netdev - Re: Micrel Phy - Is there a way to configure the Phy not to do 802.3x flow control?

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <56E30EE5.4050904@ti.com>
Date:	Fri, 11 Mar 2016 13:31:01 -0500
From:	Murali Karicheri <m-karicheri2@...com>
To:	Florian Fainelli <f.fainelli@...il.com>, <johan@...nel.org>,
	"open list:TI NETCP ETHERNET DRIVER" <netdev@...r.kernel.org>,
	"Kwok, WingMan" <w-kwok2@...com>
Subject: Re: Micrel Phy - Is there a way to configure the Phy not to do 802.3x
 flow control?

On 03/10/2016 02:38 PM, Murali Karicheri wrote:
> On 03/10/2016 01:05 PM, Florian Fainelli wrote:
>> On 10/03/16 08:48, Murali Karicheri wrote:
>>> On 03/03/2016 07:16 PM, Florian Fainelli wrote:
>>>> On 03/03/16 14:18, Murali Karicheri wrote:
>>>>> Hi,
>>>>>
>>>>> We are using Micrel Phy in one of our board and wondering if we can force the
>>>>> Phy to disable flow control at start. I have a 1G ethernet switch connected
>>>>> to Phy and the phy always enable flow control. I would like to configure the
>>>>> phy not to flow control. Is that possible and if yes, what should I do in the
>>>>> my Ethernet driver to tell the Phy not to enable flow control?
>>>>
>>>> The PHY is not doing flow control per-se, your pseudo Ethernet MAC in
>>>> the switch is doing, along with the link partner advertising support for
>>>> it. You would want to make sure that your PHY device interface (provided
>>>> that you are using the PHY library) is not starting with Pause
>>>> advertised, but it could be supported.
>>>
>>> Understood that Phy is just advertise FC. The Micrel phy for 9031 advertise
>>> by default FC supported. After negotiation, I see that Phylib provide the 
>>> link status with parameter pause = 1, asym_pause = 1. How do I tell the Phy not
>>> to advertise?
>>>
>>> I call following sequence in the Ethernet driver.
>>>
>>> of_phy_connect(x,y,hndlr,a,z);
>>
>> Here you should be able to change phydev->advertising and
>> phydev->supported to mask the ADVERTISED_Pause | ADVERTISED_AsymPause
>> bits and have phy_start() restart with that which should disable pause
>> and asym_pause as seen by your adjust_link handler.
>>
> Ok. Good point. I will try this. Thanks for your suggestion.
> 
I had to make following changes to the phy_device.c to allow the phy device
report maximum common flow control capability to Ethernet driver through
handler. My driver code looks like this.

                slave->phy = of_phy_connect(gbe_intf->ndev,
                                            slave->phy_node,
                                            hndlr, 0,
                                            phy_mode);
                if (!slave->phy) {
                        dev_err(priv->dev, "phy not found on slave %d\n",
                                slave->slave_num);
                        return -ENODEV;
                }
                dev_dbg(priv->dev, "phy found: id is: 0x%s\n",
                        dev_name(&slave->phy->dev));

                slave->phy->supported &=
                                ~(SUPPORTED_Pause | SUPPORTED_Asym_Pause);
                slave->phy->advertising = slave->phy->supported;
                phy_start(slave->phy);
                phy_read_status(slave->phy);

And then in the phy_device.c, I did to get flow control off reported in
handler for link status update.

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index d551df6..55412ad 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1021,8 +1021,8 @@ int genphy_read_status(struct phy_device *phydev)
                                phydev->duplex = DUPLEX_FULL;
 
                if (phydev->duplex == DUPLEX_FULL) {
-                       phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0;
-                       phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0;
+                       phydev->pause = adv & lpa & LPA_PAUSE_CAP ? 1 : 0;
+                       phydev->asym_pause = adv & lpa & LPA_PAUSE_ASYM ? 1 : 0;
 
Could you explain, why the common maximum capability is not reported to the
driver as per standard?? Or Am I understood it wrong?

Murali

> Murali
>>> phy_start()
>>>
>>> Now in hndlr() I have pause = 1, asym_pause = 1, in phy_device ptr. How can 
>>> I tell the phy not to advertise initially?
> 
> 


-- 
Murali Karicheri
Linux Kernel, Keystone