netdev - [RFT net-next v3 4/5] net: stmmac: dwmac-meson8b: fix setting the RGMII clock on Meson8b

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20171228222128.15215-5-martin.blumenstingl@googlemail.com>
Date:   Thu, 28 Dec 2017 23:21:27 +0100
From:   Martin Blumenstingl <martin.blumenstingl@...glemail.com>
To:     netdev@...r.kernel.org, ingrassia@...genesys.com
Cc:     linus.luessing@...3.blue, khilman@...libre.com,
        linux-amlogic@...ts.infradead.org, jbrunet@...libre.com,
        narmstrong@...libre.com, peppe.cavallaro@...com,
        alexandre.torgue@...com,
        Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Subject: [RFT net-next v3 4/5] net: stmmac: dwmac-meson8b: fix setting the RGMII clock on Meson8b

Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to 500MHz. The exact rate is
500002394Hz, which is calculated in drivers/clk/meson/clk-mpll.c
using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5

The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 25MHz clock.

Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate of 25000120Hz (= 25MHz
plus 120Hz).
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 25MHz).

Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@...genesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Reviewed-by: Jerome Brunet <jbrunet@...libre.com>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
index 7199e8c08536..d06106417063 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -139,7 +139,9 @@ static int meson8b_init_rgmii_clk(struct meson8b_dwmac *dwmac)
 	dwmac->m250_div.shift = PRG_ETH0_CLK_M250_DIV_SHIFT;
 	dwmac->m250_div.width = PRG_ETH0_CLK_M250_DIV_WIDTH;
 	dwmac->m250_div.hw.init = &init;
-	dwmac->m250_div.flags = CLK_DIVIDER_ONE_BASED | CLK_DIVIDER_ALLOW_ZERO;
+	dwmac->m250_div.flags = CLK_DIVIDER_ONE_BASED |
+				CLK_DIVIDER_ALLOW_ZERO |
+				CLK_DIVIDER_ROUND_CLOSEST;
 
 	dwmac->m250_div_clk = devm_clk_register(dev, &dwmac->m250_div.hw);
 	if (WARN_ON(IS_ERR(dwmac->m250_div_clk)))
-- 
2.15.1