netdev - Re: [net-next,PATCH 2/2] net: stmmac: dwmac-stm32: stm32: add management of stm32mp25 for stm32

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Date: Wed, 19 Jun 2024 20:56:40 +0200
From: Marek Vasut <marex@...x.de>
To: Christophe ROULLIER <christophe.roullier@...s.st.com>,
 "David S . Miller" <davem@...emloft.net>, Eric Dumazet
 <edumazet@...gle.com>, Jakub Kicinski <kuba@...nel.org>,
 Paolo Abeni <pabeni@...hat.com>, Rob Herring <robh+dt@...nel.org>,
 Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
 Conor Dooley <conor+dt@...nel.org>,
 Maxime Coquelin <mcoquelin.stm32@...il.com>,
 Alexandre Torgue <alexandre.torgue@...s.st.com>,
 Richard Cochran <richardcochran@...il.com>, Jose Abreu
 <joabreu@...opsys.com>, Liam Girdwood <lgirdwood@...il.com>,
 Mark Brown <broonie@...nel.org>
Cc: netdev@...r.kernel.org, devicetree@...r.kernel.org,
 linux-stm32@...md-mailman.stormreply.com,
 linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [net-next,PATCH 2/2] net: stmmac: dwmac-stm32: stm32: add
 management of stm32mp25 for stm32

On 6/19/24 5:40 PM, Christophe ROULLIER wrote:
> 
> On 6/19/24 15:14, Marek Vasut wrote:
>> On 6/19/24 9:41 AM, Christophe ROULLIER wrote:
>>
>> Hi,
>>
>>>>>>>>> +static int stm32mp2_configure_syscfg(struct 
>>>>>>>>> plat_stmmacenet_data *plat_dat)
>>>>>>>>> +{
>>>>>>>>> +    struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
>>>>>>>>> +    u32 reg = dwmac->mode_reg;
>>>>>>>>> +    int val = 0;
>>>>>>>>> +
>>>>>>>>> +    switch (plat_dat->mac_interface) {
>>>>>>>>> +    case PHY_INTERFACE_MODE_MII:
>>>>>>>>> +        break;
>>>>>>>>
>>>>>>>> dwmac->enable_eth_ck does not apply to MII mode ? Why ?
>>>>>>>
>>>>>>> It is like MP1 and MP13, nothing to set in syscfg register for 
>>>>>>> case MII mode wo crystal.
>>>>>>
>>>>>> Have a look at STM32MP15xx RM0436 Figure 83. Peripheral clock 
>>>>>> distribution for Ethernet.
>>>>>>
>>>>>> If RCC (top-left corner of the figure) generates 25 MHz MII clock 
>>>>>> (yellow line) on eth_clk_fb (top-right corner), can I set 
>>>>>> ETH_REF_CLK_SEL to position '1' and ETH_SEL[2] to '0' and feed ETH 
>>>>>> (right side) clk_rx_i input with 25 MHz clock that way ?
>>>>>>
>>>>>> I seems like this should be possible, at least theoretically. Can 
>>>>>> you check with the hardware/silicon people ?
>>>>> No it is not possible (it will work if speed (and frequency) is 
>>>>> fixed 25Mhz=100Mbps, but for speed 10Mbps (2,5MHz) it will not work.
>>>>
>>>> Could the pll4_p_ck or pll3_q_ck generate either 25 MHz or 2.5 MHz 
>>>> as needed in that case ? Then it would work, right ?
>>>
>>> Yes you can set frequency you want for pll4 or pll3, if you set 25MHz 
>>> and auto-negotiation of speed is 100Mbps it should work (pad ETH_CK 
>>> of 25MHz clock the PHY and eth_clk_fb set to 25MHz for clk_RX)
>>>
>>> but if autoneg of speed is 10Mbps, then 2.5MHz is needed for clk_RX 
>>> (you will provide 25Mhz)
>>
>> What if:
>>
>> - Aneg is 10 Mbps
>> - PLL4_P_CK/PLL3_Q_CK = 2.5 MHz
>> - ETH_REF_CLK_SEL = 1
>> - ETH_SEL[2] = 0
>>
>> ?
>>
>> Then, clk_rx_i is 2.5 MHz, right ?
> Yes that right
>>
>> Does this configuration work ?
> For me no, because PHY Ethernet Oscillator/cristal need in PAD 25Mhz or 
> 50Mhz, I think it is does not work if oscillator frequency provided is 
> 2.5MHz (To my knowledge there is no Ethernet PHY which have oscillator 
> working to 2.5MHz)

Would it work if the PHY had a dedicated Xtal , while the clocking of 
the MAC was done using RCC ?