[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <130bc9c5d5da94b25e2ee456039b1818225f7bef.camel@nxp.com>
Date: Mon, 15 Aug 2022 10:55:58 +0800
From: Liu Ying <victor.liu@....com>
To: Rob Herring <robh@...nel.org>
Cc: gregkh@...uxfoundation.org, linux-arm-kernel@...ts.infradead.org,
kernel@...gutronix.de, festevam@...il.com,
krzysztof.kozlowski@...aro.org, saravanak@...gle.com,
geert+renesas@...der.be, robh+dt@...nel.org,
s.hauer@...gutronix.de, linux-imx@....com,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
shawnguo@...nel.org, krzysztof.kozlowski+dt@...aro.org
Subject: Re: [PATCH v4 2/2] dt-bindings: bus: Add Freescale i.MX8qxp pixel
link MSI bus binding
On Sun, 2022-08-14 at 12:35 -0600, Rob Herring wrote:
> On Sun, 14 Aug 2022 15:43:38 +0800, Liu Ying wrote:
> > Freescale i.MX8qxp pixel link MSI bus is a simple memory-mapped
> > bus.
> > It is used to access peripherals in i.MX8qm/qxp imaging, LVDS, MIPI
> > DSI and HDMI TX subsystems, like I2C controller, PWM controller,
> > MIPI DSI controller and Control and Status Registers (CSR) module.
> >
> > Reference simple-pm-bus bindings and add Freescale i.MX8qxp pixel
> > link MSI bus specific bindings.
> >
> > Signed-off-by: Liu Ying <victor.liu@....com>
> > ---
> > v3->v4:
> > * Add child nodes in the example MSI bus node of the MSI bus dt-
> > binding. (Krzysztof)
> >
> > v2->v3:
> > * Add a pattern property to allow child nodes. (Rob)
> >
> > v1->v2:
> > Address Krzysztof's comments:
> > * Add a select to explicitly select the MSI bus dt-binding.
> > * List 'simple-pm-bus' explicitly as one item of compatible
> > strings.
> > * Require compatible and reg properties.
> > * Put reg property just after compatible property in example.
> >
> > .../bus/fsl,imx8qxp-pixel-link-msi-bus.yaml | 232
> > ++++++++++++++++++
> > 1 file changed, 232 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/bus/fsl,imx8qxp-pixel-link-msi-
> > bus.yaml
> >
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m
> dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> Documentation/devicetree/bindings/bus/fsl,imx8qxp-pixel-link-msi-
> bus.example.dtb:0:0: /example-0/bus@...00000/syscon@...21000: failed
> to match any schema with compatible: ['fsl,imx8qxp-mipi-lvds-csr',
> 'syscon', 'simple-mfd']
> Documentation/devicetree/bindings/bus/fsl,imx8qxp-pixel-link-msi-
> bus.example.dtb:0:0: /example-0/bus@...00000/syscon@...21000/pxl2dpi:
> failed to match any schema with compatible: ['fsl,imx8qxp-pxl2dpi']
> Documentation/devicetree/bindings/bus/fsl,imx8qxp-pixel-link-msi-
> bus.example.dtb:0:0: /example-0/bus@...00000/syscon@...21000/ldb:
> failed to match any schema with compatible: ['fsl,imx8qxp-ldb']
I sent this a bit earlier than v6.0-rc1. Now, v6.0-rc1 is out and there
is no error if the base is v6.0-rc1.
>
> doc reference errors (make refcheckdocs):
>
> See https://patchwork.ozlabs.org/patch/
>
> This check can fail if there are any dependencies. The base for a
> patch
> series is generally the most recent rc1.
Yes, there are dependencies if the base is v5.19-rc1.
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up
> to
> date:
>
> pip3 install dtschema --upgrade
>
> Please check and re-submit.
Do I need to re-submit? Or, you may run "make DT_CHECKER_FLAGS=-m
dt_binding_check" upon v6.0-rc1?
Regards,
Liu Ying
Powered by blists - more mailing lists