| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAMet4B6csj+6umj+h7mdPfz+rnLrOFYe6RBhVb+-ykiAwjxJUg@mail.gmail.com>
Date: Thu, 31 Oct 2019 17:19:36 +0530
From: Siva Reddy Kallam <siva.kallam@...adcom.com>
To: Rudolf Spring <rudolf.spring@...il.com>
Cc: Michael Chan <michael.chan@...adcom.com>,
Netdev <netdev@...r.kernel.org>
Subject: Re: Gentoo Linux 5.x - Tigon3
Tried reproducing local with 5.4.0-rc3 kernel and I couldn't observe the issue.
I used the internet for almost 15-20 mins and no MAC errors observed.
Can you please provide ethtool -i output? I will use the same f/w
version and try.
On Fri, Oct 18, 2019 at 12:21 PM Siva Reddy Kallam
<siva.kallam@...adcom.com> wrote:
>
> On Thu, Oct 17, 2019 at 11:03 PM Rudolf Spring <rudolf.spring@...il.com> wrote:
> >
> > Can you reproduce the error in the lab ? Same behaviour with Kernel 5.3.6.
> >
> Yes. We are trying to reproduce in our local lab. We will update once
> we have reproduction.
> >
> > eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 9000
> > ether a8:20:66:28:e6:95 txqueuelen 1000 (Ethernet)
> > RX packets 13844854 bytes 2298858755 (2.1 GiB)
> > RX errors 0 dropped 2 overruns 0 frame 0
> > TX packets 14831625 bytes 75684684566 (70.4 GiB)
> > TX errors 158 dropped 0 overruns 0 carrier 0 collisions 0
> > device interrupt 16
> >
> > tx_octets: 75686159197
> > tx_collisions: 0
> > tx_xon_sent: 0
> > tx_xoff_sent: 0
> > tx_flow_control: 0
> > tx_mac_errors: 158
> > tx_single_collisions: 0
> > tx_mult_collisions: 0
> > tx_deferred: 0
> > tx_excessive_collisions: 0
> > tx_late_collisions: 0
> > tx_collide_2times: 0
> > tx_collide_3times: 0
> > tx_collide_4times: 0
> > tx_collide_5times: 0
> > tx_collide_6times: 0
> > tx_collide_7times: 0
> > tx_collide_8times: 0
> > tx_collide_9times: 0
> > tx_collide_10times: 0
> > tx_collide_11times: 0
> > tx_collide_12times: 0
> > tx_collide_13times: 0
> > tx_collide_14times: 0
> > tx_collide_15times: 0
> > tx_ucast_packets: 14400082
> > tx_mcast_packets: 435104
> > tx_bcast_packets: 1542
> > tx_carrier_sense_errors: 0
> > tx_discards: 0
> > tx_errors: 0
> >
> >
> > > On 4 Oct 2019, at 14:53, Rudolf Spring <rudolf.spring@...il.com> wrote:
> > >
> > > With Kernel 5.3.2. Interesting all are tx_mac_errors.
> > >
> > > ifconfig eth0
> > > eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 9000
> > > ether a8:20:66:28:e6:95 txqueuelen 1000 (Ethernet)
> > > RX packets 1649204 bytes 775261068 (739.3 MiB)
> > > RX errors 0 dropped 0 overruns 0 frame 0
> > > TX packets 1144621 bytes 1241414276 (1.1 GiB)
> > > TX errors 369 dropped 0 overruns 0 carrier 0 collisions 0
> > > device interrupt 16
> > >
> > > ethtool -S eth0
> > > NIC statistics:
> > > rx_octets: 752756285
> > > rx_fragments: 0
> > > rx_ucast_packets: 1132211
> > > rx_mcast_packets: 128115
> > > rx_bcast_packets: 372162
> > > rx_fcs_errors: 0
> > > rx_align_errors: 0
> > > rx_xon_pause_rcvd: 0
> > > rx_xoff_pause_rcvd: 0
> > > rx_mac_ctrl_rcvd: 0
> > > rx_xoff_entered: 0
> > > rx_frame_too_long_errors: 0
> > > rx_jabbers: 0
> > > rx_undersize_packets: 0
> > > rx_in_length_errors: 0
> > > rx_out_length_errors: 0
> > > rx_64_or_less_octet_packets: 0
> > > rx_65_to_127_octet_packets: 0
> > > rx_128_to_255_octet_packets: 0
> > > rx_256_to_511_octet_packets: 0
> > > rx_512_to_1023_octet_packets: 0
> > > rx_1024_to_1522_octet_packets: 0
> > > rx_1523_to_2047_octet_packets: 0
> > > rx_2048_to_4095_octet_packets: 0
> > > rx_4096_to_8191_octet_packets: 0
> > > rx_8192_to_9022_octet_packets: 0
> > > tx_octets: 1236703101
> > > tx_collisions: 0
> > > tx_xon_sent: 0
> > > tx_xoff_sent: 0
> > > tx_flow_control: 0
> > > tx_mac_errors: 369
> > > tx_single_collisions: 0
> > > tx_mult_collisions: 0
> > > tx_deferred: 0
> > > tx_excessive_collisions: 0
> > > tx_late_collisions: 0
> > > tx_collide_2times: 0
> > > tx_collide_3times: 0
> > > tx_collide_4times: 0
> > > tx_collide_5times: 0
> > > tx_collide_6times: 0
> > > tx_collide_7times: 0
> > > tx_collide_8times: 0
> > > tx_collide_9times: 0
> > > tx_collide_10times: 0
> > > tx_collide_11times: 0
> > > tx_collide_12times: 0
> > > tx_collide_13times: 0
> > > tx_collide_14times: 0
> > > tx_collide_15times: 0
> > > tx_ucast_packets: 986854
> > > tx_mcast_packets: 146951
> > > tx_bcast_packets: 1117
> > > tx_carrier_sense_errors: 0
> > > tx_discards: 0
> > > tx_errors: 0
> > > dma_writeq_full: 0
> > > dma_write_prioq_full: 0
> > > rxbds_empty: 0
> > > rx_discards: 0
> > > rx_errors: 0
> > > rx_threshold_hit: 0
> > > dma_readq_full: 0
> > > dma_read_prioq_full: 0
> > > tx_comp_queue_full: 0
> > > ring_set_send_prod_index: 0
> > > ring_status_update: 0
> > > nic_irqs: 0
> > > nic_avoided_irqs: 0
> > > nic_tx_threshold_hit: 0
> > > mbuf_lwm_thresh_hit: 0
> > >
> > >> On 4 Oct 2019, at 12:52, Siva Reddy Kallam <siva.kallam@...adcom.com> wrote:
> > >>
> > >>
> > >>
> > >> On Wed, Oct 2, 2019 at 10:05 PM Rudolf Spring <rudolf.spring@...il.com> wrote:
> > >> The output of dmesg and ethtool is identical between 4.19.72 and 5.3.2. Any suggestions ?
> > >> Can you please provide the output of "ethtool -S eth0" command?
> > >> In the mean time, I will review the register dump and also try to reproduce in our lab.
> > >> 0000:01:00.0: enabling device (0000 -> 0002)
> > >> [ 1.140738] tg3 0000:01:00.0 eth0: Tigon3 [partno(BCM957766a) rev 57766001] (PCI Express) MAC address a8:20:66:28:e6:95
> > >> [ 1.140741] tg3 0000:01:00.0 eth0: attached PHY is 57765 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1])
> > >> [ 1.140743] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
> > >> [ 1.140744] tg3 0000:01:00.0 eth0: dma_rwctrl[00000001] dma_mask[64-bit]
> > >> [ 10.290239] tg3 0000:01:00.0 eth0: Link is up at 1000 Mbps, full duplex
> > >> [ 10.290241] tg3 0000:01:00.0 eth0: Flow control is on for TX and on for RX
> > >> [ 10.290242] tg3 0000:01:00.0 eth0: EEE is enabled
> > >>
> > >> ethtool eth0
> > >> Settings for eth0:
> > >> Supported ports: [ TP ]
> > >> Supported link modes: 10baseT/Half 10baseT/Full
> > >> 100baseT/Half 100baseT/Full
> > >> 1000baseT/Half 1000baseT/Full
> > >> Supported pause frame use: No
> > >> Supports auto-negotiation: Yes
> > >> Supported FEC modes: Not reported
> > >> Advertised link modes: 10baseT/Half 10baseT/Full
> > >> 100baseT/Half 100baseT/Full
> > >> 1000baseT/Half 1000baseT/Full
> > >> Advertised pause frame use: Symmetric
> > >> Advertised auto-negotiation: Yes
> > >> Advertised FEC modes: Not reported
> > >> Link partner advertised link modes: 10baseT/Half 10baseT/Full
> > >> 100baseT/Half 100baseT/Full
> > >> 1000baseT/Full
> > >> Link partner advertised pause frame use: Symmetric
> > >> Link partner advertised auto-negotiation: Yes
> > >> Link partner advertised FEC modes: Not reported
> > >> Speed: 1000Mb/s
> > >> Duplex: Full
> > >> Port: Twisted Pair
> > >> PHYAD: 1
> > >> Transceiver: internal
> > >> Auto-negotiation: on
> > >> MDI-X: off
> > >> Supports Wake-on: g
> > >> Wake-on: g
> > >> Current message level: 0x000000ff (255)
> > >> drv probe link timer ifdown ifup rx_err tx_err
> > >> Link detected: yes
> > >>
> > >> ethtool -a eth0
> > >> Pause parameters for eth0:
> > >> Autonegotiate: on
> > >> RX: on
> > >> TX: on
> > >> RX negotiated: on
> > >> TX negotiated: on
> > >>
> > >> ethtool -g eth0
> > >> Ring parameters for eth0:
> > >> Pre-set maximums:
> > >> RX: 511
> > >> RX Mini: 0
> > >> RX Jumbo: 255
> > >> TX: 511
> > >> Current hardware settings:
> > >> RX: 200
> > >> RX Mini: 0
> > >> RX Jumbo: 100
> > >> TX: 511
> > >>
> > >> ethtool -c eth0
> > >> Coalesce parameters for eth0:
> > >> Adaptive RX: off TX: off
> > >> stats-block-usecs: 0
> > >> sample-interval: 0
> > >> pkt-rate-low: 0
> > >> pkt-rate-high: 0
> > >>
> > >> rx-usecs: 20
> > >> rx-frames: 5
> > >> rx-usecs-irq: 0
> > >> rx-frames-irq: 5
> > >>
> > >> tx-usecs: 72
> > >> tx-frames: 53
> > >> tx-usecs-irq: 0
> > >> tx-frames-irq: 5
> > >>
> > >> rx-usecs-low: 0
> > >> rx-frame-low: 0
> > >> tx-usecs-low: 0
> > >> tx-frame-low: 0
> > >>
> > >> rx-usecs-high: 0
> > >> rx-frame-high: 0
> > >> tx-usecs-high: 0
> > >> tx-frame-high: 0
> > >>
> > >> ethtool -k eth0
> > >> Features for eth0:
> > >> rx-checksumming: on
> > >> tx-checksumming: on
> > >> tx-checksum-ipv4: on
> > >> tx-checksum-ip-generic: off [fixed]
> > >> tx-checksum-ipv6: on
> > >> tx-checksum-fcoe-crc: off [fixed]
> > >> tx-checksum-sctp: off [fixed]
> > >> scatter-gather: on
> > >> tx-scatter-gather: on
> > >> tx-scatter-gather-fraglist: off [fixed]
> > >> tcp-segmentation-offload: on
> > >> tx-tcp-segmentation: on
> > >> tx-tcp-ecn-segmentation: on
> > >> tx-tcp-mangleid-segmentation: off
> > >> tx-tcp6-segmentation: on
> > >> udp-fragmentation-offload: off
> > >> generic-segmentation-offload: on
> > >> generic-receive-offload: on
> > >> large-receive-offload: off [fixed]
> > >> rx-vlan-offload: on [fixed]
> > >> tx-vlan-offload: on [fixed]
> > >> ntuple-filters: off [fixed]
> > >> receive-hashing: off [fixed]
> > >> highdma: on
> > >> rx-vlan-filter: off [fixed]
> > >> vlan-challenged: off [fixed]
> > >> tx-lockless: off [fixed]
> > >> netns-local: off [fixed]
> > >> tx-gso-robust: off [fixed]
> > >> tx-fcoe-segmentation: off [fixed]
> > >> tx-gre-segmentation: off [fixed]
> > >> tx-gre-csum-segmentation: off [fixed]
> > >> tx-ipxip4-segmentation: off [fixed]
> > >> tx-ipxip6-segmentation: off [fixed]
> > >> tx-udp_tnl-segmentation: off [fixed]
> > >> tx-udp_tnl-csum-segmentation: off [fixed]
> > >> tx-gso-partial: off [fixed]
> > >> tx-sctp-segmentation: off [fixed]
> > >> tx-esp-segmentation: off [fixed]
> > >> tx-udp-segmentation: off [fixed]
> > >> fcoe-mtu: off [fixed]
> > >> tx-nocache-copy: off
> > >> loopback: off [fixed]
> > >> rx-fcs: off [fixed]
> > >> rx-all: off [fixed]
> > >> tx-vlan-stag-hw-insert: off [fixed]
> > >> rx-vlan-stag-hw-parse: off [fixed]
> > >> rx-vlan-stag-filter: off [fixed]
> > >> l2-fwd-offload: off [fixed]
> > >> hw-tc-offload: off [fixed]
> > >> esp-hw-offload: off [fixed]
> > >> esp-tx-csum-hw-offload: off [fixed]
> > >> rx-udp_tunnel-port-offload: off [fixed]
> > >> tls-hw-tx-offload: off [fixed]
> > >> tls-hw-rx-offload: off [fixed]
> > >> rx-gro-hw: off [fixed]
> > >> tls-hw-record: off [fixed]
> > >>
> > >> ethtool -n eth0
> > >> 4 RX rings available
> > >> rxclass: Cannot get RX class rule count: Operation not supported
> > >> RX classification rule retrieval failed
> > >>
> > >> ethtool -t eth0
> > >> The test result is PASS
> > >> The test extra info:
> > >> nvram test (online) 0
> > >> link test (online) 0
> > >> register test (offline) 0
> > >> memory test (offline) 0
> > >> mac loopback test (offline) 0
> > >> phy loopback test (offline) 0
> > >> ext loopback test (offline) 0
> > >> interrupt test (offline) 0
> > >>
> > >> ethtool -T eth0
> > >> Time stamping parameters for eth0:
> > >> Capabilities:
> > >> software-transmit (SOF_TIMESTAMPING_TX_SOFTWARE)
> > >> software-receive (SOF_TIMESTAMPING_RX_SOFTWARE)
> > >> software-system-clock (SOF_TIMESTAMPING_SOFTWARE)
> > >> PTP Hardware Clock: none
> > >> Hardware Transmit Timestamp Modes:
> > >> off (HWTSTAMP_TX_OFF)
> > >> on (HWTSTAMP_TX_ON)
> > >> Hardware Receive Filter Modes:
> > >> none (HWTSTAMP_FILTER_NONE)
> > >> ptpv1-l4-event (HWTSTAMP_FILTER_PTP_V1_L4_EVENT)
> > >> ptpv2-l4-event (HWTSTAMP_FILTER_PTP_V2_L4_EVENT)
> > >> ptpv2-l2-event (HWTSTAMP_FILTER_PTP_V2_L2_EVENT)
> > >>
> > >> ethtool -l eth0
> > >> Channel parameters for eth0:
> > >> Pre-set maximums:
> > >> RX: 4
> > >> TX: 1
> > >> Other: 0
> > >> Combined: 0
> > >> Current hardware settings:
> > >> RX: 4
> > >> TX: 1
> > >> Other: 0
> > >> Combined: 0
> > >>
> > >> ethtool --show-eee eth0
> > >> EEE Settings for eth0:
> > >> EEE status: enabled - active
> > >> Tx LPI: 2047 (us)
> > >> Supported EEE link modes: 100baseT/Full
> > >> 1000baseT/Full
> > >> Advertised EEE link modes: 100baseT/Full
> > >> 1000baseT/Full
> > >> Link partner advertised EEE link modes: 100baseT/Full
> > >> 1000baseT/Full
> > >>
> > >>> These are all the tg3 changes between 4.19 and 5.0:
> > >>>
> > >>> 750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
> > >>> cddaf02bcb73 tg3: optionally use eth_platform_get_mac_address() to get
> > >>> mac address
> > >>> 3c1bcc8614db net: ethernet: Convert phydev advertize and supported
> > >>> from u32 to link mode
> > >>> 6fe42e228dc2 tg3: extend PTP gettime function to read system clock
> > >>> 310fc0513ea9 tg3: Fix fall-through annotations
> > >>> 22b7d29926b5 net: ethernet: Add helper to determine if pause
> > >>> configuration is supported
> > >>> 70814e819c11 net: ethernet: Add helper for set_pauseparam for Asym Pause
> > >>> af8d9bb2f2f4 net: ethernet: Add helper for MACs which support asym pause
> > >>> 04b7d41d8046 net: ethernet: Fix up drivers masking pause support
> > >>> 58056c1e1b0e net: ethernet: Use phy_set_max_speed() to limit advertised speed
> > >>>
> > >>> Most of the changes are related to PHY settings. I suggest that you
> > >>> check the link settings, including speed, pause, asym pause, etc
> > >>> between the working kernel and the non-working kernel to see if there
> > >>> are differences in the settings.
> > >>
> > >
> >
Powered by blists - more mailing lists