linux-kernel - Re: [PATCH v4 6/7] arm64: dts: ti: k3-j722s-main: Add SERDES and PCIe support

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <4c29a5d9-d7ec-4175-b726-c41e2711ac0f@ti.com>
Date: Tue, 4 Jun 2024 10:51:36 +0530
From: Siddharth Vadapalli <s-vadapalli@...com>
To: Andrew Davis <afd@...com>
CC: Siddharth Vadapalli <s-vadapalli@...com>, <nm@...com>, <vigneshr@...com>,
        <kristo@...nel.org>, <robh@...nel.org>, <krzk+dt@...nel.org>,
        <conor+dt@...nel.org>, <rogerq@...nel.org>,
        <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
        <linux-arm-kernel@...ts.infradead.org>, <u-kumar1@...com>,
        <danishanwar@...com>, <srk@...com>
Subject: Re: [PATCH v4 6/7] arm64: dts: ti: k3-j722s-main: Add SERDES and
 PCIe support

On Mon, Jun 03, 2024 at 09:17:43AM -0500, Andrew Davis wrote:
> On 6/1/24 7:15 AM, Siddharth Vadapalli wrote:
> > J722S SoC has two instances of SERDES namely SERDES0 and SERDES1 and one
> > instance of PCIe namely PCIe0. Both SERDES0 and SERDES1 are single lane
> > SERDES. The PCIe0 instance of PCIe is a Gen3 single lane PCIe controller.
> > 

[...]

> > +
> > +		serdes0: serdes@...0000 {
> > +			compatible = "ti,j721e-serdes-10g";
> > +			reg = <0x0f000000 0x00010000>;
> > +			reg-names = "torrent_phy";
> > +			resets = <&serdes_wiz0 0>;
> > +			reset-names = "torrent_reset";
> > +			clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
> > +				 <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>;
> > +			clock-names = "refclk", "phy_en_refclk";
> > +			assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
> > +					  <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>,
> > +					  <&serdes_wiz0 TI_WIZ_REFCLK_DIG>;
> > +			assigned-clock-parents = <&k3_clks 279 1>,
> > +						 <&k3_clks 279 1>,
> > +						 <&k3_clks 279 1>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			#clock-cells = <1>;
> > +
> > +			status = "disabled"; /* Needs lane config */
> 
> Does the other SERDES (serdes1) not need this config? It looks like
> it does in the board file.. If so disable it too.

The "lane config" being referred to here is set by the "serdes_ln_ctrl"
mux. The idle-states being set in the board file match the reset values
of the mux, so it is not technically necessary to disable it. However, I
will go ahead and disable SERDES1 as well and enable it in the board file
in the v5 series. Thank you for the review.

[...]

Regards,
Siddharth.