| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <550AE11D.30207@ti.com>
Date: Thu, 19 Mar 2015 16:45:49 +0200
From: Roger Quadros <rogerq@...com>
To: George Cherian <gcherianv@...il.com>,
Robert Baldyga <r.baldyga@...sung.com>
CC: <balbi@...com>, <gregkh@...uxfoundation.org>,
<myungjoo.ham@...sung.com>, <cw00.choi@...sung.com>,
<linux-usb@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
Marek Szyprowski <m.szyprowski@...sung.com>,
Łukasz Stelmach <l.stelmach@...sung.com>
Subject: Re: [RFC 01/19] extcon: add extcon-odroid-usbotg driver
On 19/03/15 14:19, George Cherian wrote:
> Hi Robert,
>
> +Roger
> On Thu, Mar 19, 2015 at 5:37 PM, Robert Baldyga <r.baldyga@...sung.com> wrote:
>> Hi George,
>>
>> On 03/19/2015 09:50 AM, George Cherian wrote:
>>> Hi Robert,
>>>
>>> This looks like a extcon driver based on gpio for USB.
>>>
>>> Roger posted a generic one a while back.
>>> https://lkml.org/lkml/2015/2/2/187
>>>
>>> Doesn't this serve the purpose rather than adding this driver?
>>
>> Roger's driver doesn't support VBUS state detection so it cannot handle
> I feel Roger's driver could be extended for supporting VBUS.
> Also I think Roger's driver is about to get merged.
> Probably, Roger or Chanwoo can better tell that
It is already queued for 4.1 and is available in linux-next.
>
>> situation when USB cable is unpluged. In addition some of Odroid boards
>> has only VBUS detection (without ID pin), so this driver cannot handle
>> them at all.
why not?
x15-beagleboard also gets VBUS event over GPIO and I was planning to extent it
to support VBUS detection.
cheers,
-roger
>>
>> Best regards,
>> Robert
>>
>>>
>>> On Wed, Mar 18, 2015 at 7:34 PM, Robert Baldyga <r.baldyga@...sung.com> wrote:
>>>> This patch adds extcon driver for Odroid U3, U3+ and X boards.
>>>> It recognizes type of USB cable connected to Odroid board basing on
>>>> two signal lines VBUS_DET and OTG_ID (the second one is present only
>>>> on Odroid U3+ board).
>>>>
>>>> Following table of states presents relationship between this signals
>>>> and detected cable type:
>>>>
>>>> state | VBUS_DET | OTG_ID
>>>> -------------------------------
>>>> USB | H | H
>>>> USB_HOST | H | L
>>>> disconn. | L | H
>>>> USB-HOST | L | L
>>>>
>>>> This driver is based on extcon-gpio driver.
>>>>
>>>> Signed-off-by: Łukasz Stelmach <l.stelmach@...sung.com>
>>>> Signed-off-by: Robert Baldyga <r.baldyga@...sung.com>
>>>> ---
>>>> drivers/extcon/Kconfig | 4 +
>>>> drivers/extcon/Makefile | 1 +
>>>> drivers/extcon/extcon-odroid-usbotg.c | 256 ++++++++++++++++++++++++++++++++++
>>>> 3 files changed, 261 insertions(+)
>>>> create mode 100644 drivers/extcon/extcon-odroid-usbotg.c
>>>>
>>>> diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
>>>> index 6a1f7de..891dca3 100644
>>>> --- a/drivers/extcon/Kconfig
>>>> +++ b/drivers/extcon/Kconfig
>>>> @@ -93,4 +93,8 @@ config EXTCON_SM5502
>>>> Silicon Mitus SM5502. The SM5502 is a USB port accessory
>>>> detector and switch.
>>>>
>>>> +config EXTCON_ODROID_USBOTG
>>>> + tristate "Extcon Odroid U3, U3+, X and XU USB OTG port"
>>>> + depends on OF_GPIO
>>>> +
>>>> endif # MULTISTATE_SWITCH
>>>> diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
>>>> index 0370b42..514384e 100644
>>>> --- a/drivers/extcon/Makefile
>>>> +++ b/drivers/extcon/Makefile
>>>> @@ -12,3 +12,4 @@ obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o
>>>> obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o
>>>> obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o
>>>> obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o
>>>> +obj-$(CONFIG_EXTCON_ODROID_USBOTG) += extcon-odroid-usbotg.o
>>>> diff --git a/drivers/extcon/extcon-odroid-usbotg.c b/drivers/extcon/extcon-odroid-usbotg.c
>>>> new file mode 100644
>>>> index 0000000..7f71c48
>>>> --- /dev/null
>>>> +++ b/drivers/extcon/extcon-odroid-usbotg.c
>>>> @@ -0,0 +1,256 @@
>>>> +/*
>>>> + * drivers/extcon/extcon-odroid-usbotg.c
>>>> + *
>>>> + * USB cable extcon driver for Odroid U3, Odroid U3+ and Odroid X
>>>> + *
>>>> + * Copyright (C) 2014 Samsung Electronics
>>>> + * Author: Lukasz Stelmach <l.stelmach@...sung.com>
>>>> + * Author: Robert Baldyga <r.baldyga@...sung.com>
>>>> + *
>>>> + * based on drivers/extcon/extcon-gpio.c
>>>> + * Copyright (C) 2008 Google, Inc.
>>>> + * Author: Mike Lockwood <lockwood@...roid.com>
>>>> + *
>>>> + * This software is licensed under the terms of the GNU General Public
>>>> + * License version 2, as published by the Free Software Foundation, and
>>>> + * may be copied, distributed, and modified under those terms.
>>>> + *
>>>> + * This program is distributed in the hope that it will be useful,
>>>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>>>> + * GNU General Public License for more details.
>>>> + *
>>>> + */
>>>> +
>>>> +#include <linux/module.h>
>>>> +#include <linux/kernel.h>
>>>> +#include <linux/init.h>
>>>> +#include <linux/interrupt.h>
>>>> +#include <linux/platform_device.h>
>>>> +#include <linux/slab.h>
>>>> +#include <linux/gpio.h>
>>>> +#include <linux/of_gpio.h>
>>>> +#include <linux/extcon.h>
>>>> +#include <linux/extcon/extcon-gpio.h>
>>>> +#include <linux/delay.h>
>>>> +
>>>> +enum {
>>>> + EXTCON_CABLE_USB = 0,
>>>> + EXTCON_CABLE_USB_HOST,
>>>> +
>>>> + _EXTCON_CABLE_NUM,
>>>> +};
>>>> +
>>>> +static const char * const odroid_usbotg_cable[] = {
>>>> + [EXTCON_CABLE_USB] = "USB",
>>>> + [EXTCON_CABLE_USB_HOST] = "USB-HOST",
>>>> +
>>>> + NULL,
>>>> +};
>>>> +
>>>> +struct odroid_usbotg_data {
>>>> + struct extcon_dev *edev;
>>>> + struct gpio_desc *otg_id;
>>>> + struct gpio_desc *vbus_det;
>>>> + int otg_id_irq;
>>>> + int vbus_det_irq;
>>>> + unsigned long debounce_ms;
>>>> +};
>>>> +
>>>> +/*
>>>> + * state | VBUS_DET | OTG_ID
>>>> + * -------------------------------
>>>> + * USB | H | H
>>>> + * USB-HOST | H | L
>>>> + * disconn. | L | H
>>>> + * USB-HOST | L | L
>>>> + *
>>>> + * Only Odroid U3+ has OTG_ID line. U3 and X versions can detect only
>>>> + * USB slave cable.
>>>> + */
>>>> +
>>>> +static void odroid_usbotg_detect_cable(struct odroid_usbotg_data *extcon_data)
>>>> +{
>>>> + int state;
>>>> +
>>>> + mdelay(extcon_data->debounce_ms);
>>>> +
>>>> + if (extcon_data->otg_id)
>>>> + state = (gpiod_get_value(extcon_data->vbus_det) << 1) |
>>>> + gpiod_get_value(extcon_data->otg_id);
>>>> + else
>>>> + state = (gpiod_get_value(extcon_data->vbus_det) << 1) | 1;
>>>> +
>>>> + dev_dbg(&extcon_data->edev->dev, "cable state changed to %d\n", state);
>>>> +
>>>> + if (state & 0x1)
>>>> + extcon_set_cable_state_(extcon_data->edev,
>>>> + EXTCON_CABLE_USB_HOST, false);
>>>> + if (state != 0x3)
>>>> + extcon_set_cable_state_(extcon_data->edev,
>>>> + EXTCON_CABLE_USB, false);
>>>> +
>>>> + if (!(state & 0x1))
>>>> + extcon_set_cable_state_(extcon_data->edev,
>>>> + EXTCON_CABLE_USB_HOST, true);
>>>> + else if (state == 0x3)
>>>> + extcon_set_cable_state_(extcon_data->edev,
>>>> + EXTCON_CABLE_USB, true);
>>>> +}
>>>> +
>>>> +static irqreturn_t gpio_irq_handler(int irq, void *dev_id)
>>>> +{
>>>> + struct odroid_usbotg_data *extcon_data = dev_id;
>>>> +
>>>> + odroid_usbotg_detect_cable(extcon_data);
>>>> +
>>>> + return IRQ_HANDLED;
>>>> +}
>>>> +
>>>> +static int odroid_usbotg_parse_dt(struct platform_device *pdev,
>>>> + struct odroid_usbotg_data *extcon_data)
>>>> +{
>>>> + struct device_node *np = pdev->dev.of_node;
>>>> + u32 val;
>>>> +
>>>> + if (!np)
>>>> + return -ENODEV;
>>>> +
>>>> + extcon_data->edev->name = np->name;
>>>> +
>>>> + if (of_property_read_u32(np, "debounce", &val) != 0)
>>>> + val = 50;
>>>> + extcon_data->debounce_ms = val;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int odroid_usbotg_probe(struct platform_device *pdev)
>>>> +{
>>>> + struct odroid_usbotg_data *extcon_data;
>>>> + int ret = 0;
>>>> +
>>>> + extcon_data = devm_kzalloc(&pdev->dev,
>>>> + sizeof(struct odroid_usbotg_data), GFP_KERNEL);
>>>> + if (!extcon_data)
>>>> + return -ENOMEM;
>>>> +
>>>> + extcon_data->edev = devm_kzalloc(&pdev->dev, sizeof(struct extcon_dev),
>>>> + GFP_KERNEL);
>>>> + if (IS_ERR(extcon_data->edev)) {
>>>> + dev_err(&pdev->dev, "failed to allocate extcon device\n");
>>>> + return -ENOMEM;
>>>> + }
>>>> + extcon_data->edev->supported_cable = odroid_usbotg_cable;
>>>> +
>>>> + ret = odroid_usbotg_parse_dt(pdev, extcon_data);
>>>> + if (IS_ERR_VALUE(ret)) {
>>>> + dev_err(&pdev->dev, "failed to get data from device tree\n");
>>>> + return ret;
>>>> + }
>>>> +
>>>> + /* gpios */
>>>> + extcon_data->vbus_det = devm_gpiod_get(&pdev->dev, "vbus-det");
>>>> + if (IS_ERR(extcon_data->vbus_det)) {
>>>> + dev_err(&pdev->dev, "failed to get vbus_det gpio\n");
>>>> + return PTR_ERR(extcon_data->vbus_det);
>>>> + }
>>>> + extcon_data->otg_id = devm_gpiod_get_optional(&pdev->dev, "otg-id");
>>>> +
>>>> + extcon_data->edev->dev.parent = &pdev->dev;
>>>> + ret = extcon_dev_register(extcon_data->edev);
>>>> + if (ret < 0)
>>>> + return ret;
>>>> +
>>>> + /* irq */
>>>> + extcon_data->vbus_det_irq = gpiod_to_irq(extcon_data->vbus_det);
>>>> + if (extcon_data->vbus_det_irq < 0) {
>>>> + dev_err(&pdev->dev, "failed to get irq from vbus_det\n");
>>>> + ret = extcon_data->vbus_det_irq;
>>>> + goto err;
>>>> + }
>>>> + ret = request_threaded_irq(extcon_data->vbus_det_irq, NULL,
>>>> + gpio_irq_handler, IRQF_ONESHOT |
>>>> + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
>>>> + pdev->name, extcon_data);
>>>> + if (ret < 0) {
>>>> + dev_err(&pdev->dev, "failed to request vbus_det irq\n");
>>>> + goto err;
>>>> + }
>>>> +
>>>> + if (extcon_data->otg_id) {
>>>> + extcon_data->otg_id_irq = gpiod_to_irq(extcon_data->otg_id);
>>>> + if (extcon_data->otg_id_irq < 0) {
>>>> + dev_err(&pdev->dev, "failed to get irq from otg_id\n");
>>>> + ret = extcon_data->otg_id_irq;
>>>> + goto err;
>>>> + }
>>>> + ret = request_threaded_irq(extcon_data->otg_id_irq, NULL,
>>>> + gpio_irq_handler, IRQF_ONESHOT |
>>>> + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
>>>> + pdev->name, extcon_data);
>>>> + if (ret < 0) {
>>>> + dev_err(&pdev->dev, "failed to request otg_id irq\n");
>>>> + goto err;
>>>> + }
>>>> + }
>>>> +
>>>> + platform_set_drvdata(pdev, extcon_data);
>>>> + /* Perform initial detection */
>>>> + odroid_usbotg_detect_cable(extcon_data);
>>>> +
>>>> + dev_dbg(&pdev->dev, "probe: success\n");
>>>> +
>>>> + return 0;
>>>> +
>>>> +err:
>>>> + extcon_dev_unregister(extcon_data->edev);
>>>> +
>>>> + return ret;
>>>> +}
>>>> +
>>>> +static int odroid_usbotg_remove(struct platform_device *pdev)
>>>> +{
>>>> + struct odroid_usbotg_data *extcon_data = platform_get_drvdata(pdev);
>>>> +
>>>> + free_irq(extcon_data->vbus_det_irq, extcon_data);
>>>> + if (extcon_data->otg_id)
>>>> + free_irq(extcon_data->otg_id_irq, extcon_data);
>>>> + extcon_dev_unregister(extcon_data->edev);
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static const struct of_device_id odroid_usbotg_of_match[] = {
>>>> + { .compatible = "extcon-odroid-usbotg" },
>>>> + { },
>>>> +};
>>>> +MODULE_DEVICE_TABLE(of, odroid_usbotg_of_match);
>>>> +
>>>> +static struct platform_driver odroid_usbotg_driver = {
>>>> + .probe = odroid_usbotg_probe,
>>>> + .remove = odroid_usbotg_remove,
>>>> + .driver = {
>>>> + .name = "odroid-usbotg",
>>>> + .owner = THIS_MODULE,
>>>> + .of_match_table = of_match_ptr(odroid_usbotg_of_match)
>>>> + },
>>>> +};
>>>> +
>>>> +static int __init odroid_usbotg_init(void)
>>>> +{
>>>> + return platform_driver_register(&odroid_usbotg_driver);
>>>> +}
>>>> +
>>>> +subsys_initcall(odroid_usbotg_init);
>>>> +
>>>> +static void __exit odroid_usbotg_cleanup(void)
>>>> +{
>>>> + platform_driver_unregister(&odroid_usbotg_driver);
>>>> +}
>>>> +
>>>> +module_exit(odroid_usbotg_cleanup);
>>>> +
>>>> +MODULE_AUTHOR("Lukasz Stelmach <l.stelmach@...sung.com>, Robert Baldyga <r.baldyga@...sung.com>");
>>>> +MODULE_DESCRIPTION("USB OTG extcon driver for Odroid U3, U3+ and X");
>>>> +MODULE_LICENSE("GPL");
>>>> --
>>>> 1.9.1
>>>>
>>>> --
>>>> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
>>>> the body of a message to majordomo@...r.kernel.org
>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
>>> the body of a message to majordomo@...r.kernel.org
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>
>>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
> the body of a message to majordomo@...r.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists