| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20200704124507.3336497-3-olteanv@gmail.com>
Date: Sat, 4 Jul 2020 15:45:03 +0300
From: Vladimir Oltean <olteanv@...il.com>
To: davem@...emloft.net, netdev@...r.kernel.org
Cc: andrew@...n.ch, f.fainelli@...il.com, vivien.didelot@...il.com,
claudiu.manoil@....com, alexandru.marginean@....com,
ioana.ciornei@....com, linux@...linux.org.uk
Subject: [PATCH v2 net-next 2/6] net: dsa: felix: support half-duplex link modes
From: Vladimir Oltean <vladimir.oltean@....com>
Ping tested:
[ 11.808455] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.816497] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[root@...028ARDB ~] # ethtool -s swp0 advertise 0x4
[ 18.844591] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 22.048337] mscc_felix 0000:00:00.5 swp0: Link is Up - 100Mbps/Half - flow control off
[root@...028ARDB ~] # ip addr add 192.168.1.1/24 dev swp0
[root@...028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.383/0.611/1.051 ms
[root@...028ARDB ~] # ethtool -s swp0 advertise 0x10
[ 355.637747] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 358.788034] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Half - flow control off
[root@...028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C
--- 192.168.1.2 ping statistics ---
16 packets transmitted, 16 packets received, 0% packet loss
round-trip min/avg/max = 0.301/0.384/1.138 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@....com>
Reviewed-by: Florian Fainelli <f.fainelli@...il.com>
Reviewed-by: Russell King <rmk+kernel@...linux.org.uk>
---
Changes in v2:
None.
Note: this patch is still using state->duplex from mac_config(),
although that will be changed in 6/6.
drivers/net/dsa/ocelot/felix.c | 4 +++-
drivers/net/dsa/ocelot/felix_vsc9959.c | 23 +++++++++++++----------
include/linux/fsl/enetc_mdio.h | 1 +
3 files changed, 17 insertions(+), 11 deletions(-)
diff --git a/drivers/net/dsa/ocelot/felix.c b/drivers/net/dsa/ocelot/felix.c
index 75020af7f7a4..f54648dff0ec 100644
--- a/drivers/net/dsa/ocelot/felix.c
+++ b/drivers/net/dsa/ocelot/felix.c
@@ -194,13 +194,15 @@ static void felix_phylink_validate(struct dsa_switch *ds, int port,
return;
}
- /* No half-duplex. */
phylink_set_port_modes(mask);
phylink_set(mask, Autoneg);
phylink_set(mask, Pause);
phylink_set(mask, Asym_Pause);
+ phylink_set(mask, 10baseT_Half);
phylink_set(mask, 10baseT_Full);
+ phylink_set(mask, 100baseT_Half);
phylink_set(mask, 100baseT_Full);
+ phylink_set(mask, 1000baseT_Half);
phylink_set(mask, 1000baseT_Full);
if (state->interface == PHY_INTERFACE_MODE_INTERNAL ||
diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c
index 9f4c8343652f..94e946b26f90 100644
--- a/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ b/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -817,12 +817,9 @@ static void vsc9959_pcs_init_sgmii(struct phy_device *pcs,
phy_set_bits(pcs, MII_BMCR, BMCR_ANENABLE);
} else {
+ u16 if_mode = ENETC_PCS_IF_MODE_SGMII_EN;
int speed;
- if (state->duplex == DUPLEX_HALF) {
- phydev_err(pcs, "Half duplex not supported\n");
- return;
- }
switch (state->speed) {
case SPEED_1000:
speed = ENETC_PCS_SPEED_1000;
@@ -841,9 +838,9 @@ static void vsc9959_pcs_init_sgmii(struct phy_device *pcs,
return;
}
- phy_write(pcs, ENETC_PCS_IF_MODE,
- ENETC_PCS_IF_MODE_SGMII_EN |
- ENETC_PCS_IF_MODE_SGMII_SPEED(speed));
+ if_mode |= ENETC_PCS_IF_MODE_SGMII_SPEED(speed);
+ if (state->duplex == DUPLEX_HALF)
+ if_mode |= ENETC_PCS_IF_MODE_DUPLEX_HALF;
phy_clear_bits(pcs, MII_BMCR, BMCR_ANENABLE);
}
@@ -870,15 +867,18 @@ static void vsc9959_pcs_init_2500basex(struct phy_device *pcs,
unsigned int link_an_mode,
const struct phylink_link_state *state)
{
+ u16 if_mode = ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_2500) |
+ ENETC_PCS_IF_MODE_SGMII_EN;
+
if (link_an_mode == MLO_AN_INBAND) {
phydev_err(pcs, "AN not supported on 3.125GHz SerDes lane\n");
return;
}
- phy_write(pcs, ENETC_PCS_IF_MODE,
- ENETC_PCS_IF_MODE_SGMII_EN |
- ENETC_PCS_IF_MODE_SGMII_SPEED(ENETC_PCS_SPEED_2500));
+ if (state->duplex == DUPLEX_HALF)
+ if_mode |= ENETC_PCS_IF_MODE_DUPLEX_HALF;
+ phy_write(pcs, ENETC_PCS_IF_MODE, if_mode);
phy_clear_bits(pcs, MII_BMCR, BMCR_ANENABLE);
}
@@ -919,8 +919,11 @@ static void vsc9959_pcs_init(struct ocelot *ocelot, int port,
linkmode_set_bit_array(phy_basic_ports_array,
ARRAY_SIZE(phy_basic_ports_array),
pcs->supported);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, pcs->supported);
linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, pcs->supported);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, pcs->supported);
linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, pcs->supported);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, pcs->supported);
linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, pcs->supported);
if (pcs->interface == PHY_INTERFACE_MODE_2500BASEX ||
pcs->interface == PHY_INTERFACE_MODE_USXGMII)
diff --git a/include/linux/fsl/enetc_mdio.h b/include/linux/fsl/enetc_mdio.h
index 4875dd38af7e..2d9203314865 100644
--- a/include/linux/fsl/enetc_mdio.h
+++ b/include/linux/fsl/enetc_mdio.h
@@ -15,6 +15,7 @@
#define ENETC_PCS_IF_MODE_SGMII_EN BIT(0)
#define ENETC_PCS_IF_MODE_USE_SGMII_AN BIT(1)
#define ENETC_PCS_IF_MODE_SGMII_SPEED(x) (((x) << 2) & GENMASK(3, 2))
+#define ENETC_PCS_IF_MODE_DUPLEX_HALF BIT(3)
/* Not a mistake, the SerDes PLL needs to be set at 3.125 GHz by Reset
* Configuration Word (RCW, outside Linux control) for 2.5G SGMII mode. The PCS
--
2.25.1
Powered by blists - more mailing lists