Message-ID: <860100a0-0bd7-d584-4177-de6ca82c245c@ti.com>
Date:   Fri, 20 Dec 2019 13:08:30 +0200
From:   Tero Kristo <t-kristo@...com>
To:     Mathieu Poirier <mathieu.poirier@...aro.org>
CC:     <bjorn.andersson@...aro.org>, <ohad@...ery.com>,
        <linux-remoteproc@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <linux-omap@...r.kernel.org>, Suman Anna <s-anna@...com>
Subject: Re: [PATCHv3 13/15] remoteproc/omap: add support for runtime
 auto-suspend/resume

On 20/12/2019 01:43, Mathieu Poirier wrote:
> On Fri, Dec 13, 2019 at 02:55:35PM +0200, Tero Kristo wrote:
>> From: Suman Anna <s-anna@...com>
>>
>> This patch enhances the PM support in the OMAP remoteproc driver to
>> support the runtime auto-suspend. A remoteproc may not be required to
>> be running all the time, and typically will need to be active only
>> during certain usecases. As such, to save power, it should be turned
>> off during potential long periods of inactivity between usecases.
>> This suspend and resume of the device is a relatively heavy process
>> in terms of latencies, so a remoteproc should be suspended only after
>> a certain period of prolonged inactivity. The OMAP remoteproc driver
>> leverages the runtime pm framework's auto_suspend feature to accomplish
>> this functionality. This feature is automatically enabled when a remote
>> processor has successfully booted. The 'autosuspend_delay_ms' for each
>> device dictates the inactivity period/time to wait for before
>> suspending the device.
>>
>> The runtime auto-suspend design relies on marking the last busy time
>> on every communication (virtqueue kick) to and from the remote processor.
>> When there has been no activity for 'autosuspend_delay_ms' time, the
>> runtime PM framework invokes the driver's runtime pm suspend callback
>> to suspend the device. The remote processor will be woken up on the
>> initiation of the next communication message through the runtime pm
>> resume callback. The current auto-suspend design also allows a remote
>> processor to deny a auto-suspend attempt, if it wishes to, by sending a
>> NACK response to the initial suspend request message sent to the remote
>> processor as part of the suspend process. The auto-suspend request is
>> also only attempted if the remote processor is idled and in standby at
>> the time of inactivity timer expiry. This choice is made to avoid
>> unnecessary messaging, and the auto-suspend is simply rescheduled to
>> be attempted again after a further lapse of autosuspend_delay_ms.
>>
>> The runtime pm callbacks functionality in this patch reuses most of the
>> core logic from the suspend/resume support code, and make use of an
>> additional auto_suspend flag to differentiate the logic in common code
>> from system suspend. The system suspend/resume sequences are also updated
>> to reflect the proper pm_runtime statuses, and also to really perform a
>> suspend/resume only if the remoteproc has not been auto-suspended at the
>> time of request. The remote processor is left in suspended state on a
>> system resume if it has been auto-suspended before, and will be woken up
>> only when a usecase needs to run. The other significant change in this
>> patch is to reset the remoteproc device's pm_domain so as to avoid
>> conflicts with the ordering sequences in the device pm_domain's runtime
>> callbacks and the reset management and clock management implemented
>> within the runtime callbacks in the driver.
>>
>> The OMAP remoteproc driver currently uses a default value of 10 seconds
>> for all OMAP remoteprocs, and a different value can be chosen either by
>> choosing a positive value for the 'autosuspend_delay' in the device's
>> omap_rproc_fw_data in the driver match data or by updating the
>> 'autosuspend_delay_ms' field at runtime through the sysfs interface.
>>      Eg: To use 25 seconds for IPU2 on DRA7xx,
>>        echo 25000 > /sys/bus/platform/devices/55020000.ipu/power/autosuspend_delay_ms
>>
>> The runtime suspend feature can also be similarly enabled or disabled by
>> writing 'auto' or 'on' to the device's 'control' power field. The default
>> is enabled.
>>      Eg: To disable auto-suspend for IPU2 on DRA7xx SoC,
>>        echo on > /sys/bus/platform/devices/55020000.ipu/power/control
>>
>> Signed-off-by: Suman Anna <s-anna@...com>
>> [t-kristo@...com: converted to use ti-sysc instead of hwmod]
>> Signed-off-by: Tero Kristo <t-kristo@...com>
>> ---
>>   drivers/remoteproc/omap_remoteproc.c | 220 ++++++++++++++++++++++++++-
>>   1 file changed, 214 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/remoteproc/omap_remoteproc.c b/drivers/remoteproc/omap_remoteproc.c
>> index 0a9b9f7d20da..463d6f60947a 100644
>> --- a/drivers/remoteproc/omap_remoteproc.c
>> +++ b/drivers/remoteproc/omap_remoteproc.c
>> @@ -20,6 +20,7 @@
>>   #include <linux/of_device.h>
>>   #include <linux/of_reserved_mem.h>
>>   #include <linux/platform_device.h>
>> +#include <linux/pm_runtime.h>
>>   #include <linux/dma-mapping.h>
>>   #include <linux/remoteproc.h>
>>   #include <linux/mailbox_client.h>
>> @@ -37,6 +38,9 @@
>>   #include "omap_remoteproc.h"
>>   #include "remoteproc_internal.h"
>>   
>> +/* default auto-suspend delay (ms) */
>> +#define DEFAULT_AUTOSUSPEND_DELAY		10000
>> +
>>   /**
>>    * struct omap_rproc_boot_data - boot data structure for the DSP omap rprocs
>>    * @syscon: regmap handle for the system control configuration module
>> @@ -83,6 +87,8 @@ struct omap_rproc_timer {
>>    * @num_mems: number of internal memory regions
>>    * @num_timers: number of rproc timer(s)
>>    * @timers: timer(s) info used by rproc
>> + * @autosuspend_delay: auto-suspend delay value to be used for runtime pm
>> + * @need_resume: if true a resume is needed in the system resume callback
>>    * @rproc: rproc handle
>>    * @reset: reset handle
>>    * @pm_comp: completion primitive to sync for suspend response
>> @@ -97,6 +103,8 @@ struct omap_rproc {
>>   	int num_mems;
>>   	int num_timers;
>>   	struct omap_rproc_timer *timers;
>> +	int autosuspend_delay;
>> +	bool need_resume;
>>   	struct rproc *rproc;
>>   	struct reset_control *reset;
>>   	struct completion pm_comp;
>> @@ -111,6 +119,7 @@ struct omap_rproc {
>>    * @boot_reg_shift: bit shift for the boot register mask
>>    * @mem_names: memory names for this remote processor
>>    * @dev_addrs: device addresses corresponding to the memory names
>> + * @autosuspend_delay: custom auto-suspend delay value in milliseconds
>>    */
>>   struct omap_rproc_dev_data {
>>   	const char *device_name;
>> @@ -118,6 +127,7 @@ struct omap_rproc_dev_data {
>>   	int boot_reg_shift;
>>   	const char * const *mem_names;
>>   	const u32 *dev_addrs;
>> +	int autosuspend_delay;
>>   };
>>   
>>   /**
>> @@ -384,11 +394,23 @@ static void omap_rproc_kick(struct rproc *rproc, int vqid)
>>   	struct device *dev = rproc->dev.parent;
>>   	int ret;
>>   
>> +	/* wake up the rproc before kicking it */
>> +	ret = pm_runtime_get_sync(dev);
>> +	if (WARN_ON(ret < 0)) {
>> +		dev_err(dev, "pm_runtime_get_sync() failed during kick, ret = %d\n",
>> +			ret);
>> +		pm_runtime_put_noidle(dev);
>> +		return;
>> +	}
>> +
>>   	/* send the index of the triggered virtqueue in the mailbox payload */
>>   	ret = mbox_send_message(oproc->mbox, (void *)vqid);
>>   	if (ret < 0)
>>   		dev_err(dev, "failed to send mailbox message, status = %d\n",
>>   			ret);
>> +
>> +	pm_runtime_mark_last_busy(dev);
>> +	pm_runtime_put_autosuspend(dev);
>>   }
>>   
>>   /**
>> @@ -473,6 +495,19 @@ static int omap_rproc_start(struct rproc *rproc)
>>   		goto put_mbox;
>>   	}
>>   
>> +	/*
>> +	 * remote processor is up, so update the runtime pm status and
>> +	 * enable the auto-suspend. The device usage count is incremented
>> +	 * manually for balancing it for auto-suspend
>> +	 */
>> +	pm_runtime_set_active(dev);
>> +	pm_runtime_set_autosuspend_delay(dev, oproc->autosuspend_delay);
>> +	pm_runtime_use_autosuspend(dev);
>> +	pm_runtime_get(dev);
>> +	pm_runtime_enable(dev);
>> +	pm_runtime_mark_last_busy(dev);
>> +	pm_runtime_put_autosuspend(dev);
>> +
>>   	reset_control_deassert(oproc->reset);
>>   
>>   	return 0;
>> @@ -485,9 +520,26 @@ static int omap_rproc_start(struct rproc *rproc)
>>   /* power off the remote processor */
>>   static int omap_rproc_stop(struct rproc *rproc)
>>   {
>> +	struct device *dev = rproc->dev.parent;
>>   	struct omap_rproc *oproc = rproc->priv;
>>   	int ret;
>>   
>> +	/*
>> +	 * cancel any possible scheduled runtime suspend by incrementing
>> +	 * the device usage count, and resuming the device. The remoteproc
>> +	 * also needs to be woken up if suspended, to avoid the remoteproc
>> +	 * OS to continue to remember any context that it has saved, and
>> +	 * avoid potential issues in misindentifying a subsequent device
>> +	 * reboot as a power restore boot
>> +	 */
>> +	ret = pm_runtime_get_sync(dev);
>> +	if (ret < 0) {
>> +		pm_runtime_put_noidle(dev);
>> +		return ret;
>> +	}
>> +
>> +	pm_runtime_put_sync(dev);
>> +
>>   	reset_control_assert(oproc->reset);
>>   
>>   	ret = omap_rproc_disable_timers(rproc, true);
>> @@ -496,6 +548,15 @@ static int omap_rproc_stop(struct rproc *rproc)
>>   
>>   	mbox_free_channel(oproc->mbox);
>>   
>> +	/*
>> +	 * update the runtime pm states and status now that the remoteproc
>> +	 * has stopped
>> +	 */
>> +	pm_runtime_disable(dev);
>> +	pm_runtime_dont_use_autosuspend(dev);
>> +	pm_runtime_put_noidle(dev);
>> +	pm_runtime_set_suspended(dev);
>> +
>>   	return 0;
>>   }
>>   
>> @@ -552,17 +613,19 @@ static bool _is_rproc_in_standby(struct omap_rproc *oproc)
>>   
>>   /* 1 sec is long enough time to let the remoteproc side suspend the device */
>>   #define DEF_SUSPEND_TIMEOUT 1000
>> -static int _omap_rproc_suspend(struct rproc *rproc)
>> +static int _omap_rproc_suspend(struct rproc *rproc, bool auto_suspend)
>>   {
>>   	struct device *dev = rproc->dev.parent;
>>   	struct omap_rproc *oproc = rproc->priv;
>>   	unsigned long to = msecs_to_jiffies(DEF_SUSPEND_TIMEOUT);
>>   	unsigned long ta = jiffies + to;
>> +	u32 suspend_msg = auto_suspend ?
>> +				RP_MBOX_SUSPEND_AUTO : RP_MBOX_SUSPEND_SYSTEM;
>>   	int ret;
>>   
>>   	reinit_completion(&oproc->pm_comp);
>>   	oproc->suspend_acked = false;
>> -	ret = mbox_send_message(oproc->mbox, (void *)RP_MBOX_SUSPEND_SYSTEM);
>> +	ret = mbox_send_message(oproc->mbox, (void *)suspend_msg);
>>   	if (ret < 0) {
>>   		dev_err(dev, "PM mbox_send_message failed: %d\n", ret);
>>   		return ret;
>> @@ -602,25 +665,55 @@ static int _omap_rproc_suspend(struct rproc *rproc)
>>   		goto enable_device;
>>   	}
>>   
>> +	/*
>> +	 * IOMMUs would have to be disabled specifically for runtime suspend.
>> +	 * They are handled automatically through System PM callbacks for
>> +	 * regular system suspend
>> +	 */
>> +	if (auto_suspend) {
>> +		ret = omap_iommu_domain_deactivate(rproc->domain);
>> +		if (ret) {
>> +			dev_err(dev, "iommu domain deactivate failed %d\n",
>> +				ret);
>> +			goto enable_timers;
>> +		}
>> +	}
>> +
>>   	return 0;
>> +enable_timers:
>> +	/* ignore errors on re-enabling code */
>> +	omap_rproc_enable_timers(rproc, false);
>>   
>>   enable_device:
>>   	reset_control_deassert(oproc->reset);
>>   	return ret;
>>   }
>>   
>> -static int _omap_rproc_resume(struct rproc *rproc)
>> +static int _omap_rproc_resume(struct rproc *rproc, bool auto_suspend)
>>   {
>>   	struct device *dev = rproc->dev.parent;
>>   	struct omap_rproc *oproc = rproc->priv;
>>   	int ret;
>>   
>> +	/*
>> +	 * IOMMUs would have to be enabled specifically for runtime resume.
>> +	 * They would have been already enabled automatically through System
>> +	 * PM callbacks for regular system resume
>> +	 */
>> +	if (auto_suspend) {
>> +		ret = omap_iommu_domain_activate(rproc->domain);
>> +		if (ret) {
>> +			dev_err(dev, "omap_iommu activate failed %d\n", ret);
>> +			goto out;
>> +		}
>> +	}
>> +
>>   	/* boot address could be lost after suspend, so restore it */
>>   	if (oproc->boot_data) {
>>   		ret = omap_rproc_write_dsp_boot_addr(rproc);
>>   		if (ret) {
>>   			dev_err(dev, "boot address restore failed %d\n", ret);
>> -			goto out;
>> +			goto suspend_iommu;
> 
> The same needs to be done if omap_rproc_enable_timers() fails.

Ok, will enhance the error handling logic a bit for v4.

> 
>>   		}
>>   	}
>>   
>> @@ -633,6 +726,12 @@ static int _omap_rproc_resume(struct rproc *rproc)
>>   
>>   	reset_control_deassert(oproc->reset);
>>   
>> +	return 0;
>> +
>> +suspend_iommu:
>> +	if (auto_suspend)
>> +		omap_iommu_domain_deactivate(rproc->domain);
>> +
>>   out:
>>   	return ret;
>>   }
>> @@ -641,6 +740,7 @@ static int __maybe_unused omap_rproc_suspend(struct device *dev)
>>   {
>>   	struct platform_device *pdev = to_platform_device(dev);
>>   	struct rproc *rproc = platform_get_drvdata(pdev);
>> +	struct omap_rproc *oproc = rproc->priv;
>>   	int ret = 0;
>>   
>>   	mutex_lock(&rproc->lock);
>> @@ -655,13 +755,25 @@ static int __maybe_unused omap_rproc_suspend(struct device *dev)
>>   		goto out;
>>   	}
>>   
>> -	ret = _omap_rproc_suspend(rproc);
>> +	ret = _omap_rproc_suspend(rproc, false);
>>   	if (ret) {
>>   		dev_err(dev, "suspend failed %d\n", ret);
>>   		goto out;
>>   	}
>>   
>> +	/*
>> +	 * remoteproc is running at the time of system suspend, so remember
>> +	 * it so as to wake it up during system resume
>> +	 */
>> +	oproc->need_resume = 1;
> 
> Please use 'true' to be consistent with the type and omap_rproc_resume().

Right.

> 
>>   	rproc->state = RPROC_SUSPENDED;
>> +
>> +	/*
>> +	 * update the runtime pm status to be suspended, without decrementing
>> +	 * the device usage count
>> +	 */
>> +	pm_runtime_disable(dev);
>> +	pm_runtime_set_suspended(dev);
>>   out:
>>   	mutex_unlock(&rproc->lock);
>>   	return ret;
>> @@ -671,6 +783,7 @@ static int __maybe_unused omap_rproc_resume(struct device *dev)
>>   {
>>   	struct platform_device *pdev = to_platform_device(dev);
>>   	struct rproc *rproc = platform_get_drvdata(pdev);
>> +	struct omap_rproc *oproc = rproc->priv;
>>   	int ret = 0;
>>   
>>   	mutex_lock(&rproc->lock);
>> @@ -682,17 +795,91 @@ static int __maybe_unused omap_rproc_resume(struct device *dev)
>>   		goto out;
>>   	}
>>   
>> -	ret = _omap_rproc_resume(rproc);
>> +	/*
>> +	 * remoteproc was auto-suspended at the time of system suspend,
>> +	 * so no need to wake-up the processor (leave it in suspended
>> +	 * state, will be woken up during a subsequent runtime_resume)
>> +	 */
>> +	if (!oproc->need_resume)
>> +		goto out;
>> +
>> +	ret = _omap_rproc_resume(rproc, false);
>>   	if (ret) {
>>   		dev_err(dev, "resume failed %d\n", ret);
>>   		goto out;
>>   	}
>> +	oproc->need_resume = false;
>>   
>>   	rproc->state = RPROC_RUNNING;
>> +
>> +	/*
>> +	 * update the runtime pm status to be active, without incrementing
>> +	 * the device usage count
>> +	 */
>> +	pm_runtime_set_active(dev);
>> +	pm_runtime_enable(dev);
>> +	pm_runtime_mark_last_busy(dev);
>>   out:
>>   	mutex_unlock(&rproc->lock);
>>   	return ret;
>>   }
>> +
>> +static int omap_rproc_runtime_suspend(struct device *dev)
>> +{
>> +	struct rproc *rproc = dev_get_drvdata(dev);
>> +	struct omap_rproc *oproc = rproc->priv;
>> +	int ret;
>> +
>> +	if (rproc->state == RPROC_CRASHED) {
>> +		dev_dbg(dev, "rproc cannot be runtime suspended when crashed!\n");
>> +		return -EBUSY;
>> +	}
>> +
>> +	if (WARN_ON(rproc->state != RPROC_RUNNING)) {
>> +		dev_err(dev, "rproc cannot be runtime suspended when not running!\n");
>> +		return -EBUSY;
>> +	}
>> +
>> +	/*
>> +	 * do not even attempt suspend if the remote processor is not
>> +	 * idled for runtime auto-suspend
>> +	 */
>> +	if (!_is_rproc_in_standby(oproc)) {
>> +		ret = -EBUSY;
>> +		goto abort;
>> +	}
>> +
>> +	ret = _omap_rproc_suspend(rproc, true);
>> +	if (ret)
>> +		goto abort;
>> +
>> +	rproc->state = RPROC_SUSPENDED;
>> +	return 0;
>> +
>> +abort:
>> +	pm_runtime_mark_last_busy(dev);
>> +	return ret;
>> +}
>> +
>> +static int omap_rproc_runtime_resume(struct device *dev)
>> +{
>> +	struct rproc *rproc = dev_get_drvdata(dev);
>> +	int ret;
>> +
>> +	if (WARN_ON(rproc->state != RPROC_SUSPENDED)) {
>> +		dev_err(dev, "rproc cannot be runtime resumed if not suspended!\n");
>> +		return -EBUSY;
>> +	}
>> +
>> +	ret = _omap_rproc_resume(rproc, true);
>> +	if (ret) {
>> +		dev_err(dev, "runtime resume failed %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	rproc->state = RPROC_RUNNING;
>> +	return 0;
>> +}
>>   #endif /* CONFIG_PM */
>>   
>>   static const char * const ipu_mem_names[] = {
>> @@ -778,6 +965,20 @@ static const struct of_device_id omap_rproc_of_match[] = {
>>   };
>>   MODULE_DEVICE_TABLE(of, omap_rproc_of_match);
>>   
>> +static int omap_rproc_get_autosuspend_delay(struct platform_device *pdev)
>> +{
>> +	const struct omap_rproc_dev_data *data;
>> +	int delay;
>> +
>> +	data = of_device_get_match_data(&pdev->dev);
>> +	if (!data)
>> +		return -ENODEV;
> 
> This check is done in omap_rproc_of_get_internal_memories() and
> omap_rproc_get_boot_data().  I think it would be best to do it once at the top
> of the probe() function and be done with it.
> 
> That being said and as noted in a previous comment, I would push all tuneables
> to the DT.  If the property is missing then things default to
> DEFAULT_AUTOSUSPEND_DELAY.

Ok, let me do that.

-Tero

> 
>> +
>> +	delay = data->autosuspend_delay;
>> +
>> +	return (delay > 0) ? delay : DEFAULT_AUTOSUSPEND_DELAY;
>> +}
>> +
>>   static const char *omap_rproc_get_firmware(struct platform_device *pdev)
>>   {
>>   	const char *fw_name;
>> @@ -953,6 +1154,11 @@ static int omap_rproc_probe(struct platform_device *pdev)
>>   	}
>>   
>>   	init_completion(&oproc->pm_comp);
>> +	oproc->autosuspend_delay = omap_rproc_get_autosuspend_delay(pdev);
>> +	if (oproc->autosuspend_delay < 0) {
>> +		ret = oproc->autosuspend_delay;
>> +		goto free_rproc;
>> +	}
>>   
>>   	oproc->fck = devm_clk_get(&pdev->dev, 0);
>>   	if (IS_ERR(oproc->fck)) {
>> @@ -994,6 +1200,8 @@ static int omap_rproc_remove(struct platform_device *pdev)
>>   
>>   static const struct dev_pm_ops omap_rproc_pm_ops = {
>>   	SET_SYSTEM_SLEEP_PM_OPS(omap_rproc_suspend, omap_rproc_resume)
>> +	SET_RUNTIME_PM_OPS(omap_rproc_runtime_suspend,
>> +			   omap_rproc_runtime_resume, NULL)
>>   };
>>   
>>   static struct platform_driver omap_rproc_driver = {
>> -- 
>> 2.17.1
>>
>> --

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

Powered by blists - more mailing lists