netdev - Re: Micrel Phy - Is there a way to configure the Phy not to do 802.3x flow control?

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <56E321DE.9030408@gmail.com>
Date:	Fri, 11 Mar 2016 11:51:58 -0800
From:	Florian Fainelli <f.fainelli@...il.com>
To:	Murali Karicheri <m-karicheri2@...com>, johan@...nel.org,
	"open list:TI NETCP ETHERNET DRIVER" <netdev@...r.kernel.org>,
	"Kwok, WingMan" <w-kwok2@...com>, Andrew Lunn <andrew@...nc.ch>,
	opendmb@...il.com
Subject: Re: Micrel Phy - Is there a way to configure the Phy not to do 802.3x
 flow control?

On 11/03/16 10:31, Murali Karicheri wrote:
> On 03/10/2016 02:38 PM, Murali Karicheri wrote:
>> On 03/10/2016 01:05 PM, Florian Fainelli wrote:
>>> On 10/03/16 08:48, Murali Karicheri wrote:
>>>> On 03/03/2016 07:16 PM, Florian Fainelli wrote:
>>>>> On 03/03/16 14:18, Murali Karicheri wrote:
>>>>>> Hi,
>>>>>>
>>>>>> We are using Micrel Phy in one of our board and wondering if we can force the
>>>>>> Phy to disable flow control at start. I have a 1G ethernet switch connected
>>>>>> to Phy and the phy always enable flow control. I would like to configure the
>>>>>> phy not to flow control. Is that possible and if yes, what should I do in the
>>>>>> my Ethernet driver to tell the Phy not to enable flow control?
>>>>>
>>>>> The PHY is not doing flow control per-se, your pseudo Ethernet MAC in
>>>>> the switch is doing, along with the link partner advertising support for
>>>>> it. You would want to make sure that your PHY device interface (provided
>>>>> that you are using the PHY library) is not starting with Pause
>>>>> advertised, but it could be supported.
>>>>
>>>> Understood that Phy is just advertise FC. The Micrel phy for 9031 advertise
>>>> by default FC supported. After negotiation, I see that Phylib provide the 
>>>> link status with parameter pause = 1, asym_pause = 1. How do I tell the Phy not
>>>> to advertise?
>>>>
>>>> I call following sequence in the Ethernet driver.
>>>>
>>>> of_phy_connect(x,y,hndlr,a,z);
>>>
>>> Here you should be able to change phydev->advertising and
>>> phydev->supported to mask the ADVERTISED_Pause | ADVERTISED_AsymPause
>>> bits and have phy_start() restart with that which should disable pause
>>> and asym_pause as seen by your adjust_link handler.
>>>
>> Ok. Good point. I will try this. Thanks for your suggestion.
>>
> I had to make following changes to the phy_device.c to allow the phy device
> report maximum common flow control capability to Ethernet driver through
> handler. My driver code looks like this.
> 
>                 slave->phy = of_phy_connect(gbe_intf->ndev,
>                                             slave->phy_node,
>                                             hndlr, 0,
>                                             phy_mode);
>                 if (!slave->phy) {
>                         dev_err(priv->dev, "phy not found on slave %d\n",
>                                 slave->slave_num);
>                         return -ENODEV;
>                 }
>                 dev_dbg(priv->dev, "phy found: id is: 0x%s\n",
>                         dev_name(&slave->phy->dev));
> 
>                 slave->phy->supported &=
>                                 ~(SUPPORTED_Pause | SUPPORTED_Asym_Pause);
>                 slave->phy->advertising = slave->phy->supported;
>                 phy_start(slave->phy);
>                 phy_read_status(slave->phy);
> 
> And then in the phy_device.c, I did to get flow control off reported in
> handler for link status update.



> 
> diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
> index d551df6..55412ad 100644
> --- a/drivers/net/phy/phy_device.c
> +++ b/drivers/net/phy/phy_device.c
> @@ -1021,8 +1021,8 @@ int genphy_read_status(struct phy_device *phydev)
>                                 phydev->duplex = DUPLEX_FULL;
>  
>                 if (phydev->duplex == DUPLEX_FULL) {
> -                       phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0;
> -                       phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0;
> +                       phydev->pause = adv & lpa & LPA_PAUSE_CAP ? 1 : 0;
> +                       phydev->asym_pause = adv & lpa & LPA_PAUSE_ASYM ? 1 : 0;

What it means before your patch is that flow control is reported to the
PHY device if the link partner advertises that, with your patch applied,
it is reported only if the link partner and yourself advertise flow control.

You seem to be willing to have phydev->pause and phydev->asym_pause
reflect the resolved pause capability, as opposed to the link partner's
pause capability, which I am not convinced is correct here, because we
need to take into account the user-configured pause configuration as
well. Your adjust_link function should be the one deciding whether pause
frame advertising and enabling is appropriate based on: locally
configured pause settings (enabled, disabled, autoneg) and the link
partner's pause capability.

I do agree that the two fields are confusing and poorly documented, and
we should probably be consolidating the pause frame behavior in PHYLIB
as opposed to letting drivers deal with like e.g: gianfar, bcm63xx_enet,
tg3 etc.

>  
> Could you explain, why the common maximum capability is not reported to the
> driver as per standard?? Or Am I understood it wrong?

I do not understand the question, what is "maximum capability" in that
context and what standard are you refering to?
-- 
Florian