lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <9d6841f3-e3d5-a875-8057-1727f7ccaf1e@ti.com>
Date:   Wed, 11 Jan 2023 23:48:57 +0530
From:   "Raghavendra, Vignesh" <vigneshr@...com>
To:     Sjoerd Simons <sjoerd@...labora.com>, Nishanth Menon <nm@...com>
CC:     <kernel@...labora.com>, Nitin Yadav <n-yadav@...com>,
        <martyn.welch@...labora.com>,
        Aswath Govindraju <a-govindraju@...com>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Rob Herring <robh+dt@...nel.org>,
        Tero Kristo <kristo@...nel.org>, <devicetree@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>,
        <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v3 3/3] arm64: dts: ti: k3-am625-sk: Add support for USB

Hi Sjoerd,

Couple of comments which I failed to notice on v2, sorry

On 1/11/2023 6:53 PM, Sjoerd Simons wrote:
> From: Aswath Govindraju <a-govindraju@...com>
> 
> AM62 SoC has two instances of USB and they are brought on to the board
> in the following way,
> 
> -> USB0 instance
>  - This is brought out to a USB TypeC connector on board through TPS6598 PD
>    controller. The PD controller should decide the role based on CC pin in
>    the connector. Unfortunately the irq line for the TPS isn't hooked up
>    which is a mode not yet support by the driver (some patches were
>    submitted earlier this year[0]). So for now the PD controller is left
>    out and periphal mode chosen.

s/periphal/peripheral

> 
> -> USB1 instance
>  - This is brought out to a USB TypeA connector on board.
> 
> Therefore, add the required device tree support for the above in the board
> dts file.
> 
> 0: https://lore.kernel.org/lkml/f714ee55-ef47-317d-81b9-57020dda064b@ti.com/T/
> 
> Signed-off-by: Aswath Govindraju <a-govindraju@...com>
> Signed-off-by: Vignesh Raghavendra <vigneshr@...com>
> [merge from vendor bsp, drop TPS6598 support, reword commit message]
> Signed-off-by: Sjoerd Simons <sjoerd@...labora.com>
> Tested-by: Martyn Welch <martyn.welch@...labora.com>
> 
> ---
> 
> Changes in v3:
> - Rebased against current ti-next aka 6.2-rc1
> - Add Martyn's tested-by
> 
> Changes in v2:
> - Rebase against linux-next 20221220
> 
>  arch/arm64/boot/dts/ti/k3-am625-sk.dts | 50 ++++++++++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 

[...]

> +
> +&ecap0 {
> +	status = "disabled";
> +};
> +
> +&ecap1 {
> +	status = "disabled";
> +};
> +
> +&ecap2 {
> +	status = "disabled";
> +};
> +
> +&main_mcan0 {
> +	status = "disabled";
> +};
> +
> +&epwm0 {
> +	status = "disabled";
> +};
> +
> +&epwm1 {
> +	status = "disabled";
> +};
> +
> +&epwm2 {
> +	status = "disabled";
> +};
> +

Unlike downstream vendor kernel, these nodes are "disabled" by default
in k3-am62-main.dtsi. So, these can be dropped.

> +&usbss0 {
> +	ti,vbus-divider;
> +};
> +
> +&usb0 {
> +	dr_mode = "peripheral";
> +};
> +
> +&usb1 {
> +	dr_mode = "host";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_usb1_pins_default>;
> +};

Regards
Vignesh

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ