netdev - Re: [PATCH] net: phy: marvell-88q2xxx: add driver for the Marvell 88Q2220 PHY

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <20231216221151.GA143483@debian>
Date: Sat, 16 Dec 2023 23:11:51 +0100
From: Dimitri Fedrau <dima.fedrau@...il.com>
To: Andrew Lunn <andrew@...n.ch>
Cc: Heiner Kallweit <hkallweit1@...il.com>,
	Russell King <linux@...linux.org.uk>,
	"David S. Miller" <davem@...emloft.net>,
	Eric Dumazet <edumazet@...gle.com>,
	Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
	Stefan Eichenberger <eichest@...il.com>, netdev@...r.kernel.org,
	linux-kernel@...r.kernel.org
Subject: Re: [PATCH] net: phy: marvell-88q2xxx: add driver for the Marvell
 88Q2220 PHY

Am Sat, Dec 16, 2023 at 05:46:32PM +0100 schrieb Andrew Lunn:
> > +static int mv88q222x_config_aneg_gbit(struct phy_device *phydev)
> > +{
> > +	int ret;
> > +
> > +	/* send_s detection threshold, slave and master */
> > +	ret = phy_write_mmd(phydev, MDIO_MMD_AN, 0x8032, 0x2020);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	ret = phy_write_mmd(phydev, MDIO_MMD_AN, 0x8031, 0xa28);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	ret = phy_write_mmd(phydev, MDIO_MMD_AN, 0x8031, 0xc28);
> > +	if (ret < 0)
> > +		return ret;
> 
> Same register with two different values?
>
Just copied the init sequence from sample code provided by Marvell.
I don't know if its a mistake. There is no documentation on this.

> There are a lot of magic values here. Does the datasheet names these
> registers? Does it define the bits? Adding #defines would be good.
> 
Datasheet is not naming them. I once asked Marvell Support for
documentation on the init sequence and what purpose each register has.
Just got the answer to use the sample code as it is.

> > +static int mv88q222x_config_aneg_preinit(struct phy_device *phydev)
> > +{
> > +	int ret, val, i;
> > +
> > +	/* Enable txdac */
> > +	ret = phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8033, 0x6801);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	/* Disable ANEG */
> > +	ret = phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_CTRL, 0x0);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	/* Set IEEE power down */
> > +	ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1, 0x840);
> 
> 0x800 is MDIO_CTRL1_LPOWER. What is the other? It seems like a speed
> selection bit?
>
The other is MDIO_PMA_CTRL1_SPEED1000. Will fix this in V2.

> 	  Andrew