[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <7234085c-55b6-4131-acb8-a4ec097c6668@oss.qualcomm.com>
Date: Wed, 3 Sep 2025 19:16:50 +0200
From: Konrad Dybcio <konrad.dybcio@....qualcomm.com>
To: Wasim Nazir <wasim.nazir@....qualcomm.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@....qualcomm.com>,
Ulf Hansson <ulf.hansson@...aro.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley
<conor+dt@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>,
Richard Cochran <richardcochran@...il.com>, kernel@....qualcomm.com,
linux-mmc@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-arm-msm@...r.kernel.org,
netdev@...r.kernel.org, Monish Chunara <quic_mchunara@...cinc.com>
Subject: Re: [PATCH 2/5] arm64: dts: qcom: lemans: Add SDHC controller and SDC
pin configuration
On 9/3/25 6:28 PM, Wasim Nazir wrote:
> On Wed, Sep 03, 2025 at 06:12:59PM +0200, Konrad Dybcio wrote:
>> On 8/27/25 3:20 AM, Dmitry Baryshkov wrote:
>>> On Tue, Aug 26, 2025 at 11:51:01PM +0530, Wasim Nazir wrote:
>>>> From: Monish Chunara <quic_mchunara@...cinc.com>
>>>>
>>>> Introduce the SDHC v5 controller node for the Lemans platform.
>>>> This controller supports either eMMC or SD-card, but only one
>>>> can be active at a time. SD-card is the preferred configuration
>>>> on Lemans targets, so describe this controller.
>>>>
>>>> Define the SDC interface pins including clk, cmd, and data lines
>>>> to enable proper communication with the SDHC controller.
>>>>
>>>> Signed-off-by: Monish Chunara <quic_mchunara@...cinc.com>
>>>> Co-developed-by: Wasim Nazir <wasim.nazir@....qualcomm.com>
>>>> Signed-off-by: Wasim Nazir <wasim.nazir@....qualcomm.com>
>>>> ---
>>>> arch/arm64/boot/dts/qcom/lemans.dtsi | 70 ++++++++++++++++++++++++++++++++++++
>>>> 1 file changed, 70 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/qcom/lemans.dtsi b/arch/arm64/boot/dts/qcom/lemans.dtsi
>>>> index 99a566b42ef2..a5a3cdba47f3 100644
>>>> --- a/arch/arm64/boot/dts/qcom/lemans.dtsi
>>>> +++ b/arch/arm64/boot/dts/qcom/lemans.dtsi
>>>> @@ -3834,6 +3834,36 @@ apss_tpdm2_out: endpoint {
>>>> };
>>>> };
>>>>
>>>> + sdhc: mmc@...4000 {
>>>> + compatible = "qcom,sa8775p-sdhci", "qcom,sdhci-msm-v5";
>>>> + reg = <0x0 0x087c4000 0x0 0x1000>;
>>>> +
>>>> + interrupts = <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
>>>> + <GIC_SPI 521 IRQ_TYPE_LEVEL_HIGH>;
>>>> + interrupt-names = "hc_irq", "pwr_irq";
>>>> +
>>>> + clocks = <&gcc GCC_SDCC1_AHB_CLK>,
>>>> + <&gcc GCC_SDCC1_APPS_CLK>;
>>>> + clock-names = "iface", "core";
>>>> +
>>>> + interconnects = <&aggre1_noc MASTER_SDC 0 &mc_virt SLAVE_EBI1 0>,
>>>> + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDC1 0>;
>>>> + interconnect-names = "sdhc-ddr", "cpu-sdhc";
>>>> +
>>>> + iommus = <&apps_smmu 0x0 0x0>;
>>>> + dma-coherent;
>>>> +
>>>> + resets = <&gcc GCC_SDCC1_BCR>;
>>>> +
>>>> + no-sdio;
>>>> + no-mmc;
>>>> + bus-width = <4>;
>>>
>>> This is the board configuration, it should be defined in the EVK DTS.
>>
>> Unless the controller is actually incapable of doing non-SDCards
>>
>> But from the limited information I can find, this one should be able
>> to do both
>>
>
> It’s doable, but the bus width differs when this controller is used for
> eMMC, which is supported on the Mezz board. So, it’s cleaner to define
> only what’s needed for each specific usecase on the board.
If SD Card is the predominately expected use case, I'm fine with keeping
4 default (in the SoC DTSI) with the odd user overriding that
Konrad
Powered by blists - more mailing lists