Message-ID: <20250819053205.9976-3-mike.looijmans@topic.nl>
Date: Tue, 19 Aug 2025 07:31:15 +0200
From: Mike Looijmans <mike.looijmans@...ic.nl>
To: dri-devel@...ts.freedesktop.org
CC: Mike Looijmans <mike.looijmans@...ic.nl>,
	Andrzej Hajda <andrzej.hajda@...el.com>,
	David Airlie <airlied@...il.com>,
	Jernej Skrabec <jernej.skrabec@...il.com>,
	Jonas Karlman <jonas@...boo.se>,
	Laurent Pinchart <Laurent.pinchart@...asonboard.com>,
	Maarten Lankhorst <maarten.lankhorst@...ux.intel.com>,
	Maxime Ripard <mripard@...nel.org>,
	Neil Armstrong <neil.armstrong@...aro.org>,
	Robert Foss <rfoss@...nel.org>,
	Simona Vetter <simona@...ll.ch>,
	Thomas Zimmermann <tzimmermann@...e.de>,
	linux-kernel@...r.kernel.org
Subject: [PATCH v2 2/2] drm: bridge: Add TI tmds181 and sn65dp159 driver

The tmds181 and sn65dp159 are "retimers" and hence can be considered
HDMI-to-HDMI bridges. Typical usage is to convert the output of an
FPGA into a valid HDMI signal, and it will typically be inserted
between an encoder and hdmi-connector.

Signed-off-by: Mike Looijmans <mike.looijmans@...ic.nl>
---

Changes in v2:
Use atomic_enable/disable
Use #defines for bit fields in registers
Allow HDMI 2 compliance
Filter modes on clock range
Use cross-over pixel frequency instead of manual overides
Devicetree bindings according to standards

 drivers/gpu/drm/bridge/Kconfig      |  11 +
 drivers/gpu/drm/bridge/Makefile     |   1 +
 drivers/gpu/drm/bridge/ti-tmds181.c | 561 ++++++++++++++++++++++++++++
 3 files changed, 573 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/ti-tmds181.c

diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index b9e0ca85226a..753177fc9b50 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -430,6 +430,17 @@ config DRM_TI_SN65DSI86
 	help
 	  Texas Instruments SN65DSI86 DSI to eDP Bridge driver
 
+config DRM_TI_TMDS181
+        tristate "TI TMDS181 and SN65DP159 HDMI retimer bridge driver"
+	depends on OF
+	select DRM_KMS_HELPER
+	select REGMAP_I2C
+	help
+	  Enable this to support the TI TMDS181 and SN65DP159 HDMI retimers.
+	  The SN65DP159 provides output into a cable (source) whereas the
+	  TMDS181 is meant to forward a cable signal into a PCB (sink). Either
+	  can be set up as source or sink though.
+
 config DRM_TI_TPD12S015
 	tristate "TI TPD12S015 HDMI level shifter and ESD protection"
 	depends on OF
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 245e8a27e3fc..f4b5089e903c 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -39,6 +39,7 @@ obj-$(CONFIG_DRM_TI_SN65DSI83) += ti-sn65dsi83.o
 obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
 obj-$(CONFIG_DRM_TI_TDP158) += ti-tdp158.o
 obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
+obj-$(CONFIG_DRM_TI_TMDS181) += ti-tmds181.o
 obj-$(CONFIG_DRM_TI_TPD12S015) += ti-tpd12s015.o
 obj-$(CONFIG_DRM_NWL_MIPI_DSI) += nwl-dsi.o
 obj-$(CONFIG_DRM_ITE_IT66121) += ite-it66121.o
diff --git a/drivers/gpu/drm/bridge/ti-tmds181.c b/drivers/gpu/drm/bridge/ti-tmds181.c
new file mode 100644
index 000000000000..34cbdb066820
--- /dev/null
+++ b/drivers/gpu/drm/bridge/ti-tmds181.c
@@ -0,0 +1,561 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * TI tmds181 and sn65dp159 HDMI redriver and retimer chips
+ *
+ * Copyright (C) 2018 - 2025 Topic Embedded Products <www.topic.nl>
+ *
+ * based on code
+ * Copyright (C) 2007 Hans Verkuil
+ * Copyright (C) 2016, 2017 Leon Woestenberg <leon@...ebranch.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_print.h>
+#include <drm/drm_probe_helper.h>
+
+MODULE_DESCRIPTION("I2C device driver for DP159 and TMDS181 redriver/retimer");
+MODULE_AUTHOR("Mike Looijmans");
+MODULE_LICENSE("GPL");
+
+#define TMDS181_REG_ID		0
+#define TMDS181_REG_REV		0x8
+#define TMDS181_REG_CTRL9	0x9
+/* Registers A and B have a volatile bit, but we don't use it, so cache is ok */
+#define TMDS181_REG_CTRLA	0xA
+#define TMDS181_REG_CTRLB	0xB
+#define TMDS181_REG_CTRLC	0xC
+#define TMDS181_REG_EQUALIZER	0xD
+#define TMDS181_REG_EYESCAN	0xE
+
+#define TMDS181_CTRL9_SIG_EN			BIT(4)
+#define TMDS181_CTRL9_PD_EN			BIT(3)
+#define TMDS181_CTRL9_HPD_AUTO_PWRDWN_DISABLE	BIT(2)
+#define TMDS181_CTRL9_I2C_DR_CTL		GENMASK(1, 0)
+
+#define TMDS181_CTRLA_MODE_SINK			BIT(7)
+#define TMDS181_CTRLA_HPDSNK_GATE_EN		BIT(6)
+#define TMDS181_CTRLA_EQ_ADA_EN			BIT(5)
+#define TMDS181_CTRLA_EQ_EN			BIT(4)
+#define TMDS181_CTRLA_AUX_BRG_EN		BIT(3)
+#define TMDS181_CTRLA_APPLY			BIT(2)
+#define TMDS181_CTRLA_DEV_FUNC_MODE		GENMASK(1, 0)
+
+#define TMDS181_CTRLB_SLEW_CTL			GENMASK(7, 6)
+#define TMDS181_CTRLB_HDMI_SEL_DVI		BIT(5)
+#define TMDS181_CTRLB_TX_TERM_CTL		GENMASK(4, 3)
+#define TMDS181_CTRLB_DDC_DR_SEL		BIT(2)
+#define TMDS181_CTRLB_TMDS_CLOCK_RATIO_STATUS	BIT(1)
+#define TMDS181_CTRLB_DDC_TRAIN_SET		BIT(0)
+
+#define TMDS181_CTRLB_TX_TERM_150_300_OHMS	1
+#define TMDS181_CTRLB_TX_TERM_75_150_OHMS	3
+
+#define TMDS181_CTRLC_VSWING_DATA		GENMASK(7, 5)
+#define TMDS181_CTRLC_VSWING_CLK		GENMASK(4, 2)
+#define TMDS181_CTRLC_HDMI_TWPST1		GENMASK(1, 0)
+
+#define TMDS181_EQ_DATA_LANE			GENMASK(5, 3)
+#define TMDS181_EQ_CLOCK_LANE			GENMASK(2, 1)
+#define TMDS181_EQ_DIS_HDMI2_SWG		BIT(0)
+
+/* Above this data rate HDMI2 standards apply (TX termination) */
+#define HDMI2_PIXEL_RATE_KHZ	340000
+
+enum tmds181_chip {
+	tmds181,
+	dp159,
+};
+
+struct tmds181_data {
+	struct i2c_client *client;
+	struct regmap *regmap;
+	struct drm_bridge *next_bridge;
+	struct drm_bridge bridge;
+	u32 retimer_threshold_khz;
+	enum tmds181_chip chip;
+};
+
+static inline struct tmds181_data *
+drm_bridge_to_tmds181_data(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct tmds181_data, bridge);
+}
+
+/* Set "apply" bit in control register after making changes */
+static int tmds181_apply_changes(struct tmds181_data *data)
+{
+	return regmap_write_bits(data->regmap, TMDS181_REG_CTRLA,
+				 TMDS181_CTRLA_APPLY, TMDS181_CTRLA_APPLY);
+}
+
+static int tmds181_attach(struct drm_bridge *bridge,
+			  enum drm_bridge_attach_flags flags)
+{
+	struct tmds181_data *data = drm_bridge_to_tmds181_data(bridge);
+
+	return drm_bridge_attach(bridge->encoder, data->next_bridge, bridge,
+				 flags);
+}
+
+static enum drm_mode_status
+tmds181_mode_valid(struct drm_bridge *bridge, const struct drm_display_info *info,
+		   const struct drm_display_mode *mode)
+{
+	/* Clock limits: clk between 25 and 350 MHz, clk is 1/10 of bit clock */
+	if (mode->clock < 25000)
+		return MODE_CLOCK_LOW;
+
+	/* The actual HDMI clock (if provided) cannot exceed 350MHz */
+	if (mode->crtc_clock > 350000)
+		return MODE_CLOCK_HIGH;
+
+	/*
+	 * When in HDMI 2 mode, the clock is 1/40th of the bitrate. The limit is
+	 * then the data rate of 6Gbps, which would use a 600MHz pixel clock.
+	 */
+	if (mode->clock > 600000)
+		return MODE_CLOCK_HIGH;
+
+	return MODE_OK;
+}
+
+static void tmds181_enable(struct drm_bridge *bridge, struct drm_bridge_state *old_bridge_state)
+{
+	struct tmds181_data *data = drm_bridge_to_tmds181_data(bridge);
+	struct drm_atomic_state *state = old_bridge_state->base.state;
+	const struct drm_bridge_state *bridge_state;
+	const struct drm_crtc_state *crtc_state;
+	const struct drm_display_mode *mode;
+	struct drm_connector *connector;
+	struct drm_crtc *crtc;
+	unsigned int val;
+
+	/*
+	 * Retrieve the CRTC adjusted mode. This requires a little dance to go
+	 * from the bridge to the encoder, to the connector and to the CRTC.
+	 */
+	connector = drm_atomic_get_new_connector_for_encoder(state,
+							     bridge->encoder);
+	crtc = drm_atomic_get_new_connector_state(state, connector)->crtc;
+	crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
+	mode = &crtc_state->adjusted_mode;
+
+	/* Set retimer/redriver mode based on pixel clock */
+	val = mode->clock > data->retimer_threshold_khz ? TMDS181_CTRLA_DEV_FUNC_MODE : 0;
+	regmap_update_bits(data->regmap, TMDS181_REG_CTRLA,
+			   TMDS181_CTRLA_DEV_FUNC_MODE, val);
+
+	/* Configure TX termination based on pixel clock */
+	val = mode->clock > HDMI2_PIXEL_RATE_KHZ ?
+				TMDS181_CTRLB_TX_TERM_75_150_OHMS :
+				TMDS181_CTRLB_TX_TERM_150_300_OHMS;
+	regmap_update_bits(data->regmap, TMDS181_REG_CTRLB,
+			   TMDS181_CTRLB_TX_TERM_CTL,
+			   FIELD_PREP(TMDS181_CTRLB_TX_TERM_CTL, val));
+
+	regmap_update_bits(data->regmap, TMDS181_REG_CTRL9,
+			   TMDS181_CTRL9_PD_EN, 0);
+}
+
+static void tmds181_disable(struct drm_bridge *bridge, struct drm_bridge_state *old_bridge_state)
+{
+	struct tmds181_data *data = drm_bridge_to_tmds181_data(bridge);
+
+	/* Set the PD_EN bit */
+	regmap_update_bits(data->regmap, TMDS181_REG_CTRL9,
+			   TMDS181_CTRL9_PD_EN, TMDS181_CTRL9_PD_EN);
+}
+
+static const struct drm_bridge_funcs tmds181_bridge_funcs = {
+	.attach		= tmds181_attach,
+	.mode_valid	= tmds181_mode_valid,
+	.atomic_enable	= tmds181_enable,
+	.atomic_disable	= tmds181_disable,
+
+	.atomic_reset = drm_atomic_helper_bridge_reset,
+	.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+};
+
+static const char * const tmds181_modes[] = {
+	"redriver",
+	"auto1",
+	"auto2",
+	"retimer",
+};
+
+static ssize_t mode_show(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct tmds181_data *data = dev_get_drvdata(dev);
+	const char *equalizer;
+	u32 val;
+	int ret;
+
+	ret = regmap_read(data->regmap, TMDS181_REG_CTRLA, &val);
+	if (ret < 0)
+		return ret;
+
+	if (val & BIT(4)) {
+		if (val & BIT(5))
+			equalizer = "eq-adaptive";
+		else
+			equalizer = "eq-fixed";
+	} else {
+		equalizer = "eq-disabled";
+	}
+
+	return scnprintf(buf, PAGE_SIZE, "%6s %s %s\n",
+			(val & BIT(7)) ? "sink" : "source",
+			tmds181_modes[val & 0x03],
+			equalizer);
+}
+
+static ssize_t mode_store(struct device *dev, struct device_attribute *attr,
+			  const char *buf, size_t len)
+{
+	struct tmds181_data *data = dev_get_drvdata(dev);
+	u32 val;
+	int ret;
+	int i;
+
+	/* Strip trailing newline(s) for being user friendly */
+	while (len && buf[len] == '\n')
+		--len;
+
+	/* Need at least 4 actual characters */
+	if (len < 4)
+		return -EINVAL;
+
+	ret = regmap_read(data->regmap, TMDS181_REG_CTRLA, &val);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < ARRAY_SIZE(tmds181_modes); ++i) {
+		if (strncmp(tmds181_modes[i], buf, len) == 0) {
+			val &= ~TMDS181_CTRLA_DEV_FUNC_MODE;
+			val |= FIELD_PREP(TMDS181_CTRLA_DEV_FUNC_MODE, i);
+			break;
+		}
+	}
+
+	if (strncmp("sink", buf, len) == 0)
+		val |= TMDS181_CTRLA_MODE_SINK;
+
+	if (strncmp("source", buf, len) == 0)
+		val &= ~TMDS181_CTRLA_MODE_SINK;
+
+	if (strncmp("eq-", buf, 3) == 0) {
+		switch (buf[3]) {
+		case 'a': /* adaptive */
+			val |= TMDS181_CTRLA_EQ_ADA_EN | TMDS181_CTRLA_EQ_EN;
+			break;
+		case 'f': /* fixed */
+			val |= TMDS181_CTRLA_EQ_EN;
+			val &= ~TMDS181_CTRLA_EQ_ADA_EN;
+			break;
+		case 'd': /* disable */
+			val &= ~(TMDS181_CTRLA_EQ_ADA_EN | TMDS181_CTRLA_EQ_EN);
+			break;
+		}
+	}
+
+	/* Always set the "apply changes" bit */
+	val |= TMDS181_CTRLA_APPLY;
+
+	ret = regmap_write(data->regmap, TMDS181_REG_CTRLA, val);
+	if (ret < 0)
+		return ret;
+
+	return len;
+}
+
+/* termination for HDMI TX: 0=off, 1=150..300, 3=75..150 ohms */
+static ssize_t termination_show(struct device *dev,
+		struct device_attribute *attr, char *buf)
+{
+	struct tmds181_data *data = dev_get_drvdata(dev);
+	u32 val;
+	int ret;
+
+	ret = regmap_read(data->regmap, TMDS181_REG_CTRLB, &val);
+	if (ret < 0)
+		return ret;
+
+	return scnprintf(buf, PAGE_SIZE, "%u\n",
+			 FIELD_GET(TMDS181_CTRLB_TX_TERM_CTL, val));
+}
+
+static ssize_t termination_store(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t len)
+{
+	struct tmds181_data *data = dev_get_drvdata(dev);
+	u32 val;
+	unsigned long newval;
+	int ret;
+
+	ret = regmap_read(data->regmap, TMDS181_REG_CTRLB, &val);
+	if (ret < 0)
+		return ret;
+
+	ret = kstrtoul((const char *) buf, 10, &newval);
+	if (ret)
+		return ret;
+
+	if (newval > 3)
+		return -EINVAL;
+
+	val &= ~TMDS181_CTRLB_TX_TERM_CTL;
+	val |= FIELD_PREP(TMDS181_CTRLB_TX_TERM_CTL, newval);
+
+	ret = regmap_write(data->regmap, TMDS181_REG_CTRLB, val);
+	if (ret < 0)
+		return ret;
+
+	return len;
+}
+
+static DEVICE_ATTR_RW(mode);
+static DEVICE_ATTR_RW(termination);
+
+static struct attribute *tmds181_attrs[] = {
+	&dev_attr_mode.attr,
+	&dev_attr_termination.attr,
+	NULL,
+};
+
+static const struct attribute_group tmds181_attr_group = {
+	.attrs = tmds181_attrs,
+};
+
+static const u8 tmds181_id_tmds181[8] __nonstring = "TMDS181 ";
+static const u8 tmds181_id_dp159[8]   __nonstring = "DP159   ";
+
+static int tmds181_check_id(struct tmds181_data *data)
+{
+	int ret;
+	int retry;
+	u8 buffer[8];
+
+	for (retry = 0; retry < 20; ++retry) {
+		ret = regmap_bulk_read(data->regmap, TMDS181_REG_ID, buffer,
+				       sizeof(buffer));
+		if (!ret)
+			break;
+
+		/* Compensate for very long OE power-up delays due to the cap */
+		usleep_range(5000, 10000);
+	}
+
+	if (ret) {
+		dev_err(&data->client->dev, "I2C read ID failed\n");
+		return ret;
+	}
+
+	if (memcmp(buffer, tmds181_id_tmds181, sizeof(buffer)) == 0) {
+		dev_info(&data->client->dev, "Detected: TMDS181\n");
+		data->chip = tmds181;
+		return 0;
+	}
+
+	if (memcmp(buffer, tmds181_id_dp159, sizeof(buffer)) == 0) {
+		dev_info(&data->client->dev, "Detected: DP159\n");
+		data->chip = dp159;
+		return 0;
+	}
+
+	dev_err(&data->client->dev, "Unknown ID: %*pE\n", (int)sizeof(buffer), buffer);
+
+	return -ENODEV;
+}
+
+static bool tmds181_regmap_is_volatile(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	/* IBERT result and status registers, not used yet */
+	case 0x15:
+	case 0x17 ... 0x1F:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static const struct regmap_config tmds181_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.cache_type = REGCACHE_RBTREE,
+	.max_register = 0x20,
+	.volatile_reg = tmds181_regmap_is_volatile,
+};
+
+static int tmds181_probe(struct i2c_client *client)
+{
+	struct tmds181_data *data;
+	struct gpio_desc *oe_gpio;
+	int ret;
+	u32 param;
+	u8 val;
+
+	/* Check if the adapter supports the needed features */
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+		return -EIO;
+
+	data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->client = client;
+	i2c_set_clientdata(client, data);
+	data->regmap = devm_regmap_init_i2c(client, &tmds181_regmap_config);
+	if (IS_ERR(data->regmap))
+		return PTR_ERR(data->regmap);
+
+	/* The "OE" pin acts as a reset */
+	oe_gpio = devm_gpiod_get_optional(&client->dev, "oe", GPIOD_OUT_LOW);
+	if (IS_ERR(oe_gpio)) {
+		ret = PTR_ERR(oe_gpio);
+		if (ret != -EPROBE_DEFER)
+			dev_err(&client->dev, "failed to acquire 'oe' gpio\n");
+		return ret;
+	}
+	if (oe_gpio) {
+		/* Need at least 100us reset pulse */
+		usleep_range(100, 200);
+		gpiod_set_value_cansleep(oe_gpio, 1);
+	}
+
+	/* Reading the ID also provides enough time for the reset */
+	ret = tmds181_check_id(data);
+	if (ret)
+		return ret;
+
+	/*
+	 * We take care of power control, so disable the chips PM functions, and
+	 * allow the DDC to run at 400kHz
+	 */
+	regmap_update_bits(data->regmap, TMDS181_REG_CTRL9,
+			TMDS181_CTRL9_SIG_EN | TMDS181_CTRL9_PD_EN |
+			TMDS181_CTRL9_HPD_AUTO_PWRDWN_DISABLE |
+			TMDS181_CTRL9_I2C_DR_CTL,
+			TMDS181_CTRL9_PD_EN |
+			TMDS181_CTRL9_HPD_AUTO_PWRDWN_DISABLE |
+			TMDS181_CTRL9_I2C_DR_CTL);
+
+	/* Apply configuration changes */
+	if (of_property_read_bool(client->dev.of_node, "source-mode"))
+		regmap_update_bits(data->regmap, TMDS181_REG_CTRLA,
+				   TMDS181_CTRLA_MODE_SINK, 0);
+	if (of_property_read_bool(client->dev.of_node, "sink-mode"))
+		regmap_update_bits(data->regmap, TMDS181_REG_CTRLA,
+				   TMDS181_CTRLA_MODE_SINK, TMDS181_CTRLA_MODE_SINK);
+
+	/*
+	 * Using the automatic modes of the chip uses considerable power as it
+	 * will keep the PLL running at all times. So instead, define our own
+	 * threshold for the pixel rate. This also allows to use a sane default
+	 * of 200MHz pixel rate for the redriver-retimer crossover point, as the
+	 * modes below 3k don't show any benefit from the retimer.
+	 */
+	data->retimer_threshold_khz = 200000;
+	if (!of_property_read_u32(client->dev.of_node,
+				  "ti,retimer-threshold-hz", &param))
+		data->retimer_threshold_khz = param / 1000;
+
+	/* Default to low-power redriver mode */
+	regmap_update_bits(data->regmap, TMDS181_REG_CTRLA,
+			   TMDS181_CTRLA_DEV_FUNC_MODE, 0x00);
+
+	if (of_property_read_bool(client->dev.of_node, "ti,adaptive-equalizer"))
+		regmap_update_bits(data->regmap, TMDS181_REG_CTRLA,
+				   TMDS181_CTRLA_EQ_EN | TMDS181_CTRLA_EQ_ADA_EN,
+				   TMDS181_CTRLA_EQ_EN | TMDS181_CTRLA_EQ_ADA_EN);
+	if (of_property_read_bool(client->dev.of_node, "ti,disable-equalizer"))
+		regmap_update_bits(data->regmap, TMDS181_REG_CTRLA,
+				   TMDS181_CTRLA_EQ_EN | TMDS181_CTRLA_EQ_ADA_EN,
+				   0);
+
+	switch (data->chip) {
+	case dp159:
+		val = 0;
+		if (!of_property_read_u32(client->dev.of_node,
+					"slew-rate", &param)) {
+			if (param > 3) {
+				dev_err(&client->dev, "invalid slew-rate\n");
+				return -EINVAL;
+			}
+			/* Implement 0 = slow, 3 = fast slew rate */
+			val = FIELD_PREP(TMDS181_CTRLB_SLEW_CTL, (3 - param));
+		}
+		if (of_property_read_bool(client->dev.of_node, "ti,dvi-mode"))
+			val |= TMDS181_CTRLB_HDMI_SEL_DVI;
+		break;
+	default:
+		val = TMDS181_CTRLB_DDC_DR_SEL;
+		break;
+	}
+
+	/* Default to low-speed termination */
+	val |= FIELD_PREP(TMDS181_CTRLB_TX_TERM_CTL, TMDS181_CTRLB_TX_TERM_150_300_OHMS);
+
+	ret = regmap_write(data->regmap, TMDS181_REG_CTRLB, val);
+	if (ret < 0) {
+		dev_err(&client->dev, "regmap_write(B) failed\n");
+		return ret;
+	}
+
+	ret = sysfs_create_group(&client->dev.kobj, &tmds181_attr_group);
+	if (ret)
+		dev_err(&client->dev, "sysfs_create_group error: %d\n", ret);
+
+	/* Find next bridge in chain */
+	data->next_bridge = devm_drm_of_get_bridge(&client->dev, client->dev.of_node, 1, 0);
+	if (IS_ERR(data->next_bridge))
+		return dev_err_probe(&client->dev, PTR_ERR(data->next_bridge),
+				     "Failed to find next bridge\n");
+
+	/* Register the bridge. */
+	data->bridge.funcs = &tmds181_bridge_funcs;
+	data->bridge.of_node = client->dev.of_node;
+
+	return devm_drm_bridge_add(&client->dev, &data->bridge);
+}
+
+static const struct i2c_device_id tmds181_id[] = {
+	{ "tmds181", tmds181 },
+	{ "sn65dp159", dp159 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, tmds181_id);
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id tmds181_of_match[] = {
+	{ .compatible = "ti,tmds181", },
+	{ .compatible = "ti,sn65dp159", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, tmds181_of_match);
+#endif
+
+static struct i2c_driver tmds181_driver = {
+	.driver = {
+		.owner = THIS_MODULE,
+		.name	= "tmds181",
+		.of_match_table = of_match_ptr(tmds181_of_match),
+	},
+	.probe		= tmds181_probe,
+	.id_table	= tmds181_id,
+};
+
+module_i2c_driver(tmds181_driver);
-- 
2.43.0


Met vriendelijke groet / kind regards,

Mike Looijmans
System Expert


TOPIC Embedded Products B.V.
Materiaalweg 4, 5681 RJ Best
The Netherlands

T: +31 (0) 499 33 69 69
E: mike.looijmans@...ic.nl
W: www.topic.nl

Please consider the environment before printing this e-mail

Powered by blists - more mailing lists