| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <A1527477-EC6E-4B64-880F-B014E8CFCB9D@gmail.com>
Date: Wed, 2 Oct 2019 17:35:23 +0100
From: Rudolf Spring <rudolf.spring@...il.com>
To: Michael Chan <michael.chan@...adcom.com>
Cc: Siva Reddy Kallam <siva.kallam@...adcom.com>,
Netdev <netdev@...r.kernel.org>
Subject: Re: Gentoo Linux 5.x - Tigon3
The output of dmesg and ethtool is identical between 4.19.72 and 5.3.2. Any suggestions ?
0000:01:00.0: enabling device (0000 -> 0002)
[ 1.140738] tg3 0000:01:00.0 eth0: Tigon3 [partno(BCM957766a) rev 57766001] (PCI Express) MAC address a8:20:66:28:e6:95
[ 1.140741] tg3 0000:01:00.0 eth0: attached PHY is 57765 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
[ 1.140743] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.140744] tg3 0000:01:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
[ 10.290239] tg3 0000:01:00.0 eth0: Link is up at 1000 Mbps, full duplex
[ 10.290241] tg3 0000:01:00.0 eth0: Flow control is on for TX and on for RX
[ 10.290242] tg3 0000:01:00.0 eth0: EEE is enabled
ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: off
Supports Wake-on: g
Wake-on: g
Current message level: 0x000000ff (255)
drv probe link timer ifdown ifup rx_err tx_err
Link detected: yes
ethtool -a eth0
Pause parameters for eth0:
Autonegotiate: on
RX: on
TX: on
RX negotiated: on
TX negotiated: on
ethtool -g eth0
Ring parameters for eth0:
Pre-set maximums:
RX: 511
RX Mini: 0
RX Jumbo: 255
TX: 511
Current hardware settings:
RX: 200
RX Mini: 0
RX Jumbo: 100
TX: 511
ethtool -c eth0
Coalesce parameters for eth0:
Adaptive RX: off TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 20
rx-frames: 5
rx-usecs-irq: 0
rx-frames-irq: 5
tx-usecs: 72
tx-frames: 53
tx-usecs-irq: 0
tx-frames-irq: 5
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
ethtool -k eth0
Features for eth0:
rx-checksumming: on
tx-checksumming: on
tx-checksum-ipv4: on
tx-checksum-ip-generic: off [fixed]
tx-checksum-ipv6: on
tx-checksum-fcoe-crc: off [fixed]
tx-checksum-sctp: off [fixed]
scatter-gather: on
tx-scatter-gather: on
tx-scatter-gather-fraglist: off [fixed]
tcp-segmentation-offload: on
tx-tcp-segmentation: on
tx-tcp-ecn-segmentation: on
tx-tcp-mangleid-segmentation: off
tx-tcp6-segmentation: on
udp-fragmentation-offload: off
generic-segmentation-offload: on
generic-receive-offload: on
large-receive-offload: off [fixed]
rx-vlan-offload: on [fixed]
tx-vlan-offload: on [fixed]
ntuple-filters: off [fixed]
receive-hashing: off [fixed]
highdma: on
rx-vlan-filter: off [fixed]
vlan-challenged: off [fixed]
tx-lockless: off [fixed]
netns-local: off [fixed]
tx-gso-robust: off [fixed]
tx-fcoe-segmentation: off [fixed]
tx-gre-segmentation: off [fixed]
tx-gre-csum-segmentation: off [fixed]
tx-ipxip4-segmentation: off [fixed]
tx-ipxip6-segmentation: off [fixed]
tx-udp_tnl-segmentation: off [fixed]
tx-udp_tnl-csum-segmentation: off [fixed]
tx-gso-partial: off [fixed]
tx-sctp-segmentation: off [fixed]
tx-esp-segmentation: off [fixed]
tx-udp-segmentation: off [fixed]
fcoe-mtu: off [fixed]
tx-nocache-copy: off
loopback: off [fixed]
rx-fcs: off [fixed]
rx-all: off [fixed]
tx-vlan-stag-hw-insert: off [fixed]
rx-vlan-stag-hw-parse: off [fixed]
rx-vlan-stag-filter: off [fixed]
l2-fwd-offload: off [fixed]
hw-tc-offload: off [fixed]
esp-hw-offload: off [fixed]
esp-tx-csum-hw-offload: off [fixed]
rx-udp_tunnel-port-offload: off [fixed]
tls-hw-tx-offload: off [fixed]
tls-hw-rx-offload: off [fixed]
rx-gro-hw: off [fixed]
tls-hw-record: off [fixed]
ethtool -n eth0
4 RX rings available
rxclass: Cannot get RX class rule count: Operation not supported
RX classification rule retrieval failed
ethtool -t eth0
The test result is PASS
The test extra info:
nvram test (online) 0
link test (online) 0
register test (offline) 0
memory test (offline) 0
mac loopback test (offline) 0
phy loopback test (offline) 0
ext loopback test (offline) 0
interrupt test (offline) 0
ethtool -T eth0
Time stamping parameters for eth0:
Capabilities:
software-transmit (SOF_TIMESTAMPING_TX_SOFTWARE)
software-receive (SOF_TIMESTAMPING_RX_SOFTWARE)
software-system-clock (SOF_TIMESTAMPING_SOFTWARE)
PTP Hardware Clock: none
Hardware Transmit Timestamp Modes:
off (HWTSTAMP_TX_OFF)
on (HWTSTAMP_TX_ON)
Hardware Receive Filter Modes:
none (HWTSTAMP_FILTER_NONE)
ptpv1-l4-event (HWTSTAMP_FILTER_PTP_V1_L4_EVENT)
ptpv2-l4-event (HWTSTAMP_FILTER_PTP_V2_L4_EVENT)
ptpv2-l2-event (HWTSTAMP_FILTER_PTP_V2_L2_EVENT)
ethtool -l eth0
Channel parameters for eth0:
Pre-set maximums:
RX: 4
TX: 1
Other: 0
Combined: 0
Current hardware settings:
RX: 4
TX: 1
Other: 0
Combined: 0
ethtool --show-eee eth0
EEE Settings for eth0:
EEE status: enabled - active
Tx LPI: 2047 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Link partner advertised EEE link modes: 100baseT/Full
1000baseT/Full
> These are all the tg3 changes between 4.19 and 5.0:
>
> 750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
> cddaf02bcb73 tg3: optionally use eth_platform_get_mac_address() to get
> mac address
> 3c1bcc8614db net: ethernet: Convert phydev advertize and supported
> from u32 to link mode
> 6fe42e228dc2 tg3: extend PTP gettime function to read system clock
> 310fc0513ea9 tg3: Fix fall-through annotations
> 22b7d29926b5 net: ethernet: Add helper to determine if pause
> configuration is supported
> 70814e819c11 net: ethernet: Add helper for set_pauseparam for Asym Pause
> af8d9bb2f2f4 net: ethernet: Add helper for MACs which support asym pause
> 04b7d41d8046 net: ethernet: Fix up drivers masking pause support
> 58056c1e1b0e net: ethernet: Use phy_set_max_speed() to limit advertised speed
>
> Most of the changes are related to PHY settings. I suggest that you
> check the link settings, including speed, pause, asym pause, etc
> between the working kernel and the non-working kernel to see if there
> are differences in the settings.
Powered by blists - more mailing lists