| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20210630180146.1121925-2-robert.hancock@calian.com>
Date: Wed, 30 Jun 2021 12:01:45 -0600
From: Robert Hancock <robert.hancock@...ian.com>
To: andrew@...n.ch, hkallweit1@...il.com
Cc: linux@...linux.org.uk, davem@...emloft.net, kuba@...nel.org,
netdev@...r.kernel.org, Robert Hancock <robert.hancock@...ian.com>
Subject: [PATCH net-next 1/2] net: phy: at803x: add fiber support
Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.
Enable the appropriate interrupt bits to detect fiber-side link up
or down events.
Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.
Signed-off-by: Robert Hancock <robert.hancock@...ian.com>
---
drivers/net/phy/at803x.c | 69 ++++++++++++++++++++++++++++++++++------
1 file changed, 59 insertions(+), 10 deletions(-)
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 5d62b85a4024..65f546eca5f4 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -48,6 +48,8 @@
#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
#define AT803X_INTR_ENABLE_WOL BIT(0)
@@ -81,7 +83,17 @@
#define AT803X_DEBUG_DATA 0x1E
#define AT803X_MODE_CFG_MASK 0x0F
-#define AT803X_MODE_CFG_SGMII 0x01
+#define AT803X_MODE_CFG_BASET_RGMII 0x00
+#define AT803X_MODE_CFG_BASET_SGMII 0x01
+#define AT803X_MODE_CFG_BX1000_RGMII_50 0x02
+#define AT803X_MODE_CFG_BX1000_RGMII_75 0x03
+#define AT803X_MODE_CFG_BX1000_CONV_50 0x04
+#define AT803X_MODE_CFG_BX1000_CONV_75 0x05
+#define AT803X_MODE_CFG_FX100_RGMII_50 0x06
+#define AT803X_MODE_CFG_FX100_CONV_50 0x07
+#define AT803X_MODE_CFG_RGMII_AUTO_MDET 0x0B
+#define AT803X_MODE_CFG_FX100_RGMII_75 0x0E
+#define AT803X_MODE_CFG_FX100_CONV_75 0x0F
#define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/
#define AT803X_PSSR_MR_AN_COMPLETE 0x0200
@@ -191,6 +203,8 @@ struct at803x_priv {
u16 clk_25m_mask;
u8 smarteee_lpi_tw_1g;
u8 smarteee_lpi_tw_100m;
+ bool is_fiber;
+ bool is_1000basex;
struct regulator_dev *vddio_rdev;
struct regulator_dev *vddh_rdev;
struct regulator *vddio;
@@ -673,12 +687,32 @@ static int at803x_probe(struct phy_device *phydev)
}
/* Some bootloaders leave the fiber page selected.
- * Switch to the copper page, as otherwise we read
- * the PHY capabilities from the fiber side.
+ * Switch to the appropriate page (fiber or copper), as otherwise we
+ * read the PHY capabilities from the wrong page.
*/
if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+ int mode_cfg;
+
+ ret = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
+ if (ret < 0)
+ goto err;
+ mode_cfg = ret & AT803X_MODE_CFG_MASK;
+
+ switch (mode_cfg) {
+ case AT803X_MODE_CFG_BX1000_RGMII_50:
+ case AT803X_MODE_CFG_BX1000_RGMII_75:
+ priv->is_1000basex = true;
+ fallthrough;
+ case AT803X_MODE_CFG_FX100_RGMII_50:
+ case AT803X_MODE_CFG_FX100_RGMII_75:
+ priv->is_fiber = true;
+ break;
+ }
+
phy_lock_mdio_bus(phydev);
- ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
+ ret = at803x_write_page(phydev,
+ priv->is_fiber ? AT803X_PAGE_FIBER :
+ AT803X_PAGE_COPPER);
phy_unlock_mdio_bus(phydev);
if (ret)
goto err;
@@ -703,6 +737,7 @@ static void at803x_remove(struct phy_device *phydev)
static int at803x_get_features(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int err;
err = genphy_read_abilities(phydev);
@@ -720,12 +755,13 @@ static int at803x_get_features(struct phy_device *phydev)
* As a result of that, ESTATUS_1000_XFULL is set
* to 1 even when operating in copper TP mode.
*
- * Remove this mode from the supported link modes,
- * as this driver currently only supports copper
- * operation.
+ * Remove this mode from the supported link modes
+ * when the device is configured for copper operation.
*/
- linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
- phydev->supported);
+ if (!priv->is_1000basex)
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+ phydev->supported);
+
return 0;
}
@@ -846,6 +882,7 @@ static int at803x_ack_interrupt(struct phy_device *phydev)
static int at803x_config_intr(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int err;
int value;
@@ -862,6 +899,10 @@ static int at803x_config_intr(struct phy_device *phydev)
value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
value |= AT803X_INTR_ENABLE_LINK_FAIL;
value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+ if (priv->is_fiber) {
+ value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
+ value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
+ }
err = phy_write(phydev, AT803X_INTR_ENABLE, value);
} else {
@@ -929,8 +970,12 @@ static void at803x_link_change_notify(struct phy_device *phydev)
static int at803x_read_status(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int ss, err, old_link = phydev->link;
+ if (priv->is_1000basex)
+ return genphy_c37_read_status(phydev);
+
/* Update the link, but return if there was an error */
err = genphy_update_link(phydev);
if (err)
@@ -1029,6 +1074,7 @@ static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
static int at803x_config_aneg(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int ret;
ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
@@ -1045,7 +1091,10 @@ static int at803x_config_aneg(struct phy_device *phydev)
return ret;
}
- return genphy_config_aneg(phydev);
+ if (priv->is_1000basex)
+ return genphy_c37_config_aneg(phydev);
+ else
+ return genphy_config_aneg(phydev);
}
static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
--
2.27.0
Powered by blists - more mailing lists