[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <57483582.2080307@osg.samsung.com>
Date: Fri, 27 May 2016 12:54:42 +0100
From: Luis de Bethencourt <luisbg@....samsung.com>
To: Daeseok Youn <daeseok.youn@...il.com>, lidza.louina@...il.com
CC: devel@...verdev.osuosl.org, gregkh@...uxfoundation.org,
driverdev-devel@...uxdriverproject.org,
kernel-janitors@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH 2/7] staging: dgnc: remove unused variable 'intr_modem'
On 27/05/16 07:53, Daeseok Youn wrote:
> The 'intr_modem' variable was used only for increasing.
> So the 'intr_modem' variable is not useful for this driver.
>
> Signed-off-by: Daeseok Youn <daeseok.youn@...il.com>
> ---
> drivers/staging/dgnc/dgnc_cls.c | 1 -
> drivers/staging/dgnc/dgnc_driver.h | 1 -
> drivers/staging/dgnc/dgnc_neo.c | 1 -
> 3 files changed, 3 deletions(-)
>
> diff --git a/drivers/staging/dgnc/dgnc_cls.c b/drivers/staging/dgnc/dgnc_cls.c
> index dcb808f..8cb7361 100644
> --- a/drivers/staging/dgnc/dgnc_cls.c
> +++ b/drivers/staging/dgnc/dgnc_cls.c
> @@ -406,7 +406,6 @@ static inline void cls_parse_isr(struct dgnc_board *brd, uint port)
>
> /* CTS/RTS change of state */
> if (isr & UART_IIR_CTSRTS) {
> - brd->intr_modem++;
> ch->ch_intr_modem++;
> /*
> * Don't need to do anything, the cls_parse_modem
> diff --git a/drivers/staging/dgnc/dgnc_driver.h b/drivers/staging/dgnc/dgnc_driver.h
> index 7ac33ed..2caeff7 100644
> --- a/drivers/staging/dgnc/dgnc_driver.h
> +++ b/drivers/staging/dgnc/dgnc_driver.h
> @@ -183,7 +183,6 @@ struct dgnc_board {
> uint nasync; /* Number of ports on card */
>
> uint irq; /* Interrupt request number */
> - ulong intr_modem; /* Count of interrupts */
> ulong intr_tx; /* Count of interrupts */
> ulong intr_rx; /* Count of interrupts */
>
> diff --git a/drivers/staging/dgnc/dgnc_neo.c b/drivers/staging/dgnc/dgnc_neo.c
> index 3f8bbb3..a3e100b 100644
> --- a/drivers/staging/dgnc/dgnc_neo.c
> +++ b/drivers/staging/dgnc/dgnc_neo.c
> @@ -452,7 +452,6 @@ static inline void neo_parse_isr(struct dgnc_board *brd, uint port)
> * If we get here, this means the hardware is doing auto flow control.
> * Check to see whether RTS/DTR or CTS/DSR caused this interrupt.
> */
> - brd->intr_modem++;
> ch->ch_intr_modem++;
> cause = readb(&ch->ch_neo_uart->mcr);
> /* Which pin is doing auto flow? RTS or DTR? */
>
Looks good.
Luis
Powered by blists - more mailing lists