card use and
configure the common SD Card interface mmc1 for onboard SDIO BT+WiFi.
Signed-off-by: E Shattow <e@...eshell.de>
---
arch/riscv/boot/dts/starfive/Makefile | 1 +
.../dts/starfive/jh7110-milkv-marscm-lite.dts | 176 ++++++++++++++++++
2 files changed, 177 insertions(+)
create mode 100644 arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
index 79742617ddab..62b659f89ba7 100644
--- a/arch/riscv/boot/dts/starfive/Makefile
+++ b/arch/riscv/boot/dts/starfive/Makefile
@@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb
dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-deepcomputing-fml13v01.dtb
dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-emmc.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-lite.dtb
dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-pine64-star64.dtb
dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
diff --git a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
new file mode 100644
index 000000000000..e110146f0b76
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
@@ -0,0 +1,176 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 E Shattow <e@...eshell.de>
+ */
+
+/dts-v1/;
+#include <dt-bindings/pinctrl/starfive,jh7110-pinctrl.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "jh7110-common.dtsi"
+
+/ {
+ model = "Milk-V Mars CM Lite";
+ compatible = "milkv,marscm-lite", "starfive,jh7110";
+
+ aliases {
+ i2c1 = &i2c1;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ serial3 = &uart3;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&sysgpio 33 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&gmac0 {
+ assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+ assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+ starfive,tx-use-rgmii-clk;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c6 {
+ status = "disabled";
+};
+
+&mmc0 {
+ bus-width = <4>;
+ cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+};
+
+&mmc0_pins {
+ pwren-pins {
+ pinmux = <GPIOMUX(22, GPOUT_HIGH,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ };
+};
+
+&mmc1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ status = "okay";
+
+ ap6256: wifi@1 {
+ compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+ interrupt-parent = <&sysgpio>;
+ interrupts = <34 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+ pinctrl-0 = <&wifi_host_wake_irq>;
+ pinctrl-names = "default";
+ };
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&phy0 {
+ rx-internal-delay-ps = <1500>;
+ tx-internal-delay-ps = <1500>;
+ motorcomm,rx-clk-drv-microamp = <3970>;
+ motorcomm,rx-data-drv-microamp = <2910>;
+ motorcomm,tx-clk-10-inverted;
+ motorcomm,tx-clk-100-inverted;
+ motorcomm,tx-clk-1000-inverted;
+ motorcomm,tx-clk-adj-enabled;
+};
+
+&pwm {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+};
+
+&sysgpio {
+ uart1_pins: uart1-0 {
+ tx-pins {
+ pinmux = <GPIOMUX(16, GPOUT_SYS_UART1_TX,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-disable;
+ drive-strength = <12>;
+ input-disable;
+ input-schmitt-disable;
+ };
+
+ rx-pins {
+ pinmux = <GPIOMUX(17, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_SYS_UART1_RX)>;
+ bias-pull-up;
+ input-enable;
+ input-schmitt-enable;
+ };
+
+ cts-pins {
+ pinmux = <GPIOMUX(3, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_SYS_UART1_CTS)>;
+ bias-disable;
+ input-enable;
+ input-schmitt-enable;
+ };
+
+ rts-pins {
+ pinmux = <GPIOMUX(2, GPOUT_SYS_UART1_RTS,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-disable;
+ input-disable;
+ input-schmitt-disable;
+ };
+ };
+
+ usb0_pins: usb0-0 {
+ vbus-pins {
+ pinmux = <GPIOMUX(25, GPOUT_SYS_USB_DRIVE_VBUS,
+ GPOEN_ENABLE,
+ GPI_NONE)>;
+ bias-disable;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
+ wifi_host_wake_irq: wifi-host-wake-irq {
+ wake-pins {
+ pinmux = <GPIOMUX(34, GPOUT_LOW,
+ GPOEN_DISABLE,
+ GPI_NONE)>;
+ input-enable;
+ };
+ };
+};
+
+&uart1 {
+ uart-has-rtscts;
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb0 {
+ dr_mode = "host";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pins>;
+ status = "okay";
+};
--
2.50.0
Powered by blists - more mailing lists