| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20251219-upstream_v3_glymur_introduction-v3-4-32271f1f685d@oss.qualcomm.com>
Date: Fri, 19 Dec 2025 20:16:57 +0530
From: Pankaj Patil <pankaj.patil@....qualcomm.com>
To: Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konradybcio@...nel.org>, Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzk+dt@...nel.org>,
Conor Dooley <conor+dt@...nel.org>
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
Pankaj Patil <pankaj.patil@....qualcomm.com>,
rajendra.nayak@....qualcomm.com, sibi.sankar@....qualcomm.com,
Kamal Wadhwa <kamal.wadhwa@....qualcomm.com>,
Qiang Yu <qiang.yu@....qualcomm.com>,
Jyothi Kumar Seerapu <jyothi.seerapu@....qualcomm.com>
Subject: [PATCH v3 4/4] arm64: dts: qcom: glymur: Enable Glymur CRD board
support
Add initial device tree support for the Glymur Compute Reference
Device(CRD) board, with this board dts glymur crd can boot to shell
with rootfs on nvme and uart21 as serial console
Features enabled are:
- Regulators 0 - 4
- Power supplies and sideband signals (PERST, WAKE, CLKREQ) for
PCIe3b/4/5/6 controllers and PHYs
- QUPv3 instances
- PMIC thermal-zone updates
Co-developed-by: Kamal Wadhwa <kamal.wadhwa@....qualcomm.com>
Signed-off-by: Kamal Wadhwa <kamal.wadhwa@....qualcomm.com>
Co-developed-by: Qiang Yu <qiang.yu@....qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@....qualcomm.com>
Co-developed-by: Sibi Sankar <sibi.sankar@....qualcomm.com>
Signed-off-by: Sibi Sankar <sibi.sankar@....qualcomm.com>
Co-developed-by: Jyothi Kumar Seerapu <jyothi.seerapu@....qualcomm.com>
Signed-off-by: Jyothi Kumar Seerapu <jyothi.seerapu@....qualcomm.com>
Signed-off-by: Pankaj Patil <pankaj.patil@....qualcomm.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/glymur-crd.dts | 860 ++++++++++++++++++++++++++++++++
2 files changed, 861 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 6f34d5ed331c..6ff911cca06c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM) += glymur-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += hamoa-iot-evk.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq5018-rdp432-c2.dtb
dtb-$(CONFIG_ARCH_QCOM) += ipq5018-tplink-archer-ax55-v1.dtb
diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dts b/arch/arm64/boot/dts/qcom/glymur-crd.dts
new file mode 100644
index 000000000000..7c168e813f1e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dts
@@ -0,0 +1,860 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include "glymur.dtsi"
+#include "glymur-pmics.dtsi"
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+/ {
+ model = "Qualcomm Technologies, Inc. Glymur CRD";
+ compatible = "qcom,glymur-crd", "qcom,glymur";
+
+ aliases {
+ serial0 = &uart21;
+ serial1 = &uart14;
+ i2c0 = &i2c0;
+ i2c1 = &i2c4;
+ i2c2 = &i2c5;
+ spi0 = &spi18;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ clock-frequency = <38400000>;
+ #clock-cells = <0>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&key_vol_up_default>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pmh0101_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ vreg_nvme: regulator-nvme {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_NVME_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmh0101_gpios 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&nvme_reg_en>;
+ pinctrl-names = "default";
+ };
+
+ vreg_nvme_sec: regulator-nvme-sec {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_NVME_SEC_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmh0110_f_e1_gpios 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&nvme_sec_reg_en>;
+ pinctrl-names = "default";
+ };
+
+ vreg_wlan: regulator-wlan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WLAN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 94 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_reg_en>;
+ };
+
+ vreg_wwan: regulator-wwan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WWAN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 246 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wwan_reg_en>;
+ };
+
+ vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ thermal-zones {
+ pmh0101-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmh0101_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmcx0102-c0-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmcx0102_c_e0_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmcx0102-d0-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmcx0102_d_e0_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmcx0102-c1-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmcx0102_c_e1_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmcx0102-d1-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmcx0102_d_e1_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmh0110-f0-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmh0110_f_e0_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmh0110-h0-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmh0110_h_e0_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmh0110-f1-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmh0110_f_e1_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmh0104-i0-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmh0104_i_e0_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmh0104-j0-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmh0104_j_e0_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmh0104-l1-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmh0104_l_e1_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <4 4>, /* EC TZ Secure I3C */
+ <10 2>, /* OOB UART */
+ <44 4>; /* Security SPI (TPM) */
+
+ pcie4_default: pcie4-default-state {
+ clkreq-n-pins {
+ pins = "gpio147";
+ function = "pcie4_clk_req_n";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio146";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio148";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie5_default: pcie5-default-state {
+ clkreq-n-pins {
+ pins = "gpio153";
+ function = "pcie5_clk_req_n";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio152";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio154";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie6_default: pcie6-default-state {
+ clkreq-n-pins {
+ pins = "gpio150";
+ function = "pcie6_clk_req_n";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio149";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio151";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie3b_default: pcie3b-default-state {
+ clkreq-n-pins {
+ pins = "gpio156";
+ function = "pcie3b_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio155";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio157";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ wlan_reg_en: wlan-reg-en-state {
+ pins = "gpio94";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wwan_reg_en: wwan-reg-en-state {
+ pins = "gpio246";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&pmh0101_gpios {
+ key_vol_up_default: key-vol-up-default-state {
+ pins = "gpio6";
+ function = "normal";
+ output-disable;
+ bias-pull-up;
+ };
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pmh0101-rpmh-regulators";
+ qcom,pmic-id = "B_E0";
+
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ vdd-l1-l10-l15-supply = <&vreg_s9f_e0_1p9>;
+ vdd-l2-l7-l8-l9-l16-supply = <&vreg_bob1_e0>;
+ vdd-l11-l12-l18-supply = <&vreg_s7f_e0_1p32>;
+ vdd-l17-supply = <&vreg_bob2_e0>;
+
+ vreg_bob1_e0: bob1 {
+ regulator-name = "vreg_bob1_e0";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <4224000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+
+ vreg_bob2_e0: bob2 {
+ regulator-name = "vreg_bob2_e0";
+ regulator-min-microvolt = <2540000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+
+ vreg_l1b_e0_1p8: ldo1 {
+ regulator-name = "vreg_l1b_e0_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_e0_2p9: ldo2 {
+ regulator-name = "vreg_l2b_e0_2p9";
+ regulator-min-microvolt = <2904000>;
+ regulator-max-microvolt = <2904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_e0_2p79: ldo7 {
+ regulator-name = "vreg_l7b_e0_2p79";
+ regulator-min-microvolt = <2790000>;
+ regulator-max-microvolt = <2792000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_e0_1p50: ldo8 {
+ regulator-name = "vreg_l8b_e0_1p50";
+ regulator-min-microvolt = <1504000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_e0_2p7: ldo9 {
+ regulator-name = "vreg_l9b_e0_2p7";
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10b_e0_1p8: ldo10 {
+ regulator-name = "vreg_l10b_e0_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_e0_1p2: ldo11 {
+ regulator-name = "vreg_l11b_e0_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_e0_1p14: ldo12 {
+ regulator-name = "vreg_l12b_e0_1p14";
+ regulator-min-microvolt = <1144000>;
+ regulator-max-microvolt = <1144000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_e0_1p8: ldo15 {
+ regulator-name = "vreg_l15b_e0_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_e0_2p4: ldo17 {
+ regulator-name = "vreg_l17b_e0_2p4";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <2700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l18b_e0_1p2: ldo18 {
+ regulator-name = "vreg_l18b_e0_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pmcx0102-rpmh-regulators";
+ qcom,pmic-id = "C_E1";
+
+ vdd-l2-supply = <&vreg_s7f_e0_1p32>;
+ vdd-l1-l3-l4-supply = <&vreg_s8f_e0_0p95>;
+
+ vreg_l1c_e1_0p82: ldo1 {
+ regulator-name = "vreg_l1c_e1_0p82";
+ regulator-min-microvolt = <832000>;
+ regulator-max-microvolt = <832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c_e1_1p14: ldo2 {
+ regulator-name = "vreg_l2c_e1_1p14";
+ regulator-min-microvolt = <1144000>;
+ regulator-max-microvolt = <1144000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c_e1_0p89: ldo3 {
+ regulator-name = "vreg_l3c_e1_0p89";
+ regulator-min-microvolt = <890000>;
+ regulator-max-microvolt = <980000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c_e1_0p72: ldo4 {
+ regulator-name = "vreg_l4c_e1_0p72";
+ regulator-min-microvolt = <720000>;
+ regulator-max-microvolt = <720000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pmh0110-rpmh-regulators";
+ qcom,pmic-id = "F_E0";
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-l2-supply = <&vreg_s8f_e0_0p95>;
+ vdd-l3-supply = <&vreg_s8f_e0_0p95>;
+ vdd-l4-supply = <&vreg_s8f_e0_0p95>;
+
+ vreg_s7f_e0_1p32: smps7 {
+ regulator-name = "vreg_s7f_e0_1p32";
+ regulator-min-microvolt = <1320000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s8f_e0_0p95: smps8 {
+ regulator-name = "vreg_s8f_e0_0p95";
+ regulator-min-microvolt = <952000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s9f_e0_1p9: smps9 {
+ regulator-name = "vreg_s9f_e0_1p9";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_e0_0p82: ldo2 {
+ regulator-name = "vreg_l2f_e0_0p82";
+ regulator-min-microvolt = <832000>;
+ regulator-max-microvolt = <832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_e0_0p72: ldo3 {
+ regulator-name = "vreg_l3f_e0_0p72";
+ regulator-min-microvolt = <720000>;
+ regulator-max-microvolt = <720000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4f_e0_0p3: ldo4 {
+ regulator-name = "vreg_l4f_e0_0p3";
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pmh0110-rpmh-regulators";
+ qcom,pmic-id = "F_E1";
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-l1-supply = <&vreg_s8f_e0_0p95>;
+ vdd-l2-supply = <&vreg_s8f_e0_0p95>;
+ vdd-l4-supply = <&vreg_s8f_e0_0p95>;
+
+ vreg_s7f_e1_0p3: smps7 {
+ regulator-name = "vreg_s7f_e1_0p3";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_e1_0p82: ldo1 {
+ regulator-name = "vreg_l1f_e1_0p82";
+ regulator-min-microvolt = <832000>;
+ regulator-max-microvolt = <832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_e1_0p83: ldo2 {
+ regulator-name = "vreg_l2f_e1_0p83";
+ regulator-min-microvolt = <832000>;
+ regulator-max-microvolt = <832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4f_e1_1p08: ldo4 {
+ regulator-name = "vreg_l4f_e1_1p08";
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pmh0110-rpmh-regulators";
+ qcom,pmic-id = "H_E0";
+
+ vdd-l1-supply = <&vreg_s8f_e0_0p95>;
+ vdd-l2-supply = <&vreg_s8f_e0_0p95>;
+ vdd-l3-supply = <&vreg_s9f_e0_1p9>;
+ vdd-l4-supply = <&vreg_s7f_e0_1p32>;
+
+ vreg_l1h_e0_0p89: ldo1 {
+ regulator-name = "vreg_l1h_e0_0p89";
+ regulator-min-microvolt = <832000>;
+ regulator-max-microvolt = <832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2h_e0_0p72: ldo2 {
+ regulator-name = "vreg_l2h_e0_0p72";
+ regulator-min-microvolt = <832000>;
+ regulator-max-microvolt = <832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3h_e0_0p32: ldo3 {
+ regulator-name = "vreg_l3h_e0_0p32";
+ regulator-min-microvolt = <320000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4h_e0_1p2: ldo4 {
+ regulator-name = "vreg_l4h_e0_1p2";
+ regulator-min-microvolt = <1080000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpi_dma2 {
+ status = "okay";
+};
+
+&pmk8850_rtc {
+ qcom,no-alarm;
+};
+
+&pmh0101_gpios {
+ nvme_reg_en: nvme-reg-en-state {
+ pins = "gpio14";
+ function = "normal";
+ bias-disable;
+ };
+};
+
+&qupv3_0 {
+ status = "okay";
+};
+
+&qupv3_1 {
+ status = "okay";
+};
+
+&qupv3_2 {
+ status = "okay";
+};
+
+&pmh0110_f_e1_gpios {
+ nvme_sec_reg_en: nvme-reg-en-state {
+ pins = "gpio14";
+ function = "normal";
+ bias-disable;
+ };
+};
+
+&pcie3b {
+ vddpe-3v3-supply = <&vreg_nvme_sec>;
+
+ pinctrl-0 = <&pcie3b_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie3b_phy {
+ vdda-phy-supply = <&vreg_l3c_e1_0p89>;
+ vdda-pll-supply = <&vreg_l2c_e1_1p14>;
+
+ status = "okay";
+};
+
+&pcie3b_port0 {
+ reset-gpios = <&tlmm 155 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 157 GPIO_ACTIVE_LOW>;
+};
+
+&pcie4 {
+ vddpe-3v3-supply = <&vreg_wlan>;
+
+ pinctrl-0 = <&pcie4_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie4_phy {
+ vdda-phy-supply = <&vreg_l1c_e1_0p82>;
+ vdda-pll-supply = <&vreg_l4f_e1_1p08>;
+
+ status = "okay";
+};
+
+&pcie4_port0 {
+ reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+};
+
+&pcie5 {
+ vddpe-3v3-supply = <&vreg_nvme>;
+
+ pinctrl-0 = <&pcie5_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie5_phy {
+ vdda-phy-supply = <&vreg_l2f_e0_0p82>;
+ vdda-pll-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&pcie5_port0 {
+ reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+};
+
+&pcie6 {
+ vddpe-3v3-supply = <&vreg_wwan>;
+
+ pinctrl-0 = <&pcie6_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie6_phy {
+ vdda-phy-supply = <&vreg_l1c_e1_0p82>;
+ vdda-pll-supply = <&vreg_l4f_e1_1p08>;
+
+ status = "okay";
+};
+
+&pcie6_port0 {
+ reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;
+};
--
2.34.1
Powered by blists - more mailing lists