| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <baef6ba37a7a8d6e4dec0cfbc4ab8252b1d7a3fa.camel@nxp.com>
Date: Fri, 12 Apr 2019 14:39:28 +0000
From: Leonard Crestez <leonard.crestez@....com>
To: "matti.vaittinen@...rohmeurope.com"
<matti.vaittinen@...rohmeurope.com>,
"angus@...ea.ca" <angus@...ea.ca>
CC: dl-linux-imx <linux-imx@....com>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
"robh+dt@...nel.org" <robh+dt@...nel.org>,
"devicetree@...r.kernel.org" <devicetree@...r.kernel.org>,
"festevam@...il.com" <festevam@...il.com>,
"mark.rutland@....com" <mark.rutland@....com>,
"shawnguo@...nel.org" <shawnguo@...nel.org>,
"linux-arm-kernel@...ts.infradead.org"
<linux-arm-kernel@...ts.infradead.org>,
Robin Gong <yibin.gong@....com>,
"kernel@...gutronix.de" <kernel@...gutronix.de>,
"s.hauer@...gutronix.de" <s.hauer@...gutronix.de>
Subject: Re: [PATCH v2 1/2] arm64: dts: fsl: librem5: Add a device tree for
the Librem5 devkit
On Fri, 2019-04-12 at 07:04 -0600, Angus Ainslie (Purism) wrote:
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic: pmic@4b {
> + reg = <0x4b>;
> + compatible = "rohm,bd71837";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + clocks = <&pmic_osc>;
> + clock-names = "osc";
> + clock-output-names = "pmic_clk";
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 GPIO_ACTIVE_LOW>;
> + interrupt-names = "irq";
> + rohm,reset-snvs-powered;
> +
> + gpo {
> + /* 0b0000_1100 all gpos with cmos output mode
> */
> + rohm,drv = <0x0C>;
> + };
After searching for this gpo/rohm,drv property it does not seem to be
documented or handled anywhere?
Should probably just drop.
> + regulators {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + buck1_reg: BUCK1@0 {
> + reg = <0>;
> + regulator-name = "buck1";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <1250>;
> + rohm,dvs-run-voltage = <900000>;
> + rohm,dvs-idle-voltage = <850000>;
> + rohm,dvs-suspend-voltage = <800000>;
> + };
> +
> + buck2_reg: BUCK2@1 {
> + reg = <1>;
> + regulator-name = "buck2";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <1250>;
> + rohm,dvs-run-voltage = <1000000>;
> + rohm,dvs-idle-voltage = <900000>;
> + };
> +
> + buck3_reg: BUCK3@2 {
> + reg = <2>;
> + regulator-name = "buck3";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + rohm,dvs-run-voltage = <1000000>;
> + };
> +
> + buck4_reg: BUCK4@3 {
> + reg = <3>;
> + regulator-name = "buck4";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1300000>;
> + rohm,dvs-run-voltage = <1000000>;
> + };
> +
> + buck5_reg: BUCK5@4 {
> + reg = <4>;
> + regulator-name = "buck5";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6_reg: BUCK6@5 {
> + reg = <5>;
> + regulator-name = "buck6";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck7_reg: BUCK7@6 {
> + reg = <6>;
> + regulator-name = "buck7";
> + regulator-min-microvolt = <1605000>;
> + regulator-max-microvolt = <1995000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck8_reg: BUCK8@7 {
> + reg = <7>;
> + regulator-name = "buck8";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1_reg: LDO1@8 {
> + reg = <8>;
> + regulator-name = "ldo1";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo2_reg: LDO2@9 {
> + reg = <9>;
> + regulator-name = "ldo2";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3_reg: LDO3@10 {
> + reg = <10>;
> + regulator-name = "ldo3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4_reg: LDO4@11 {
> + reg = <11>;
> + regulator-name = "ldo4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5_reg: LDO5@12 {
> + reg = <12>;
> + regulator-name = "ldo5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + ldo6_reg: LDO6@13 {
> + reg = <13>;
> + regulator-name = "ldo6";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + ldo7_reg: LDO7@14 {
> + reg = <14>;
> + regulator-name = "ldo7";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> + };
> + };
Powered by blists - more mailing lists