| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <19211.4476.998509.26326@gargle.gargle.HOWL> Date: Mon, 23 Nov 2009 23:49:32 +0100 From: Robert Olsson <robert@...julf.net> To: David Miller <davem@...emloft.net> Cc: netdev@...r.kernel.org, Robert Olsson <robert@...julf.net> Subject: Diagnostic Monitoring Interface Monitoring (DOM) PATCH 1/5 for net-next-2.6 Signed-off-by: Robert Olsson <robert.olsson@....uu.se> diff --git a/Documentation/networking/dom.txt b/Documentation/networking/dom.txt new file mode 100644 index 0000000..ff255b4 --- /dev/null +++ b/Documentation/networking/dom.txt @@ -0,0 +1,41 @@ +Diagnostic Monitoring Interface Monitoring also called DOM is a specification +for optical transceivers to allow link and other diagnostics related to the +transceiver's to standardized and communicated. For communication the I2C +bus is used. The SFF specifications is available at ftp://ftp.seagate.com/ +Specification is generic and should work for many types of optical modules +as GBIC, SFP, SFp+, XFP etc + +In short DOM spec adds a memory page where the diagnostics's is kept (address +0xA2 bytes 66 to 105) but there are lot's of option's and variants. For example +alarm and warnings are optional. See example below. + +Not all SFP's (SFP is for GIGE) have DOM support normally long range supports +DOM. And of course your board and driver needs this support too. +For SFP+ (10G) DOM is mandatory. + +Linux kernel support is via ethertool. + +include/net/dom.h # Basic definitions +net/core/ethtool.c # adds ethtool_phy_diag() +include/linux/ethtool.h # adds ETHTOOL_GPHYDIAG + +And drivers hooks exists currently in igb and ixgbe driver + +Usage example: ethtool -D eth5 + +Ext-Calbr: Avr RX-Power: Alarm & Warn: RX_LOS: Wavelength: 1310 nm +Alarms, warnings in beginning of line, Ie. AH = Alarm High, WL == Warn Low etc + Temp: 35.9 C Thresh: Lo: -12.0/-8.0 Hi: 103.0/110.0 C + Vcc: 3.33 V Thresh: Lo: 3.0/3.0 Hi: 3.7/4.0 V + Tx-Bias: 13.4 mA Thresh: Lo: 2.0/4.0 Hi: 70.0/84.0 mA +ALWL TX-pwr: -5.9 dBm ( 0.26 mW) Thresh: Lo: -4.0/-2.0 Hi: 7.0/8.2 dBm +AHWH RX-pwr: -5.0 dBm ( 0.31 mW) Thresh: Lo: -35.2/-28.0 Hi: -8.2/-6.0 dBm + + +First line shows the options supported by the module. As we see this module +supports Alarms and warnings as a consequence thresholds are printed. As example +RX-pwr: -35.2 < no_alarm < -6.0 dBm and -28.0 < no_warning < -8.2 dBm. (dBm yields +1 mW == 0 dBm) + +In the example above we see both warnings for both TX-pwr (low) and RX-Pwr high. +The Rx side would need some attenuation. diff --git a/include/net/dom.h b/include/net/dom.h new file mode 100644 index 0000000..4c118a9 --- /dev/null +++ b/include/net/dom.h @@ -0,0 +1,109 @@ +#ifndef _LINUX_DOM_H +#define _LINUX_DOM_H + +/* + Diagnostic Monitoring Interface for Optical Tranceivers + SFF-8472 v. 10.4 (Jan 2009) + ftp://ftp.seagate.com/sff/SFF-8472.PDF + + Licensce GPL. Copyright Robert Olsson robert@...julf.net +*/ + +#define DOM_A0_IDENTIFIER 0 +#define DOM_A0_WAVELENGTH 60 +#define DOM_A0_CC_BASE 63 +#define DOM_A0_DOM_TYPE 92 + +/* DOM_TYPE codings in DOM_A0_DOM_TYPE */ +#define DOM_TYPE_LEGAGY_DOM (1<<7) +#define DOM_TYPE_DOM (1<<6) /* Has DOM support */ +#define DOM_TYPE_INT_CAL (1<<5) /* Internally calibrated */ +#define DOM_TYPE_EXT_CAL (1<<4) /* Externally calibrated */ +#define DOM_TYPE_RX_PWR (1<<3) /* Received Power OMA=0, 1=average */ +#define DOM_TYPE_ADDR_CHNGE (1<<2) /* Address change required */ + +#define DOM_A0_EO 93 /* Enhanced options */ +#define DOM_EO_AW (1<<7) /* Alarm & Warnings */ +#define DOM_EO_TX_DISABLE (1<<6) +#define DOM_EO_TX_FAULT (1<<5) +#define DOM_EO_RX_LOS (1<<4) +#define DOM_EO_RATE_SELECT_MON (1<<3) +#define DOM_EO_APP_SELECT (1<<2) +#define DOM_EO_RATE_SELECT (1<<1) + +#define DOM_A0_CC_EXT 95 + +#define DOM_A2_TEMP_AHT 0 /* Temp alarm high threshold */ +#define DOM_A2_TEMP_ALT 2 +#define DOM_A2_TEMP_WHT 4 /* Temp warning high threshold */ +#define DOM_A2_TEMP_WLT 6 + +#define DOM_A2_VCC_AHT 8 /* VCC alarm high threshold */ +#define DOM_A2_VCC_ALT 10 +#define DOM_A2_VCC_WHT 12 /* VCC warning high threshold */ +#define DOM_A2_VCC_WLT 14 + +#define DOM_A2_TX_BIAS_AHT 16 /* TX_BIAS alarm high threshold */ +#define DOM_A2_TX_BIAS_ALT 18 +#define DOM_A2_TX_BIAS_WHT 20 /* TX_BIAS warning high threshold */ +#define DOM_A2_TX_BIAS_WLT 22 + +#define DOM_A2_TX_PWR_AHT 24 /* TX_PWR alarm high threshold */ +#define DOM_A2_TX_PWR_ALT 26 +#define DOM_A2_TX_PWR_WHT 28 /* TX_PWR warning high threshold */ +#define DOM_A2_TX_PWR_WLT 30 + +#define DOM_A2_RX_PWR_AHT 32 /* RX_PWR alarm high threshold */ +#define DOM_A2_RX_PWR_ALT 34 +#define DOM_A2_RX_PWR_WHT 36 /* RX_PWR warning high threshold */ +#define DOM_A2_RX_PWR_WLT 38 + +#define DOM_A2_RX_PWR_4 56 /* 4 bytes Calibration constants*/ +#define DOM_A2_RX_PWR_3 60 /* 4 bytes */ +#define DOM_A2_RX_PWR_2 64 /* 4 bytes */ +#define DOM_A2_RX_PWR_1 68 /* 4 bytes */ +#define DOM_A2_RX_PWR_0 72 /* 4 bytes */ + +#define DOM_A2_TX_I_SLOPE 76 /* 2 bytes */ +#define DOM_A2_TX_I_OFFSET 78 /* 2 bytes */ +#define DOM_A2_TX_PWR_SLOPE 80 /* 2 bytes */ +#define DOM_A2_TX_PWR_OFFSET 82 /* 2 bytes */ +#define DOM_A2_TEMP_SLOPE 84 /* 2 bytes */ +#define DOM_A2_TEMP_OFFSET 86 /* 2 bytes */ +#define DOM_A2_VCC_SLOPE 88 /* 2 bytes */ +#define DOM_A2_VCC_OFFSET 90 /* 2 bytes */ + +#define DOM_A2_CC_DMI 95 +#define DOM_A2_TEMP 96 /* 2 bytes */ +#define DOM_A2_VCC 98 /* 2 bytes */ +#define DOM_A2_TX_BIAS 100 /* 2 bytes */ +#define DOM_A2_TX_PWR 102 /* 2 bytes */ +#define DOM_A2_RX_PWR 104 /* 2 bytes */ + +#define DOM_A2_ALARM 112 /* 2 bytes */ +#define DOM_TYPE_TEMP_AH (1<<7) /* Temp alarm high */ +#define DOM_TYPE_TEMP_AL (1<<6) /* low */ +#define DOM_TYPE_VCC_AH (1<<5) +#define DOM_TYPE_VCC_AL (1<<4) +#define DOM_TYPE_TX_BIAS_AH (1<<3) +#define DOM_TYPE_TX_BIAS_AL (1<<2) +#define DOM_TYPE_TX_PWR_AH (1<<1) +#define DOM_TYPE_TX_PWR_AL (1<<0) +/* Next byte 113 */ +#define DOM_TYPE_RX_PWR_AH (1<<7) +#define DOM_TYPE_RX_PWR_AL (1<<6) + +#define DOM_A2_WARNING 116 /* 2 bytes */ +#define DOM_TYPE_TEMP_WH (1<<7) /* Temp warning high */ +#define DOM_TYPE_TEMP_WL (1<<6) /* low */ +#define DOM_TYPE_VCC_WH (1<<5) +#define DOM_TYPE_VCC_WL (1<<4) +#define DOM_TYPE_TX_BIAS_WH (1<<3) +#define DOM_TYPE_TX_BIAS_WL (1<<2) +#define DOM_TYPE_TX_PWR_WH (1<<1) +#define DOM_TYPE_TX_PWR_WL (1<<0) +/* Next byte 117 */ +#define DOM_TYPE_RX_PWR_WH (1<<7) +#define DOM_TYPE_RX_PWR_WL (1<<6) + +#endif /* _LINUX_DOM_H */ -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists