netdev - Re: [RFC PATCH v2 0/3] Introduce switch mode support for ICSSG driver

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <f3d75103-c1ca-448d-b5aa-736496d00342@lunn.ch>
Date: Thu, 18 Jan 2024 15:01:55 +0100
From: Andrew Lunn <andrew@...n.ch>
To: MD Danish Anwar <danishanwar@...com>
Cc: Rob Herring <robh@...nel.org>, Dan Carpenter <dan.carpenter@...aro.org>,
	Jan Kiszka <jan.kiszka@...mens.com>,
	Vladimir Oltean <vladimir.oltean@....com>,
	Wolfram Sang <wsa+renesas@...g-engineering.com>,
	Arnd Bergmann <arnd@...db.de>,
	Grygorii Strashko <grygorii.strashko@...com>,
	Vignesh Raghavendra <vigneshr@...com>,
	Roger Quadros <rogerq@...nel.org>, Paolo Abeni <pabeni@...hat.com>,
	Jakub Kicinski <kuba@...nel.org>,
	Eric Dumazet <edumazet@...gle.com>,
	"David S. Miller" <davem@...emloft.net>,
	linux-arm-kernel@...ts.infradead.org, netdev@...r.kernel.org,
	linux-kernel@...r.kernel.org, srk@...com, r-gunasekaran@...com
Subject: Re: [RFC PATCH v2 0/3] Introduce switch mode support for ICSSG driver

On Thu, Jan 18, 2024 at 12:40:02PM +0530, MD Danish Anwar wrote:
> This series adds support for switch-mode for ICSSG driver. This series
> also introduces helper APIs to configure firmware maintained FDB
> (Forwarding Database) and VLAN tables. These APIs are later used by ICSSG
> driver in switch mode.
> 
> Now the driver will boot by default in dual EMAC mode. When first ICSSG
> interface is added to bridge driver will still be in EMAC mode. As soon as
> second ICSSG interface is added to same bridge, switch-mode will be
> enabled and switch firmwares will be loaded to PRU cores. The driver will
> remain in dual EMAC mode if ICSSG interfaces are added to two different
> bridges or if two differnet interfaces (One ICSSG, one other) is added to
> the same bridge. We'll only enable is_switch_mode flag when two ICSSG
> interfaces are added to same bridge.
> 
> We start in dual MAC mode. Let's say lan0 and lan1 are ICSSG interfaces
> 
> ip link add name br0 type bridge
> ip link set lan0 master br0
> 
> At this point, we get a CHANGEUPPER event. Only one port is a member of
> the bridge, so we will still be in dual MAC mode.
> 
> ip link set lan1 master br0
> 
> We get a second CHANGEUPPER event, the secind interface lan1 is also ICSSG
> interface so we will set the is_switch_mode flag and when interfaces are
> brought up again, ICSSG switch firmwares will be loaded to PRU Cores.
> 
> There are some other cases to consider as well. 
> 
> ip link add name br0 type bridge
> ip link add name br1 type bridge
> 
> ip link set lan0 master br0
> ip link set ppp0 master br0
> 
> Here we are adding lan0 (ICSSG) and ppp0 (non ICSSG) to same bridge, as
> they both are not ICSSG, we will still be running in dual EMAC mode.
> 
> ip link set lan1 master br1
> ip link set vpn0 master br1
> 
> Here we are adding lan1 (ICSSG) and vpn0 (non ICSSG) to same bridge, as
> they both are not ICSSG, we will still be running in dual EMAC mode.

This is going in the right direction, thanks for the changes.

What features does the dual EMAC firmware support which the switch
firmware does not?

If such features are in use, you should not reload firmware to the
switch firmware, since it will break whatever has been
configured. Keep with bridging in software.

Similarly, what features are supported by both firmwares? Does feature
configuration survive a firmware reload? Or is it necessary to pass
all the configuration to the firmware again?

    Andrew