[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <CAMuHMdVb_5+gVDCUYYZ2Xj55gXzZATx+5vaY6uS1TuCNYb9Qeg@mail.gmail.com>
Date: Wed, 3 Sep 2025 17:04:15 +0200
From: Geert Uytterhoeven <geert@...ux-m68k.org>
To: Prabhakar <prabhakar.csengg@...il.com>
Cc: Magnus Damm <magnus.damm@...il.com>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>, Conor Dooley <conor+dt@...nel.org>,
linux-renesas-soc@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, Biju Das <biju.das.jz@...renesas.com>,
Fabrizio Castro <fabrizio.castro.jz@...esas.com>,
Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>
Subject: Re: [PATCH 6/6] arm64: dts: renesas: rzt2h-n2h-evk: Enable USB2.0 support
Hi Prabhakar,
On Thu, 21 Aug 2025 at 18:19, Prabhakar <prabhakar.csengg@...il.com> wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>
>
> Enable USB2.0 support on RZ/T2H and RZ/N2H EVKs.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@...renesas.com>
Thanks for your patch!
> --- a/arch/arm64/boot/dts/renesas/r9a09g077m44-rzt2h-evk.dts
> +++ b/arch/arm64/boot/dts/renesas/r9a09g077m44-rzt2h-evk.dts
> @@ -29,6 +29,28 @@
> */
> #define SD1_MICRO_SD 1
>
> +/*
> + * USB Pin Configuration:
> + *
> + * This board is equipped with three USB connectors: Type-A (CN80), Mini-B (CN79),
> + * and Micro-AB (CN33). The RZ/T2H SoC has a single USB channel, so either the USB
> + * host interface or the USB function interface can be used, but not both at the
> + * same time.
Please reflow the text to fit in 80 columns.
The last sentence applies to the CN80 and CN79 connectors only, right?
> + *
> + * By default, the Type-A (CN80) and Mini-B (CN79) connectors are enabled.
> + * Configure the switches as follows:
> + * - P00_0 - P00_2 (control signals for USB power supply): SW1[5] = ON
> + * - USB_VBUSIN (used for USB function): SW7[7] = OFF; SW7[8] = ON
> + * - USB_VBUSEN (used for USB_HF_VBUSEN): SW7[9] = OFF; SW7[10] = ON
> + *
> + * To enable the Micro-AB (CN33) USB OTG connector, set the following macro to 1
> + * and configure the switches as follows:
> + * - P00_0 - P00_2 (control signals for USB power supply): SW1[5] = ON
> + * - USB_VBUSIN (used for USB OTG): SW7[7] = ON; SW7[8] = OFF
> + * - USB_VBUSEN (used for USB_OTG_VBUSEN): SW7[9] = ON; SW7[10] = OFF
> + */
> +#define USB_OTG 0
> +
> #include "rzt2h-n2h-evk-common.dtsi"
>
> / {
> @@ -145,4 +167,18 @@ i2c1_pins: i2c1-pins {
> pinmux = <RZT2H_PORT_PINMUX(5, 0, 0x17)>, /* SDA */
> <RZT2H_PORT_PINMUX(4, 7, 0x17)>; /* SCL */
> };
> +
> +#if USB_OTG
> + usb-exicen-hog {
> + gpio-hog;
> + gpios = <RZT2H_GPIO(0, 2) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "usb_exicen_a";
> + };
> +#endif
> +
> + usb_pins: usb-pins {
> + pinmux = <RZT2H_PORT_PINMUX(0, 0, 0x13)>, /* VBUS */
s/VBUS/VBUSEN/?
> + <RZT2H_PORT_PINMUX(0, 1, 0x13)>; /* OVRCUR */
> + };
> };
> diff --git a/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts b/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts
> index 80f358fb2d74..b98b0f7c1128 100644
> --- a/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts
> +++ b/arch/arm64/boot/dts/renesas/r9a09g087m44-rzn2h-evk.dts
> @@ -33,6 +33,33 @@
> */
> #define SD1_MICRO_SD 1
>
> +/*
> + * USB Pin Configuration:
> + *
> + * This board is equipped with three USB connectors: Type-A (CN7), Mini-B (CN8),
> + * and Micro-AB (CN9). The RZ/N2H SoC has a single USB channel, so either the USB
> + * host interface or the USB function interface can be used, but not both at the
> + * same time.
Please reflow the text to fit in 80 columns.
The last sentence applies to the CN7 and CN8 connectors only, right?
> + *
> + * By default, the Type-A (CN7) and Mini-B (CN8) connectors are enabled.
> + * Configure the switches as follows:
> + * - P02_2 - P02_3 (control signals for USB power supply): DSW2[6] = OFF;
s/DSW2[6]/DSW2[5]/?
> + * - P02_2 (used for VBUSEN): DSW14[5] = OFF; DSW14[6] = ON
> + * - P02_3 (used for USB_OVRCUR): DSW14[1] = OFF; DSW14[2] = ON
> + * - USB_VBUSIN (used for VBUS of CN8 for function): DSW16[1] = OFF; DSW16[2] = ON
> + * - USB_VBUSEN (used for USB_HF_VBUSEN): DSW16[3] = OFF; DSW16[4] = ON
> + *
> + * To enable the Micro-AB (CN9) USB OTG connector, set the following macro to 1
> + * and configure the switches as follows:
> + * - P02_2 - P02_3 (control signals for USB power supply): DSW2[6] = OFF;
s/DSW2[6]/DSW2[5]/?
> + * - P02_2 (used for VBUSEN): DSW14[5] = OFF; DSW14[6] = ON
> + * - P02_3 (used for USB_OVRCUR): DSW14[1] = OFF; DSW14[2] = ON
> + * - USB_VBUSIN (used for VBUS of CN9 for OTG): DSW16[1] = ON; DSW16[2] = OFF
> + * - USB_VBUSEN (used for USB_OTG_VBUSEN): DSW16[3] = ON; DSW16[4] = OFF
> + * - USB_EXICEN (used for USB OTG EXICEN): DSW14[3] = OFF; DSW14[4] = ON
Looks like you could use P00_0 - P00_2 instead of P02_2 - P02_3, like
on the RZ/T2H EVK?
But you don't want to do that because you want to use these pins for Ethernet?
> + */
> +#define USB_OTG 0
> +
> #include "rzt2h-n2h-evk-common.dtsi"
>
> /*
> @@ -185,4 +212,18 @@ i2c1_pins: i2c1-pins {
> pinmux = <RZT2H_PORT_PINMUX(3, 3, 0x17)>,
> <RZT2H_PORT_PINMUX(3, 4, 0x17)>;
> };
> +
> +#if USB_OTG
> + usb-exicen-hog {
> + gpio-hog;
> + gpios = <RZT2H_GPIO(2, 4) GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "usb_exicen_a";
> + };
> +#endif
> +
> + usb_pins: usb-pins {
> + pinmux = <RZT2H_PORT_PINMUX(2, 2, 0x13)>, /* VBUS */
s/VBUS/VBUSEN/?
> + <RZT2H_PORT_PINMUX(2, 3, 0x13)>; /* OVRCUR */
> + };
> };
The rest LGTM.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@...ux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Powered by blists - more mailing lists