| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20220718113813.23787-2-hui.liu@mediatek.com>
Date: Mon, 18 Jul 2022 19:38:11 +0800
From: Hui Liu <hui.liu@...iatek.com>
To: <linus.walleij@...aro.org>, <robh+dt@...nel.org>,
<krzysztof.kozlowski+dt@...aro.org>, <matthias.bgg@...il.com>
CC: <srv_heupstream@...iatek.com>, <hui.liu@...iatek.com>,
<johnson.wang@...iatek.com>, <zhiyong.tao@...iatek.com>,
<sean.wang@...iatek.com>, <linux-gpio@...r.kernel.org>,
<devicetree@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>,
<linux-mediatek@...ts.infradead.org>,
<linux-kernel@...r.kernel.org>
Subject: [PATCH 1/3] dt-bindings: mediatek: add pinctrl definition for mt8188
From: "Hui.Liu" <hui.liu@...iatek.com>
This commit adds mt8188 compatible node in binding document.
Signed-off-by: Hui.Liu <hui.liu@...iatek.com>
---
.../bindings/pinctrl/pinctrl-mt8188.yaml | 306 ++++++++++++++++++
1 file changed, 306 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml
new file mode 100644
index 000000000000..43cc2424107f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml
@@ -0,0 +1,306 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8188.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MT8188 Pin Controller
+
+maintainers:
+ - Sean Wang <sean.wang@...iatek.com>
+
+description: |
+ The MediaTek's Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ const: mediatek,mt8188-pinctrl
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO binding is used,
+ the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+ const: 2
+
+ gpio-ranges:
+ description: gpio valid number range.
+ maxItems: 1
+
+ reg:
+ description: |
+ Physical address base for gpio base registers. There are 8 GPIO
+ physical address base in mt8188.
+ maxItems: 8
+
+ reg-names:
+ description: |
+ Gpio base register names.
+ maxItems: 8
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupts:
+ description: The interrupt outputs to sysirq.
+ maxItems: 1
+
+ mediatek,rsel_resistance_in_si_unit:
+ type: boolean
+ description: |
+ Identifying i2c pins pull up/down type which is RSEL. It can support
+ RSEL define or si unit value(ohm) to set different resistance.
+
+# PIN CONFIGURATION NODES
+patternProperties:
+ '-pins$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '^pins':
+ type: object
+ additionalProperties: false
+ description: |
+ A pinctrl node should contain at least one subnodes representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and
+ input schmitt.
+ An example of using macro:
+ pincontroller {
+ /* GPIO0 set as multifunction GPIO0 */
+ gpio-pins {
+ pins {
+ pinmux = <PINMUX_GPIO0__FUNC_B_GPIO0>;
+ }
+ };
+ /* GPIO56 set as multifunction SDA0 */
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
+ }
+ };
+ };
+ $ref: "pinmux-node.yaml"
+
+ properties:
+ pinmux:
+ description: |
+ Integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are
+ defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
+ directly.
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+
+ mediatek,drive-strength-adv:
+ description: |
+ Describe the specific driving setup property.
+ For I2C pins, the existing generic driving setup can only support
+ 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
+ can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
+ driving setup, the existing generic setup will be disabled.
+ The specific driving setup is controlled by E1E0EN.
+ When E1=0/E0=0, the strength is 0.125mA.
+ When E1=0/E0=1, the strength is 0.25mA.
+ When E1=1/E0=0, the strength is 0.5mA.
+ When E1=1/E0=1, the strength is 1mA.
+ EN is used to enable or disable the specific driving setup.
+ Valid arguments are described as below:
+ 0: (E1, E0, EN) = (0, 0, 0)
+ 1: (E1, E0, EN) = (0, 0, 1)
+ 2: (E1, E0, EN) = (0, 1, 0)
+ 3: (E1, E0, EN) = (0, 1, 1)
+ 4: (E1, E0, EN) = (1, 0, 0)
+ 5: (E1, E0, EN) = (1, 0, 1)
+ 6: (E1, E0, EN) = (1, 1, 0)
+ 7: (E1, E0, EN) = (1, 1, 1)
+ So the valid arguments are from 0 to 7.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ bias-pull-down:
+ oneOf:
+ - type: boolean
+ - enum: [100, 101, 102, 103]
+ description: mt8188 pull down PUPD/R0/R1 type define value.
+ - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+ description: mt8188 pull down RSEL type define value.
+ - enum: [75000, 5000]
+ description: mt8188 pull down RSEL type si unit value(ohm).
+ description: |
+ For pull down type is normal, it don't need add RSEL & R1R0 define
+ and resistance value.
+ For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
+ set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
+ "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
+ "MTK_PUPD_SET_R1R0_11" define in mt8188.
+ For pull down type is RSEL, it can add RSEL define & resistance
+ value(ohm) to set different resistance by identifying property
+ "mediatek,rsel_resistance_in_si_unit".
+ It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
+ & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
+ & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
+ & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
+ define in mt8188. It can also support resistance value(ohm)
+ "75000" & "5000" in mt8188.
+
+ An example of using RSEL define:
+ pincontroller {
+ i2c0_pin {
+ pins {
+ pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
+ bias-pull-updown = <MTK_PULL_SET_RSEL_001>;
+ }
+ };
+ };
+ An example of using si unit resistance value(ohm):
+ &pio {
+ mediatek,rsel_resistance_in_si_unit;
+ }
+ pincontroller {
+ i2c0_pin {
+ pins {
+ pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
+ bias-pull-down = <75000>;
+ }
+ };
+ };
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [100, 101, 102, 103]
+ description: mt8188 pull up PUPD/R0/R1 type define value.
+ - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+ description: mt8188 pull up RSEL type define value.
+ - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
+ description: mt8188 pull up RSEL type si unit value(ohm).
+ description: |
+ For pull up type is normal, it don't need add RSEL & R1R0 define
+ and resistance value.
+ For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
+ set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
+ "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
+ "MTK_PUPD_SET_R1R0_11" define in mt8188.
+ For pull up type is RSEL, it can add RSEL define & resistance
+ value(ohm) to set different resistance by identifying property
+ "mediatek,rsel_resistance_in_si_unit".
+ It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
+ & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
+ & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
+ & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
+ define in mt8188. It can also support resistance value(ohm)
+ "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" &
+ "75000" in mt8188.
+ An example of using RSEL define:
+ pincontroller {
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_001>;
+ }
+ };
+ };
+ An example of using si unit resistance value(ohm):
+ &pio {
+ mediatek,rsel_resistance_in_si_unit;
+ }
+ pincontroller {
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>;
+ bias-pull-up = <1000>;
+ }
+ };
+ };
+
+ bias-disable: true
+
+ output-high: true
+
+ output-low: true
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ required:
+ - pinmux
+
+allOf:
+ - $ref: "pinctrl.yaml#"
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/mt8188-pinfunc.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #
+ pio: pinctrl@...05000 {
+ compatible = "mediatek,mt8188-pinctrl";
+ reg = <0x10005000 0x1000>,
+ <0x11c00000 0x1000>,
+ <0x11e10000 0x1000>,
+ <0x11e20000 0x1000>,
+ <0x11ea0000 0x1000>,
+ <0x1000b000 0x1000>;
+ reg-names = "iocfg0", "iocfg_rm",
+ "iocfg_lt", "iocfg_lm", "iocfg_rt",
+ "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 176>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH 0>;
+ #interrupt-cells = <2>;
+
+ pio-pins {
+ pins {
+ pinmux = <PINMUX_GPIO0__FUNC_B_GPIO0>;
+ output-low;
+ };
+ };
+
+ spi0-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO75__FUNC_O_SPIM1_CSB>,
+ <PINMUX_GPIO76__FUNC_O_SPIM1_CLK>,
+ <PINMUX_GPIO77__FUNC_B0_SPIM1_MOSI>;
+ bias-disable;
+ };
+ pins-spi-mi {
+ pinmux = <PINMUX_GPIO78__FUNC_B0_SPIM1_MISO>;
+ bias-pull-down;
+ };
+ };
+
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO55__FUNC_B1_SCL0>,
+ <PINMUX_GPIO56__FUNC_B1_SDA0>;
+ bias-disable;
+ mediatek,drive-strength-adv = <7>;
+ };
+ };
+ };
--
2.18.0
Powered by blists - more mailing lists