[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <aLhssUQa7tvUfu2j@hu-wasimn-hyd.qualcomm.com>
Date: Wed, 3 Sep 2025 21:58:33 +0530
From: Wasim Nazir <wasim.nazir@....qualcomm.com>
To: Konrad Dybcio <konrad.dybcio@....qualcomm.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@....qualcomm.com>,
Ulf Hansson <ulf.hansson@...aro.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>,
Richard Cochran <richardcochran@...il.com>, kernel@....qualcomm.com,
linux-mmc@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-msm@...r.kernel.org,
netdev@...r.kernel.org, Monish Chunara <quic_mchunara@...cinc.com>
Subject: Re: [PATCH 2/5] arm64: dts: qcom: lemans: Add SDHC controller and
SDC pin configuration
On Wed, Sep 03, 2025 at 06:12:59PM +0200, Konrad Dybcio wrote:
> On 8/27/25 3:20 AM, Dmitry Baryshkov wrote:
> > On Tue, Aug 26, 2025 at 11:51:01PM +0530, Wasim Nazir wrote:
> >> From: Monish Chunara <quic_mchunara@...cinc.com>
> >>
> >> Introduce the SDHC v5 controller node for the Lemans platform.
> >> This controller supports either eMMC or SD-card, but only one
> >> can be active at a time. SD-card is the preferred configuration
> >> on Lemans targets, so describe this controller.
> >>
> >> Define the SDC interface pins including clk, cmd, and data lines
> >> to enable proper communication with the SDHC controller.
> >>
> >> Signed-off-by: Monish Chunara <quic_mchunara@...cinc.com>
> >> Co-developed-by: Wasim Nazir <wasim.nazir@....qualcomm.com>
> >> Signed-off-by: Wasim Nazir <wasim.nazir@....qualcomm.com>
> >> ---
> >> arch/arm64/boot/dts/qcom/lemans.dtsi | 70 ++++++++++++++++++++++++++++++++++++
> >> 1 file changed, 70 insertions(+)
> >>
> >> diff --git a/arch/arm64/boot/dts/qcom/lemans.dtsi b/arch/arm64/boot/dts/qcom/lemans.dtsi
> >> index 99a566b42ef2..a5a3cdba47f3 100644
> >> --- a/arch/arm64/boot/dts/qcom/lemans.dtsi
> >> +++ b/arch/arm64/boot/dts/qcom/lemans.dtsi
> >> @@ -3834,6 +3834,36 @@ apss_tpdm2_out: endpoint {
> >> };
> >> };
> >>
> >> + sdhc: mmc@...4000 {
> >> + compatible = "qcom,sa8775p-sdhci", "qcom,sdhci-msm-v5";
> >> + reg = <0x0 0x087c4000 0x0 0x1000>;
> >> +
> >> + interrupts = <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 521 IRQ_TYPE_LEVEL_HIGH>;
> >> + interrupt-names = "hc_irq", "pwr_irq";
> >> +
> >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> >> + <&gcc GCC_SDCC1_APPS_CLK>;
> >> + clock-names = "iface", "core";
> >> +
> >> + interconnects = <&aggre1_noc MASTER_SDC 0 &mc_virt SLAVE_EBI1 0>,
> >> + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDC1 0>;
> >> + interconnect-names = "sdhc-ddr", "cpu-sdhc";
> >> +
> >> + iommus = <&apps_smmu 0x0 0x0>;
> >> + dma-coherent;
> >> +
> >> + resets = <&gcc GCC_SDCC1_BCR>;
> >> +
> >> + no-sdio;
> >> + no-mmc;
> >> + bus-width = <4>;
> >
> > This is the board configuration, it should be defined in the EVK DTS.
>
> Unless the controller is actually incapable of doing non-SDCards
>
> But from the limited information I can find, this one should be able
> to do both
>
It’s doable, but the bus width differs when this controller is used for
eMMC, which is supported on the Mezz board. So, it’s cleaner to define
only what’s needed for each specific usecase on the board.
--
Regards,
Wasim
Powered by blists - more mailing lists