| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20251120125449.26530-3-joan.na@analog.com>
Date: Thu, 20 Nov 2025 21:54:49 +0900
From: Joan-Na-adi <joan.na.devcode@...il.com>
To: Liam Girdwood <lgirdwood@...il.com>
Cc: Mark Brown <broonie@...nel.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>,
linux-kernel@...r.kernel.org,
devicetree@...r.kernel.org,
Joan Na <joan.na@...log.com>
Subject: [PATCH v6 2/2] regulator: max77675: Add MAX77675 regulator driver
From: Joan Na <joan.na@...log.com>
Add support for the Maxim Integrated MAX77675 PMIC regulator.
The MAX77675 is a compact, highly efficient SIMO (Single Inductor Multiple Output)
power management IC that provides four programmable buck-boost switching regulators
with only one inductor. It supports up to 700mA total output current and operates
from a single-cell Li-ion battery.
An integrated power-up sequencer and I2C interface allow flexible startup
configuration and runtime control.
Signed-off-by: Joan Na <joan.na@...log.com>
---
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/max77675-regulator.c | 1056 ++++++++++++++++++++++++
3 files changed, 1066 insertions(+)
create mode 100644 drivers/regulator/max77675-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index d84f3d054c59..381edaa90098 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -649,6 +649,15 @@ config REGULATOR_MAX77650
Semiconductor. This device has a SIMO with three independent
power rails and an LDO.
+config REGULATOR_MAX77675
+ tristate "Maxim MAX77675 regulator driver"
+ depends on I2C && OF
+ select REGMAP_I2C
+ help
+ This driver controls the Maxim MAX77675 power regulator via I2C.
+ It supports four programmable buck-boost outputs.
+ Say Y here to enable the regulator driver
+
config REGULATOR_MAX77857
tristate "ADI MAX77857/MAX77831 regulator support"
depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index b3101376029d..cdd99669cd24 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -78,6 +78,7 @@ obj-$(CONFIG_REGULATOR_MAX77503) += max77503-regulator.o
obj-$(CONFIG_REGULATOR_MAX77541) += max77541-regulator.o
obj-$(CONFIG_REGULATOR_MAX77620) += max77620-regulator.o
obj-$(CONFIG_REGULATOR_MAX77650) += max77650-regulator.o
+obj-$(CONFIG_REGULATOR_MAX77675) += max77675-regulator.o
obj-$(CONFIG_REGULATOR_MAX8649) += max8649.o
obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
obj-$(CONFIG_REGULATOR_MAX8893) += max8893.o
diff --git a/drivers/regulator/max77675-regulator.c b/drivers/regulator/max77675-regulator.c
new file mode 100644
index 000000000000..584554680f9d
--- /dev/null
+++ b/drivers/regulator/max77675-regulator.c
@@ -0,0 +1,1056 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2025 Analog Devices, Inc.
+ * ADI regulator driver for MAX77675.
+ */
+
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/cleanup.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+
+/* Register Addresses */
+#define MAX77675_REG_CNFG_GLBL_A 0x00
+#define MAX77675_REG_CNFG_GLBL_B 0x01
+#define MAX77675_REG_INT_GLBL 0x02
+#define MAX77675_REG_INTM_GLBL 0x03
+#define MAX77675_REG_STAT_GLBL 0x04
+#define MAX77675_REG_ERCF_GLBL 0x05
+#define MAX77675_REG_CID 0x06
+#define MAX77675_REG_CNFG_SBB_TOP_A 0x07
+#define MAX77675_REG_CNFG_SBB0_A 0x08
+#define MAX77675_REG_CNFG_SBB0_B 0x09
+#define MAX77675_REG_CNFG_SBB1_A 0x0A
+#define MAX77675_REG_CNFG_SBB1_B 0x0B
+#define MAX77675_REG_CNFG_SBB2_A 0x0C
+#define MAX77675_REG_CNFG_SBB2_B 0x0D
+#define MAX77675_REG_CNFG_SBB3_A 0x0E
+#define MAX77675_REG_CNFG_SBB3_B 0x0F
+#define MAX77675_REG_CNFG_SBB_TOP_B 0x10
+
+/* CNFG_GLBL_A (0x00) bit masks and shifts */
+#define MAX77675_MRT_MASK GENMASK(7, 6) /* Manual Reset Time (bits 7:6) */
+#define MAX77675_MRT_SHIFT 6
+#define MAX77675_PU_DIS_BIT BIT(5) /* Pullup Disable (bit 5) */
+#define MAX77675_PU_DIS_SHIFT 5
+#define MAX77675_BIAS_LPM_BIT BIT(4) /* Bias Low Power Mode (bit 4) */
+#define MAX77675_BIAS_LPM_SHIFT 4
+#define MAX77675_SIMO_CH_DIS_BIT BIT(3) /* SIMO Internal Channel Disable (bit 3) */
+#define MAX77675_SIMO_CH_DIS_SHIFT 3
+#define MAX77675_EN_MODE_MASK GENMASK(2, 1) /* nEN Mode (bits 2:1) */
+#define MAX77675_EN_MODE_SHIFT 1
+#define MAX77675_DBEN_EN_BIT BIT(0) /* Debounce Enable (bit 0) */
+#define MAX77675_DBEN_EN_SHIFT 0
+
+/* CNFG_GLBL_B (0x01) */
+#define MAX77675_SFT_CTRL_MASK GENMASK(2, 0) /* Soft Start Control */
+#define MAX77675_SFT_CTRL_SHIFT 0
+
+/* INT_GLBL (0x02) bit bits and shifts */
+#define MAX77675_INT_SBB3_F_BIT BIT(7)
+#define MAX77675_INT_SBB3_F_SHIFT 7
+#define MAX77675_INT_SBB2_F_BIT BIT(6)
+#define MAX77675_INT_SBB2_F_SHIFT 6
+#define MAX77675_INT_SBB1_F_BIT BIT(5)
+#define MAX77675_INT_SBB1_F_SHIFT 5
+#define MAX77675_INT_SBB0_F_BIT BIT(4)
+#define MAX77675_INT_SBB0_F_SHIFT 4
+#define MAX77675_INT_TJAL2_R_BIT BIT(3)
+#define MAX77675_INT_TJAL2_R_SHIFT 3
+#define MAX77675_INT_TJAL1_R_BIT BIT(2)
+#define MAX77675_INT_TJAL1_R_SHIFT 2
+#define MAX77675_INT_EN_R_BIT BIT(1)
+#define MAX77675_INT_EN_R_SHIFT 1
+#define MAX77675_INT_EN_F_BIT BIT(0)
+#define MAX77675_INT_EN_F_SHIFT 0
+
+/* INTM_GLBL (0x03) bits and shifts */
+#define MAX77675_INTM_SBB3_F_BIT BIT(7)
+#define MAX77675_INTM_SBB3_F_SHIFT 7
+#define MAX77675_INTM_SBB2_F_BIT BIT(6)
+#define MAX77675_INTM_SBB2_F_SHIFT 6
+#define MAX77675_INTM_SBB1_F_BIT BIT(5)
+#define MAX77675_INTM_SBB1_F_SHIFT 5
+#define MAX77675_INTM_SBB0_F_BIT BIT(4)
+#define MAX77675_INTM_SBB0_F_SHIFT 4
+#define MAX77675_INTM_TJAL2_R_BIT BIT(3)
+#define MAX77675_INTM_TJAL2_R_SHIFT 3
+#define MAX77675_INTM_TJAL1_R_BIT BIT(2)
+#define MAX77675_INTM_TJAL1_R_SHIFT 2
+#define MAX77675_INTM_EN_R_BIT BIT(1)
+#define MAX77675_INTM_EN_R_SHIFT 1
+#define MAX77675_INTM_EN_F_BIT BIT(0)
+#define MAX77675_INTM_EN_F_SHIFT 0
+
+/* STAT_GLBL (0x04) bits and shifts */
+#define MAX77675_STAT_SBB3_S_BIT BIT(7)
+#define MAX77675_STAT_SBB3_S_SHIFT 7
+#define MAX77675_STAT_SBB2_S_BIT BIT(6)
+#define MAX77675_STAT_SBB2_S_SHIFT 6
+#define MAX77675_STAT_SBB1_S_BIT BIT(5)
+#define MAX77675_STAT_SBB1_S_SHIFT 5
+#define MAX77675_STAT_SBB0_S_BIT BIT(4)
+#define MAX77675_STAT_SBB0_S_SHIFT 4
+#define MAX77675_STAT_TJAL2_S_BIT BIT(2)
+#define MAX77675_STAT_TJAL2_S_SHIFT 2
+#define MAX77675_STAT_TJAL1_S_BIT BIT(1)
+#define MAX77675_STAT_TJAL1_S_SHIFT 1
+#define MAX77675_STAT_STAT_EN_BIT BIT(0)
+#define MAX77675_STAT_STAT_EN_SHIFT 0
+
+#define MAX77675_STAT_STAT_EN_BIT BIT(0)
+#define MAX77675_STAT_STAT_EN_SHIFT 0
+
+/* ERCFLAG (0x05) bits and shifts */
+#define MAX77675_SFT_CRST_F_BIT BIT(5) /* Software Cold Reset Flag */
+#define MAX77675_SFT_CRST_F_SHIFT 5
+#define MAX77675_SFT_OFF_F_BIT BIT(4) /* Software Off Flag */
+#define MAX77675_SFT_OFF_F_SHIFT 4
+#define MAX77675_MRST_BIT BIT(3) /* Manual Reset Timer Flag */
+#define MAX77675_MRST_SHIFT 3
+#define MAX77675_UVLO_BIT BIT(2) /* Undervoltage Lockout Flag */
+#define MAX77675_UVLO_SHIFT 2
+#define MAX77675_OVLO_BIT BIT(1) /* Overvoltage Lockout Flag */
+#define MAX77675_OVLO_SHIFT 1
+#define MAX77675_TOVLD_BIT BIT(0) /* Thermal Overload Flag */
+#define MAX77675_TOVLD_SHIFT 0
+
+/* CID (0x06) bits and shifts */
+#define MAX77675_CID_MASK GENMASK(4, 0) /* Chip Identification Code mask */
+#define MAX77675_CID_SHIFT 0 /* Starts at bit 0 */
+
+/* CNFG_SBB_TOP_A (0x07) bits and shifts */
+#define MAX77675_STEP_SZ_SBB3_BIT BIT(5)
+#define MAX77675_STEP_SZ_SBB3_SHIFT 5
+#define MAX77675_STEP_SZ_SBB2_BIT BIT(4)
+#define MAX77675_STEP_SZ_SBB2_SHIFT 4
+#define MAX77675_STEP_SZ_SBB1_BIT BIT(3)
+#define MAX77675_STEP_SZ_SBB1_SHIFT 3
+#define MAX77675_STEP_SZ_SBB0_BIT BIT(2)
+#define MAX77675_STEP_SZ_SBB0_SHIFT 2
+#define MAX77675_DRV_SBB_MASK GENMASK(1, 0)
+#define MAX77675_DRV_SBB_SHIFT 0
+
+/* CNFG_SBB0_A (0x08) bits and shifts */
+#define MAX77675_TV_SBB0_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB0_SHIFT 0
+
+/* CNFG_SBB0_B (0x09) bits and shifts */
+#define MAX77675_ADE_SBB0_BIT BIT(3)
+#define MAX77675_ADE_SBB0_SHIFT 3
+#define MAX77675_EN_SBB0_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB0_SHIFT 0
+
+/* CNFG_SBB1_A (0x0A) bits and shifts */
+#define MAX77675_TV_SBB1_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB1_SHIFT 0
+
+/* CNFG_SBB1_B (0x0B) bits and shifts */
+#define MAX77675_ADE_SBB1_BIT BIT(3)
+#define MAX77675_ADE_SBB1_SHIFT 3
+#define MAX77675_EN_SBB1_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB1_SHIFT 0
+
+/* CNFG_SBB2_A (0x0C) bits and shifts */
+#define MAX77675_TV_SBB2_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB2_SHIFT 0
+
+/* CNFG_SBB2_B (0x0D) bits and shifts */
+#define MAX77675_ADE_SBB2_BIT BIT(3)
+#define MAX77675_ADE_SBB2_SHIFT 3
+#define MAX77675_EN_SBB2_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB2_SHIFT 0
+
+/* CNFG_SBB3_A (0x0E) bits and shifts */
+#define MAX77675_TV_SBB3_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB3_SHIFT 0
+
+/* CNFG_SBB3_B (0x0F) bits and shifts */
+#define MAX77675_ADE_SBB3_BIT BIT(3)
+#define MAX77675_ADE_SBB3_SHIFT 3
+#define MAX77675_EN_SBB3_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB3_SHIFT 0
+
+#define MAX77675_EN_SBB_MASK GENMASK(2, 0)
+
+/* CNFG_SBB_TOP_B (0x10) bits and shifts */
+#define MAX77675_DVS_SLEW_BIT BIT(5)
+#define MAX77675_DVS_SLEW_SHIFT 5
+#define MAX77675_LAT_MODE_BIT BIT(4)
+#define MAX77675_LAT_MODE_SHIFT 4
+#define MAX77675_SR_SBB3_BIT BIT(3)
+#define MAX77675_SR_SBB3_SHIFT 3
+#define MAX77675_SR_SBB2_BIT BIT(2)
+#define MAX77675_SR_SBB2_SHIFT 2
+#define MAX77675_SR_SBB1_BIT BIT(1)
+#define MAX77675_SR_SBB1_SHIFT 1
+#define MAX77675_SR_SBB0_BIT BIT(0)
+#define MAX77675_SR_SBB0_SHIFT 0
+
+#define MAX77675_MAX_REGISTER 0x10
+
+/* Common minimum voltage (in microvolts) */
+#define MAX77675_MIN_UV 500000 // 500 mV
+
+/* Voltage step configuration for 25mV mode */
+#define MAX77675_STEP_25MV 25000 // Step size: 25 mV
+#define MAX77675_MAX_UV_25MV 5500000 // Max voltage: 5.5 V
+#define MAX77675_NUM_LEVELS_25MV 201 // levels = (5500mV - 500mV) / 25mV + 1
+
+/* Voltage step configuration for 12.5mV mode */
+#define MAX77675_STEP_12_5MV 12500 // Step size: 12.5 mV
+#define MAX77675_MAX_UV_12_5MV 3687500 // Max voltage: 3.6875 V
+#define MAX77675_NUM_LEVELS_12_5MV 255 // levels = (3687.5mV - 500mV) / 12.5mV + 1
+
+#define MAX77675_ENABLE_OFF 0x04
+#define MAX77675_ENABLE_ON 0x06
+
+#define MAX77675_REGULATOR_AD_OFF 0x00
+#define MAX77675_REGULATOR_AD_ON BIT(3)
+
+/* FPS source */
+#define MAX77675_FPS_SLOT_0 0x0
+#define MAX77675_FPS_SLOT_1 0x1
+#define MAX77675_FPS_SLOT_2 0x2
+#define MAX77675_FPS_SLOT_3 0x3
+#define MAX77675_FPS_DEF 0x4
+
+/* nEN Manual Reset Time Configuration (MRT) */
+#define MAX77675_MRT_4S 0x0
+#define MAX77675_MRT_8S 0x1
+#define MAX77675_MRT_12S 0x2
+#define MAX77675_MRT_16S 0x3
+
+/* nEN Mode Configuration */
+#define MAX77675_EN_PUSH_BUTTON 0x0
+#define MAX77675_EN_SLIDE_SWITCH 0x1
+#define MAX77675_EN_LOGIC 0x2
+
+/* Debounce Timer Enable (DBEN_nEN) */
+#define MAX77675_DBEN_100US 0x0
+#define MAX77675_DBEN_30000US 0x1
+
+/* Rising slew rate control for SBB0 when ramping up */
+#define MAX77675_SR_2MV_PER_US 0x0 // 2 mV/us
+#define MAX77675_SR_USE_DVS 0x1 // Use DVS slew rate setting (adi,dvs-slew-rate)
+
+/* Latency Mode */
+#define MAX77675_HIGH_LATENCY_MODE 0x0 // High latency, low quiescent current (~100us)
+#define MAX77675_LOW_LATENCY_MODE 0x1 // Low latency, high quiescent current (~10us)
+
+/* Dynamic Voltage Scaling (DVS) Slew Rate */
+#define MAX77675_DVS_SLEW_5MV_PER_US 0x0 // 5 mV/us
+#define MAX77675_DVS_SLEW_10MV_PER_US 0x1 // 10 mV/us
+
+/* SIMO Buck-Boost Drive Strength (All Channels) */
+#define MAX77675_DRV_SBB_STRENGTH_MAX 0x0 // Maximum drive strength (~0.6 ns transition time)
+#define MAX77675_DRV_SBB_STRENGTH_HIGH 0x1 // High drive strength (~1.2 ns transition time)
+#define MAX77675_DRV_SBB_STRENGTH_LOW 0x2 // Low drive strength (~1.8 ns transition time)
+#define MAX77675_DRV_SBB_STRENGTH_MIN 0x3 // Minimum drive strength (~8 ns transition time)
+
+/* Regulator ID enumeration */
+enum max77675_regulator_id {
+ MAX77675_ID_SBB0 = 0,
+ MAX77675_ID_SBB1,
+ MAX77675_ID_SBB2,
+ MAX77675_ID_SBB3,
+ MAX77675_ID_NUM_MAX,
+};
+
+struct max77675_regulator_sbb_setting {
+ u8 fps_slot;
+ bool fixed_slew_rate;
+};
+
+struct max77675_config {
+ u8 en_mode;
+ u8 voltage_change_latency;
+ u8 drv_sbb_strength;
+ u8 dvs_slew_rate;
+ u8 debounce_time;
+ u8 manual_reset_time;
+ bool en_pullup_disable;
+ bool bias_low_power_request;
+ bool simo_ldo_always_on;
+};
+
+struct max77675_regulator {
+ struct device *dev;
+ struct regmap *regmap;
+ struct max77675_config config;
+ struct max77675_regulator_sbb_setting sbb_setting[MAX77675_ID_NUM_MAX];
+};
+
+static int max77675_regulator_get_fps_src(struct max77675_regulator *maxreg, int id)
+{
+ unsigned int reg_addr;
+ unsigned int val;
+ int ret;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ reg_addr = MAX77675_REG_CNFG_SBB0_B;
+ break;
+ case MAX77675_ID_SBB1:
+ reg_addr = MAX77675_REG_CNFG_SBB1_B;
+ break;
+ case MAX77675_ID_SBB2:
+ reg_addr = MAX77675_REG_CNFG_SBB2_B;
+ break;
+ case MAX77675_ID_SBB3:
+ reg_addr = MAX77675_REG_CNFG_SBB3_B;
+ break;
+ default:
+ dev_err(maxreg->dev, "Invalid regulator id: %d\n", id);
+ return -EINVAL;
+ }
+
+ ret = regmap_read(maxreg->regmap, reg_addr, &val);
+ if (ret < 0) {
+ dev_err(maxreg->dev, "Failed to read FPS source (reg 0x%02x): %d\n",
+ reg_addr, ret);
+ return ret;
+ }
+
+ return FIELD_GET(MAX77675_EN_SBB_MASK, val);
+}
+
+static int max77675_regulator_set_fps_src(struct max77675_regulator *maxreg, int id, u8 fps_src)
+{
+ unsigned int reg_addr;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ reg_addr = MAX77675_REG_CNFG_SBB0_B;
+ break;
+ case MAX77675_ID_SBB1:
+ reg_addr = MAX77675_REG_CNFG_SBB1_B;
+ break;
+ case MAX77675_ID_SBB2:
+ reg_addr = MAX77675_REG_CNFG_SBB2_B;
+ break;
+ case MAX77675_ID_SBB3:
+ reg_addr = MAX77675_REG_CNFG_SBB3_B;
+ break;
+ default:
+ dev_err(maxreg->dev, "Invalid regulator id: %d\n", id);
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(maxreg->regmap, reg_addr, MAX77675_EN_SBB_MASK, fps_src);
+}
+
+static int max77675_set_sbb_slew_rate_fixed(struct max77675_regulator *maxreg, int id, bool fixed)
+{
+ u8 mask, value;
+ u8 slew_src_ctrl_bit = fixed ? 0 : 1;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ mask = MAX77675_SR_SBB0_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB0_BIT, slew_src_ctrl_bit);
+ break;
+
+ case MAX77675_ID_SBB1:
+ mask = MAX77675_SR_SBB1_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB1_BIT, slew_src_ctrl_bit);
+ break;
+
+ case MAX77675_ID_SBB2:
+ mask = MAX77675_SR_SBB2_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB2_BIT, slew_src_ctrl_bit);
+ break;
+
+ case MAX77675_ID_SBB3:
+ mask = MAX77675_SR_SBB3_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB3_BIT, slew_src_ctrl_bit);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_B, mask, value);
+}
+
+static int max77675_init_regulator(struct max77675_regulator *maxreg, int id)
+{
+ struct max77675_regulator_sbb_setting *sbb_setting = &maxreg->sbb_setting[id];
+ int ret;
+
+ if (sbb_setting->fps_slot == MAX77675_FPS_DEF) {
+ ret = max77675_regulator_get_fps_src(maxreg, id);
+ if (ret < 0)
+ return ret;
+
+ sbb_setting->fps_slot = ret;
+ } else {
+ ret = max77675_regulator_set_fps_src(maxreg, id, sbb_setting->fps_slot);
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = max77675_set_sbb_slew_rate_fixed(maxreg, id, sbb_setting->fixed_slew_rate);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static int max77675_of_parse_cb(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
+{
+ struct max77675_regulator *maxreg = config->driver_data;
+ struct max77675_regulator_sbb_setting *sbb_setting = &maxreg->sbb_setting[desc->id];
+ static const char * const fps_slots[] = { "slot0", "slot1", "slot2", "slot3", "default" };
+ const char *fps_str;
+ int slot;
+
+ /* Parse FPS slot from DT */
+ if (of_property_read_string(np, "adi,fps-slot", &fps_str)) {
+ /* Property not set, use default */
+ sbb_setting->fps_slot = MAX77675_FPS_DEF;
+ } else {
+ /* Match string to index */
+ slot = match_string(fps_slots, ARRAY_SIZE(fps_slots), fps_str);
+ if (slot < 0) {
+ dev_dbg(maxreg->dev, "Invalid fps-slot '%s', using default\n", fps_str);
+ sbb_setting->fps_slot = MAX77675_FPS_DEF;
+ } else {
+ sbb_setting->fps_slot = slot;
+ }
+ }
+
+ /* Parse slew rate control source */
+ sbb_setting->fixed_slew_rate = of_property_read_bool(np, "adi,fixed-slew-rate");
+
+ /* Apply parsed configuration */
+ return max77675_init_regulator(maxreg, desc->id);
+}
+
+static int max77675_get_error_flags(struct regulator_dev *rdev, unsigned int *flags)
+{
+ struct max77675_regulator *maxreg = rdev_get_drvdata(rdev);
+ unsigned int int_flags;
+ int id = rdev_get_id(rdev);
+ int ret;
+
+ ret = regmap_read(maxreg->regmap, MAX77675_REG_INT_GLBL, &int_flags);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to read INT_GLBL: %d\n", ret);
+ return ret;
+ }
+
+ *flags = 0;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ if (int_flags & MAX77675_INT_SBB0_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ case MAX77675_ID_SBB1:
+ if (int_flags & MAX77675_INT_SBB1_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ case MAX77675_ID_SBB2:
+ if (int_flags & MAX77675_INT_SBB2_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ case MAX77675_ID_SBB3:
+ if (int_flags & MAX77675_INT_SBB3_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ default:
+ dev_warn(maxreg->dev, "Unsupported regulator ID: %d\n", id);
+ break;
+ }
+
+ if (int_flags & MAX77675_INT_TJAL2_R_BIT) {
+ /* TJAL2 interrupt: Over-temperature condition (above 120 degree) */
+ *flags |= REGULATOR_ERROR_OVER_TEMP;
+ }
+
+ return 0;
+}
+
+static const struct regulator_ops max77675_regulator_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .map_voltage = regulator_map_voltage_linear,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+ .get_error_flags = max77675_get_error_flags,
+};
+
+static struct regulator_desc max77675_regulators[MAX77675_ID_NUM_MAX] = {
+ {
+ .name = "sbb0",
+ .of_match = of_match_ptr("sbb0"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB0,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB0_A,
+ .vsel_mask = MAX77675_TV_SBB0_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB0_B,
+ .enable_mask = MAX77675_EN_SBB0_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_ADE_SBB0_BIT,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB0_B,
+ },
+ {
+ .name = "sbb1",
+ .of_match = of_match_ptr("sbb1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB1,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB1_A,
+ .vsel_mask = MAX77675_TV_SBB1_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB1_B,
+ .enable_mask = MAX77675_EN_SBB1_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_ADE_SBB1_BIT,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB1_B,
+ },
+ {
+ .name = "sbb2",
+ .of_match = of_match_ptr("sbb2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB2,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB2_A,
+ .vsel_mask = MAX77675_TV_SBB2_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB2_B,
+ .enable_mask = MAX77675_EN_SBB2_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_ADE_SBB2_BIT,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB2_B,
+ },
+ {
+ .name = "sbb3",
+ .of_match = of_match_ptr("sbb3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB3,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB3_A,
+ .vsel_mask = MAX77675_TV_SBB3_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB3_B,
+ .enable_mask = MAX77675_EN_SBB3_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_ADE_SBB3_BIT,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB3_B,
+ },
+};
+
+static bool max77675_volatile_reg(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case MAX77675_REG_CNFG_GLBL_B:
+ /* This register can be updated by an internal state machine */
+ case MAX77675_REG_INT_GLBL:
+ case MAX77675_REG_STAT_GLBL:
+ case MAX77675_REG_ERCF_GLBL:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static const struct regmap_config max77675_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MAX77675_MAX_REGISTER,
+ .cache_type = REGCACHE_MAPLE,
+ .volatile_reg = max77675_volatile_reg,
+};
+
+static int max77675_apply_config(struct max77675_regulator *maxreg)
+{
+ const struct max77675_config *cfg = &maxreg->config;
+ int ret;
+
+ /* Set EN pin mode */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_EN_MODE_MASK,
+ FIELD_PREP(MAX77675_EN_MODE_MASK, cfg->en_mode));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set EN mode: %d\n", ret);
+ return ret;
+ }
+
+ /* Set the latency between output voltage change and SBBx voltage ramp start */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_B,
+ MAX77675_LAT_MODE_BIT,
+ FIELD_PREP(MAX77675_LAT_MODE_BIT, cfg->voltage_change_latency));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set latency mode: %d\n", ret);
+ return ret;
+ }
+
+ /* Set drive strength */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_A,
+ MAX77675_DRV_SBB_MASK,
+ FIELD_PREP(MAX77675_DRV_SBB_MASK, cfg->drv_sbb_strength));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set drive strength: %d\n", ret);
+ return ret;
+ }
+
+ /* Set DVS slew rate */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_B,
+ MAX77675_DVS_SLEW_BIT,
+ FIELD_PREP(MAX77675_DVS_SLEW_BIT, cfg->dvs_slew_rate));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set DVS slew rate: %d\n", ret);
+ return ret;
+ }
+
+ /* Set debounce time for EN pin */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_DBEN_EN_BIT,
+ FIELD_PREP(MAX77675_DBEN_EN_BIT, cfg->debounce_time));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set EN debounce time: %d\n", ret);
+ return ret;
+ }
+
+ /* Set manual reset time (MRT) for EN pin */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_MRT_MASK,
+ FIELD_PREP(MAX77675_MRT_MASK, cfg->manual_reset_time));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set manual reset time: %d\n", ret);
+ return ret;
+ }
+
+ /* Enable or disable internal pull-up resistor on EN pin */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_PU_DIS_BIT,
+ FIELD_PREP(MAX77675_PU_DIS_BIT, cfg->en_pullup_disable));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set EN pull-up disable: %d\n", ret);
+ return ret;
+ }
+
+ /* Request main bias to enter low-power mode */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_BIAS_LPM_BIT,
+ FIELD_PREP(MAX77675_BIAS_LPM_BIT, cfg->bias_low_power_request));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set bias low-power request: %d\n", ret);
+ return ret;
+ }
+
+ /* Force SIMO internal LDO to always supply 1.8V */
+ ret = regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_SIMO_CH_DIS_BIT,
+ FIELD_PREP(MAX77675_SIMO_CH_DIS_BIT, cfg->simo_ldo_always_on));
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set SIMO internal LDO always-on: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int max77675_parse_en_mode(struct device *dev,
+ struct device_node *np,
+ u8 *en_mode)
+{
+ static const char * const en_modes[] = {"push-button", "slide-switch", "logic"};
+ const char *str;
+ int index;
+
+ *en_mode = MAX77675_EN_SLIDE_SWITCH;
+
+ if (of_property_read_string(np, "adi,en-mode", &str))
+ return 0;
+
+ index = match_string(en_modes, ARRAY_SIZE(en_modes), str);
+ if (index < 0) {
+ dev_err(dev, "Invalid 'adi,en-mode' value '%s'\n", str);
+ return -EINVAL;
+ }
+
+ *en_mode = index;
+
+ return 0;
+}
+
+static int max77675_parse_voltage_change_latency(struct device *dev,
+ struct device_node *np,
+ u8 *latency_mode)
+{
+ u32 val;
+
+ *latency_mode = MAX77675_HIGH_LATENCY_MODE;
+
+ if (!of_property_read_u32(np, "adi,voltage-change-latency-us", &val)) {
+ switch (val) {
+ case 10:
+ *latency_mode = MAX77675_LOW_LATENCY_MODE;
+ break;
+ case 100:
+ *latency_mode = MAX77675_HIGH_LATENCY_MODE;
+ break;
+ default:
+ dev_err(dev, "Invalid voltage-change-latency-us value: %u\n", val);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static int max77675_parse_manual_reset_time(struct device *dev,
+ struct device_node *np,
+ u8 *reset_time)
+{
+ u32 val;
+
+ *reset_time = MAX77675_MRT_4S;
+
+ if (!of_property_read_u32(np, "reset-time-sec", &val)) {
+ switch (val) {
+ case 4:
+ *reset_time = MAX77675_MRT_4S;
+ break;
+ case 8:
+ *reset_time = MAX77675_MRT_8S;
+ break;
+ case 12:
+ *reset_time = MAX77675_MRT_12S;
+ break;
+ case 16:
+ *reset_time = MAX77675_MRT_16S;
+ break;
+ default:
+ dev_err(dev, "Invalid reset-time-sec value: %u\n", val);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static int max77675_parse_dvs_slew_rate(struct device *dev, struct device_node *np, u8 *slew_rate)
+{
+ u32 val;
+
+ /* Set default: 5 mV/us */
+ *slew_rate = MAX77675_DVS_SLEW_5MV_PER_US;
+
+ if (!of_property_read_u32(np, "adi,dvs-slew-rate-mv-per-us", &val)) {
+ switch (val) {
+ case 5:
+ *slew_rate = MAX77675_DVS_SLEW_5MV_PER_US;
+ break;
+ case 10:
+ *slew_rate = MAX77675_DVS_SLEW_10MV_PER_US;
+ break;
+ default:
+ dev_err(dev, "Invalid dvs-slew-rate-mv-per-us value: %u\n", val);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static int max77675_parse_drv_sbb_strength(struct device *dev, struct device_node *np, u8 *strength)
+{
+ static const char * const strength_names[] = {"max", "high", "low", "min"};
+ const char *str;
+ int index;
+
+ /* Set default: maximum drive strength */
+ *strength = MAX77675_DRV_SBB_STRENGTH_MAX;
+
+ if (of_property_read_string(np, "adi,drv-sbb-strength", &str))
+ return 0;
+
+ index = match_string(strength_names, ARRAY_SIZE(strength_names), str);
+ if (index < 0) {
+ dev_err(dev, "Invalid 'adi,drv-sbb-strength' value: '%s'\n", str);
+ return -EINVAL;
+ }
+
+ *strength = index;
+
+ return 0;
+}
+
+static int max77675_parse_debounce_time_us(struct device *dev,
+ struct device_node *np,
+ u8 *debounce_time)
+{
+ u32 val;
+
+ *debounce_time = MAX77675_DBEN_100US;
+
+ if (!of_property_read_u32(np, "input-debounce", &val)) {
+ switch (val) {
+ case 100:
+ *debounce_time = MAX77675_DBEN_100US;
+ break;
+ case 30000:
+ *debounce_time = MAX77675_DBEN_30000US;
+ break;
+ default:
+ dev_err(dev, "Invalid input-debounce value: %u\n", val);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static int max77675_parse_config(struct max77675_regulator *maxreg)
+{
+ struct device_node *np = maxreg->dev->of_node;
+ struct max77675_config *cfg = &maxreg->config;
+ int ret;
+
+ /* EN pin mode */
+ ret = max77675_parse_en_mode(maxreg->dev, np, &cfg->en_mode);
+ if (ret < 0)
+ return ret;
+
+ /* voltage change latency */
+ ret = max77675_parse_voltage_change_latency(maxreg->dev, np, &cfg->voltage_change_latency);
+ if (ret < 0)
+ return ret;
+
+ /* drive strength */
+ ret = max77675_parse_drv_sbb_strength(maxreg->dev, np, &cfg->drv_sbb_strength);
+ if (ret < 0)
+ return ret;
+
+ /* dvs slew rate */
+ ret = max77675_parse_dvs_slew_rate(maxreg->dev, np, &cfg->dvs_slew_rate);
+ if (ret < 0)
+ return ret;
+
+ /* Debounce time for EN pin */
+ ret = max77675_parse_debounce_time_us(maxreg->dev, np, &cfg->debounce_time);
+ if (ret < 0)
+ return ret;
+
+ /* Manual reset time for EN pin */
+ ret = max77675_parse_manual_reset_time(maxreg->dev, np, &cfg->manual_reset_time);
+ if (ret < 0)
+ return ret;
+
+ /* Disable internal pull-up resistor on EN pin */
+ cfg->en_pullup_disable = of_property_read_bool(np, "bias-disable");
+
+ /* Request low-power mode for main bias */
+ cfg->bias_low_power_request = of_property_read_bool(np, "adi,bias-low-power-request");
+
+ /* Force internal LDO to always supply 1.8V */
+ cfg->simo_ldo_always_on = of_property_read_bool(np, "adi,simo-ldo-always-on");
+
+ return ret;
+}
+
+static int max77675_init_event(struct max77675_regulator *maxreg)
+{
+ unsigned int ercflag, int_glbl;
+ int ret;
+
+ ret = regmap_read(maxreg->regmap, MAX77675_REG_ERCF_GLBL, &ercflag);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to read CID register: %d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_read(maxreg->regmap, MAX77675_REG_INT_GLBL, &int_glbl);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to read INT_GLBL register: %d\n", ret);
+ return ret;
+ }
+
+ if (ercflag & MAX77675_SFT_CRST_F_BIT)
+ dev_dbg(maxreg->dev, "Software Cold Reset Flag is set\n");
+
+ if (ercflag & MAX77675_SFT_OFF_F_BIT)
+ dev_dbg(maxreg->dev, "Software Off Flag is set\n");
+
+ if (ercflag & MAX77675_MRST_BIT)
+ dev_dbg(maxreg->dev, "Manual Reset Timer Flag is set\n");
+
+ if (ercflag & MAX77675_UVLO_BIT)
+ dev_dbg(maxreg->dev, "Undervoltage Lockout Flag is set\n");
+
+ if (ercflag & MAX77675_OVLO_BIT)
+ dev_dbg(maxreg->dev, "Overvoltage Lockout Flag is set\n");
+
+ if (ercflag & MAX77675_TOVLD_BIT)
+ dev_dbg(maxreg->dev, "Thermal Overload Flag is set\n");
+
+ if (int_glbl & MAX77675_INT_SBB3_F_BIT)
+ dev_dbg(maxreg->dev, "SBB3 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_SBB2_F_BIT)
+ dev_dbg(maxreg->dev, "SBB2 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_SBB1_F_BIT)
+ dev_dbg(maxreg->dev, "SBB1 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_SBB0_F_BIT)
+ dev_dbg(maxreg->dev, "SBB0 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_TJAL2_R_BIT)
+ dev_dbg(maxreg->dev, "Thermal Alarm 2 Rising Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_TJAL1_R_BIT)
+ dev_dbg(maxreg->dev, "Thermal Alarm 1 Rising Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_EN_R_BIT)
+ dev_dbg(maxreg->dev, "nEN Rising Edge Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_EN_F_BIT)
+ dev_dbg(maxreg->dev, "nEN Falling Edge Interrupt occurred\n");
+
+ return 0;
+}
+
+static int max77675_regulator_probe(struct i2c_client *client)
+{
+ struct max77675_regulator *maxreg;
+ struct regulator_config config = {};
+ struct device_node *regulators_np __free(device_node) = NULL;
+ int i, ret;
+
+ maxreg = devm_kzalloc(&client->dev, sizeof(*maxreg), GFP_KERNEL);
+ if (!maxreg)
+ return -ENOMEM;
+
+ maxreg->dev = &client->dev;
+
+ maxreg->regmap = devm_regmap_init_i2c(client, &max77675_regmap_config);
+ if (IS_ERR(maxreg->regmap))
+ return dev_err_probe(maxreg->dev,
+ PTR_ERR(maxreg->regmap),
+ "Failed to init regmap\n");
+
+ ret = max77675_init_event(maxreg);
+ if (ret < 0)
+ return dev_err_probe(maxreg->dev, ret, "Failed to init event\n");
+
+ ret = max77675_parse_config(maxreg);
+ if (ret < 0)
+ return dev_err_probe(maxreg->dev, ret, "Failed to parse config\n");
+
+ ret = max77675_apply_config(maxreg);
+ if (ret < 0)
+ return dev_err_probe(maxreg->dev, ret, "Failed to apply config\n");
+
+ config.dev = &client->dev;
+ config.regmap = maxreg->regmap;
+ config.driver_data = maxreg;
+
+ regulators_np = of_get_child_by_name(client->dev.of_node, "regulators");
+ if (!regulators_np) {
+ dev_err(maxreg->dev, "No 'regulators' subnode found in DT\n");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < MAX77675_ID_NUM_MAX; i++) {
+ const struct regulator_desc *desc = &max77675_regulators[i];
+ struct regulator_dev *rdev;
+
+ struct device_node *child_np __free(device_node) =
+ of_get_child_by_name(regulators_np, desc->name);
+ if (!child_np) {
+ dev_warn(maxreg->dev, "No DT node for regulator %s\n", desc->name);
+ continue;
+ }
+
+ config.of_node = child_np;
+
+ rdev = devm_regulator_register(&client->dev, desc, &config);
+ if (IS_ERR(rdev)) {
+ return dev_err_probe(maxreg->dev, PTR_ERR(rdev),
+ "Failed to register regulator %d (%s)\n",
+ i, desc->name);
+ }
+ }
+
+ return 0;
+}
+
+static const struct i2c_device_id max77675_i2c_id[] = {
+ { "max77675", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, max77675_i2c_id);
+
+static const struct of_device_id __maybe_unused max77675_of_match[] = {
+ { .compatible = "adi,max77675", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, max77675_of_match);
+
+static struct i2c_driver max77675_regulator_driver = {
+ .driver = {
+ .name = "max77675",
+ .of_match_table = of_match_ptr(max77675_of_match),
+ },
+ .probe = max77675_regulator_probe,
+ .id_table = max77675_i2c_id,
+};
+
+module_i2c_driver(max77675_regulator_driver);
+
+MODULE_DESCRIPTION("MAX77675 Regulator Driver");
+MODULE_AUTHOR("Joan Na <joan.na@...log.com>");
+MODULE_LICENSE("GPL");
--
2.34.1
Powered by blists - more mailing lists