netdev - Re: [linux-pm] [PATCH 0/4] Fix forcedeth hibernate/wake-on-lan problems

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Date:	Tue, 3 Jun 2008 19:30:13 +0200
From:	Tobias Diedrich <ranma+kernel@...edrich.de>
To:	Alan Stern <stern@...land.harvard.edu>
Cc:	netdev@...r.kernel.org, linux-kernel@...r.kernel.org,
	Ayaz Abdulla <aabdulla@...dia.com>,
	"Rafael J. Wysocki" <rjw@...k.pl>,
	Stephen Hemminger <shemminger@...ux-foundation.org>,
	David Brownell <david-b@...bell.net>,
	linux-acpi@...r.kernel.org, linux-pm@...ts.linux-foundation.org
Subject: Re: [linux-pm] [PATCH 0/4] Fix forcedeth hibernate/wake-on-lan
	problems

Alan Stern wrote:
> > > Also, you should run "lspci -vv" as root to see what wakeup signals the 
> > > USB controllers are issuing.
[...]
> > 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) (prog-if 20 [EHCI])
> > 	Subsystem: ASUSTeK Computer Inc. Unknown device 8239
> > 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> > 	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> > 	Latency: 0 (750ns min, 250ns max)
> > 	Interrupt: pin B routed to IRQ 20
> > 	Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
> > 	Capabilities: [44] Debug port: BAR=1 offset=0098
> > 	Capabilities: [80] Power Management version 2
> > 		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> > 		Status: D0 PME-Enable- DSel=0 DScale=0 PME+
> > 	Kernel driver in use: ehci_hcd
> 
> The EHCI controller settings, however, are strange.  The relevant part 
> is the Power Management Status line near the end:
> 
> > 		Status: D0 PME-Enable- DSel=0 DScale=0 PME+
> 
> This means the controller is in the D0 state (as expected) and 
> PME-Enable is currently turned off ("PME" stands for "Power Management 
> Event").  But the PME+ at the end means that as soon as PME does get 
> enabled -- like when the controller is suspended at the start of a 
> system sleep -- it _will_ send a PME signal.
> 
> So for some reason your EHCI controller thinks a wakeup event is 
> pending.  This means you should examine the contents of the "registers" 
> file in the debugfs directory for the EHCI controller, not OHCI.

melchior:/mnt/ehci/0000:00:02.1# cat registers
bus pci, device 0000:00:02.1 (driver 10 Dec 2004)
EHCI Host Controller
EHCI 1.00, hcd state 1
ownership 00000001
SMI sts/enable 0xc0080000
structural params 0x00101a8a
capability params 0x0000a086
status 0008 FLR
command 010009 (park)=0 ithresh=1 period=256 RUN
intrenable 37 IAA FATAL PCD ERR INT
uframe 3f3a
port 1 status 003400 POWER OWNER sig=k
port 2 status 001000 POWER sig=se0
port 3 status 003400 POWER OWNER sig=k
port 4 status 003400 POWER OWNER sig=k
port 5 status 001000 POWER sig=se0
port 6 status 001000 POWER sig=se0
port 7 status 001000 POWER sig=se0
port 8 status 001000 POWER sig=se0
port 9 status 001000 POWER sig=se0
port 10 status 001000 POWER sig=se0
irq normal 0 err 0 reclaim 0 (lost 0)
complete 0 unlink 0

HTH,

-- 
Tobias						PGP: http://9ac7e0bc.uguu.de
このメールは十割再利用されたビットで作られています。
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html