| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Mon, 4 Feb 2013 10:37:32 +0530
From: Prabhakar Lad <prabhakar.csengg@...il.com>
To: Sekhar Nori <nsekhar@...com>
Cc: linux-arm-kernel@...ts.infradead.org,
davinci-linux-open-source@...ux.davincidsp.com,
linux-kernel@...r.kernel.org, netdev@...r.kernel.org,
devicetree-discuss@...ts.ozlabs.org, Heiko Schocher <hs@...x.de>,
"Lad, Prabhakar" <prabhakar.lad@...com>
Subject: Re: [PATCH v2 4/6] ARM: davinci: da850: add DT node for eth0.
Sekhar ,
On Sun, Feb 3, 2013 at 5:33 PM, Sekhar Nori <nsekhar@...com> wrote:
> On 1/28/2013 7:17 PM, Prabhakar Lad wrote:
>> From: Lad, Prabhakar <prabhakar.lad@...com>
>>
>> Add eth0 device tree node information and pinmux for mii to da850 by
>> providing interrupt details and local mac address of eth0.
>>
>> Signed-off-by: Lad, Prabhakar <prabhakar.lad@...com>
>> Cc: linux-arm-kernel@...ts.infradead.org
>> Cc: linux-kernel@...r.kernel.org
>> Cc: davinci-linux-open-source@...ux.davincidsp.com
>> Cc: netdev@...r.kernel.org
>> Cc: devicetree-discuss@...ts.ozlabs.org
>> Cc: Sekhar Nori <nsekhar@...com>
>> Cc: Heiko Schocher <hs@...x.de>
>> ---
>> arch/arm/boot/dts/da850-evm.dts | 5 +++++
>> arch/arm/boot/dts/da850.dtsi | 35 +++++++++++++++++++++++++++++++++++
>> 2 files changed, 40 insertions(+), 0 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
>> index a319491..19aa2b3 100644
>> --- a/arch/arm/boot/dts/da850-evm.dts
>> +++ b/arch/arm/boot/dts/da850-evm.dts
>> @@ -30,6 +30,11 @@
>> mdio: davinci_mdio@...4000 {
>> status = "okay";
>> };
>> + eth0: emac@...0000 {
>> + status = "okay";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mii_pins>;
>> + };
>> };
>> nand_cs3@...00000 {
>> status = "okay";
>> diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
>> index ba28f2d..76905f3 100644
>> --- a/arch/arm/boot/dts/da850.dtsi
>> +++ b/arch/arm/boot/dts/da850.dtsi
>> @@ -56,6 +56,26 @@
>> 0x30 0x01100000 0x0ff00000
>> >;
>> };
>> + mii_pins: pinmux_mii_pins {
>> + pinctrl-single,bits = <
>> + /*
>> + * MII_TXEN, MII_TXCLK, MII_COL
>> + * MII_TXD_3, MII_TXD_2, MII_TXD_1
>> + * MII_TXD_0
>> + */
>> + 0x8 0x88888880 0xfffffff0
>> + /*
>> + * MII_RXER, MII_CRS, MII_RXCLK
>> + * MII_RXDV, MII_RXD_3, MII_RXD_2
>> + * MII_RXD_1, MII_RXD_0
>> + */
>> + 0xc 0x88888888 0xffffffff
>> + /* MDIO_CLK, MDIO_D */
>
> You call this mii_pins, but include mdio pins in there as well. Can you
> separate them out? Then some board which uses rmii can simply reuse the
> entry.
>
Ok makes sense.
>> + 0x10 0x00222288 0x00ffffff
>> + /* GPIO2_6 */
>> + 0x18 0x00000080 0x000000f0
>
> This is SoC specific pin list. Such board specific pins should not make
> it here.
>
Ok, so this should be set up using GPIO API's ?
>> + >;
>> + };
>> };
>> serial0: serial@...2000 {
>> compatible = "ns16550a";
>> @@ -88,6 +108,21 @@
>> reg = <0x224000 0x1000>;
>> bus_freq = <2200000>;
>> };
>> + eth0: emac@...0000 {
>> + compatible = "ti,davinci-dm6467-emac";
>> + reg = <0x220000 0x4000>;
>> + ti,davinci-ctrl-reg-offset = <0x3000>;
>> + ti,davinci-ctrl-mod-reg-offset = <0x2000>;
>> + ti,davinci-ctrl-ram-offset = <0>;
>> + ti,davinci-ctrl-ram-size = <0x2000>;
>> + local-mac-address = [ 00 00 00 00 00 00 ];
>> + interrupts = <33
>> + 34
>> + 35
>> + 36
>> + >;
>> + phy-handle = <&mdio>;
>
> I doubt this is required. This property is to pass a handle to the phy,
> not mdio bus.
>
Ok I'll check on this.
Regards,
--Prabhakar
> Thanks,
> Sekhar
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Powered by blists - more mailing lists