[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20230928122427.313271-12-christophe.roullier@foss.st.com>
Date: Thu, 28 Sep 2023 14:24:26 +0200
From: Christophe Roullier <christophe.roullier@...s.st.com>
To: "David S . Miller" <davem@...emloft.net>,
Eric Dumazet
<edumazet@...gle.com>, Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni
<pabeni@...hat.com>, Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski
<krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>,
Maxime Coquelin <mcoquelin.stm32@...il.com>,
Alexandre Torgue
<alexandre.torgue@...s.st.com>,
Richard Cochran <richardcochran@...il.com>,
Jose Abreu <joabreu@...opsys.com>, Liam Girdwood <lgirdwood@...il.com>,
Mark
Brown <broonie@...nel.org>,
Christophe Roullier
<christophe.roullier@...s.st.com>
CC: <netdev@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-stm32@...md-mailman.stormreply.com>,
<linux-arm-kernel@...ts.infradead.org>, <linux-kernel@...r.kernel.org>
Subject: [PATCH v2 11/12] ARM: dts: stm32: add ethernet1 and ethernet2 for STM32MP135F-DK board
Add dual Ethernet:
-Ethernet1: RMII with crystal
-Ethernet2: RMII without crystal
PHYs used are SMSC (LAN8742A)
With Ethernet1, we can performed WoL from PHY instead of GMAC point of view.
(in this case IRQ for WoL is managed as wakeup pin and configured
in OS secure).
Signed-off-by: Christophe Roullier <christophe.roullier@...s.st.com>
---
arch/arm/boot/dts/st/stm32mp135f-dk.dts | 48 +++++++++++++++++++++++++
1 file changed, 48 insertions(+)
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
index eea740d097c72..1316cc16f8dd9 100644
--- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts
+++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
@@ -19,6 +19,8 @@ / {
compatible = "st,stm32mp135f-dk", "st,stm32mp135";
aliases {
+ ethernet0 = ðernet1;
+ ethernet1 = ðernet2;
serial0 = &uart4;
serial1 = &usart1;
serial2 = &uart8;
@@ -93,6 +95,52 @@ channel@12 {
};
};
+ðernet1 {
+ status = "okay";
+ pinctrl-0 = <ð1_rmii_pins_a>;
+ pinctrl-1 = <ð1_rmii_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rmii";
+ max-speed = <100>;
+ phy-handle = <&phy0_eth1>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+
+ phy0_eth1: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0007.c131";
+ reset-gpios = <&mcp23017 9 GPIO_ACTIVE_LOW>;
+ reg = <0>;
+ wakeup-source;
+ };
+ };
+};
+
+ðernet2 {
+ status = "okay";
+ pinctrl-0 = <ð2_rmii_pins_a>;
+ pinctrl-1 = <ð2_rmii_sleep_pins_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rmii";
+ max-speed = <100>;
+ phy-handle = <&phy0_eth2>;
+ st,ext-phyclk;
+ phy-supply = <&scmi_v3v3_sw>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0_eth2: ethernet-phy@0 {
+ compatible = "ethernet-phy-id0007.c131";
+ reset-gpios = <&mcp23017 10 GPIO_ACTIVE_LOW>;
+ reg = <0>;
+ };
+ };
+};
+
&i2c1 {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c1_pins_a>;
--
2.25.1
Powered by blists - more mailing lists