linux-kernel - Re: [PATCH 2/2] gpio: mt7621: pass mediatek_gpio_bank_probe() failure up the stack

Open Source and information security mailing list archives

Message-ID: <20181127080113.GA2426@osadl.at>
Date:   Tue, 27 Nov 2018 09:01:13 +0100
From:   Nicholas Mc Guire <der.herr@...r.at>
To:     Sean Wang <sean.wang@...nel.org>
Cc:     hofrat@...dl.org, Linus Walleij <linus.walleij@...aro.org>,
        sergio.paracuellos@...il.com, linux-gpio@...r.kernel.org,
        linux-kernel@...r.kernel.org, bgolaszewski@...libre.com,
        linux-mediatek@...ts.infradead.org,
        Matthias Brugger <matthias.bgg@...il.com>,
        linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH 2/2] gpio: mt7621: pass mediatek_gpio_bank_probe()
 failure up the stack

On Mon, Nov 26, 2018 at 11:49:26PM -0800, Sean Wang wrote:
> Nicholas Mc Guire <hofrat@...dl.org> ??? 2018???11???21??? ?????? ??????10:13?????????
> >
> > The error cases of mediatek_gpio_bank_probe() would go unnoticed (except
> > for the dev_err() messages). The probe function should return an error
> > if one of the banks failed to initialize properly.
> >
> > Signed-off-by: Nicholas Mc Guire <hofrat@...dl.org>
> > Fixes: 4ba9c3afda41 ("gpio: mt7621: Add a driver for MT7621")
> > ---
> >
> > Patch was compile tested with: omega2p_defconfig, SOC_MT7621=y,
> > GPIOLIB=y, GPIO_MT7621=y
> >
> > Patch is against 4.20-rc3 (localversion-next is next-20181121)
> >
> >  drivers/gpio/gpio-mt7621.c | 8 ++++++--
> >  1 file changed, 6 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/gpio/gpio-mt7621.c b/drivers/gpio/gpio-mt7621.c
> > index 1ec95bc..68fca8b 100644
> > --- a/drivers/gpio/gpio-mt7621.c
> > +++ b/drivers/gpio/gpio-mt7621.c
> > @@ -297,6 +297,7 @@ mediatek_gpio_probe(struct platform_device *pdev)
> >         struct device_node *np = dev->of_node;
> >         struct mtk *mtk;
> >         int i;
> > +       int ret;
> >
> >         mtk = devm_kzalloc(dev, sizeof(*mtk), GFP_KERNEL);
> >         if (!mtk)
> > @@ -311,8 +312,11 @@ mediatek_gpio_probe(struct platform_device *pdev)
> >         platform_set_drvdata(pdev, mtk);
> >         mediatek_gpio_irq_chip.name = dev_name(dev);
> >
> > -       for (i = 0; i < MTK_BANK_CNT; i++)
> > -               mediatek_gpio_bank_probe(dev, np, i);
> > +       for (i = 0; i < MTK_BANK_CNT; i++) {
> > +               ret = mediatek_gpio_bank_probe(dev, np, i);
> > +               if (!ret)
> 
> it should be if (ret < 0) ?

I don´t think so mediatek_gpio_bank_probe() returns 0 on success
and all other returns are error paths - while the current code
only returns negative values I do thik that any non 0 would be
an error indication so !ret should be fine here.

thx!
hofrat

> 
> > +                       return ret;
> > +       }
> >
> >         return 0;
> >  }
> > --
> > 2.1.4
> >
> >
> > _______________________________________________
> > Linux-mediatek mailing list
> > Linux-mediatek@...ts.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-mediatek

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives