Message-ID: <4D24DC58.7090009@grandegger.com>
Date:	Wed, 05 Jan 2011 22:02:16 +0100
From:	Wolfgang Grandegger <wg@...ndegger.com>
To:	Kurt Van Dijck <kurt.van.dijck@....be>
CC:	netdev@...r.kernel.org, socketcan-core@...ts.berlios.de
Subject: Re: [PATCH net-next-2.6 v2 2/2] can: add driver for Softing card

On 01/04/2011 04:09 PM, Kurt Van Dijck wrote:
> This patch adds the driver that creates a platform:softing device
> from a pcmcia_device
> Note: the Kconfig indicates a dependency on the softing.ko driver,
> but this is purely to make configuration intuitive. This driver will
> work independent, but no CAN network devices appear until softing.ko is
> loaded too.
> 
> Signed-off-by: Kurt Van Dijck <kurt.van.dijck@....be>
> 
> ---
>  drivers/net/can/softing/Kconfig      |   13 ++
>  drivers/net/can/softing/Makefile     |    1 +
>  drivers/net/can/softing/softing_cs.c |  361 ++++++++++++++++++++++++++++++++++
>  3 files changed, 375 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/net/can/softing/Kconfig b/drivers/net/can/softing/Kconfig
> index 072f337..14ebe14 100644
> --- a/drivers/net/can/softing/Kconfig
> +++ b/drivers/net/can/softing/Kconfig
> @@ -14,3 +14,16 @@ config CAN_SOFTING
>  	  controls the 2 busses on the card together.
>  	  As such, some actions (start/stop/busoff recovery) on 1 bus
>  	  must bring down the other bus too temporarily.
> +
> +config CAN_SOFTING_CS
> +	tristate "Softing CAN pcmcia cards"
> +	depends on PCMCIA

Does it not also depend on CAN_SOFTING?

> +	---help---
> +	  Support for PCMCIA cards from Softing Gmbh & some cards
> +	  from Vector Gmbh.
> +	  You need firmware for these, which you can get at
> +	  http://developer.berlios.de/projects/socketcan/
> +	  This version of the driver is written against
> +	  firmware version 4.6 (softing-fw-4.6-binaries.tar.gz)
> +	  In order to use the card as CAN device, you need the Softing generic
> +	  support too.
> diff --git a/drivers/net/can/softing/Makefile b/drivers/net/can/softing/Makefile
> index 7878b7b..5f0f527 100644
> --- a/drivers/net/can/softing/Makefile
> +++ b/drivers/net/can/softing/Makefile
> @@ -1,5 +1,6 @@
>  
>  softing-y := softing_main.o softing_fw.o
>  obj-$(CONFIG_CAN_SOFTING)        += softing.o
> +obj-$(CONFIG_CAN_SOFTING_CS)     += softing_cs.o
>  
>  ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG
> diff --git a/drivers/net/can/softing/softing_cs.c b/drivers/net/can/softing/softing_cs.c
> new file mode 100644
> index 0000000..cffd4d1
> --- /dev/null
> +++ b/drivers/net/can/softing/softing_cs.c
> @@ -0,0 +1,361 @@
> +/*
> + * drivers/net/can/softing/softing_cs.c

Please remove reduntant information, here and in other files.

> + *
> + * Copyright (C) 2008-2010
> + *
> + * - Kurt Van Dijck, EIA Electronics
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the version 2 of the GNU General Public License
> + * as published by the Free Software Foundation
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
> + */
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +
> +#include <pcmcia/cistpl.h>
> +#include <pcmcia/ds.h>
> +
> +#include "softing_platform.h"
> +
> +static int softingcs_index;
> +static spinlock_t softingcs_index_lock;
> +
> +static int softingcs_reset(struct platform_device *pdev, int v);
> +static int softingcs_enable_irq(struct platform_device *pdev, int v);
> +
> +/*
> + * platform_data descriptions
> + */
> +static const struct softing_platform_data softingcs_platform_data[] = {
> +{
> +	.name = "CANcard",
> +	.manf = 0x0168, .prod = 0x001,
> +	.generation = 1,
> +	.nbus = 2,
> +	.freq = 16, .max_brp = 32, .max_sjw = 4,
> +	.dpram_size = 0x0800,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = softingcs_enable_irq,
> +}, {
> +	.name = "CANcard-NEC",
> +	.manf = 0x0168, .prod = 0x002,
> +	.generation = 1,
> +	.nbus = 2,
> +	.freq = 16, .max_brp = 32, .max_sjw = 4,
> +	.dpram_size = 0x0800,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = softingcs_enable_irq,
> +}, {
> +	.name = "CANcard-SJA",
> +	.manf = 0x0168, .prod = 0x004,
> +	.generation = 1,
> +	.nbus = 2,
> +	.freq = 20, .max_brp = 32, .max_sjw = 4,
> +	.dpram_size = 0x0800,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cansja.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = softingcs_enable_irq,
> +}, {
> +	.name = "CANcard-2",
> +	.manf = 0x0168, .prod = 0x005,
> +	.generation = 2,
> +	.nbus = 2,
> +	.freq = 24, .max_brp = 64, .max_sjw = 4,
> +	.dpram_size = 0x1000,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard2.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard2.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cancrd2.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = 0,
> +}, {
> +	.name = "Vector-CANcard",
> +	.manf = 0x0168, .prod = 0x081,
> +	.generation = 1,
> +	.nbus = 2,
> +	.freq = 16, .max_brp = 64, .max_sjw = 4,
> +	.dpram_size = 0x0800,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = softingcs_enable_irq,
> +}, {
> +	.name = "Vector-CANcard-SJA",
> +	.manf = 0x0168, .prod = 0x084,
> +	.generation = 1,
> +	.nbus = 2,
> +	.freq = 20, .max_brp = 32, .max_sjw = 4,
> +	.dpram_size = 0x0800,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cansja.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = softingcs_enable_irq,
> +}, {
> +	.name = "Vector-CANcard-2",
> +	.manf = 0x0168, .prod = 0x085,
> +	.generation = 2,
> +	.nbus = 2,
> +	.freq = 24, .max_brp = 64, .max_sjw = 4,
> +	.dpram_size = 0x1000,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard2.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard2.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cancrd2.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = 0,
> +}, {
> +	.name = "EDICcard-NEC",
> +	.manf = 0x0168, .prod = 0x102,
> +	.generation = 1,
> +	.nbus = 2,
> +	.freq = 16, .max_brp = 64, .max_sjw = 4,
> +	.dpram_size = 0x0800,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cancard.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = softingcs_enable_irq,
> +}, {
> +	.name = "EDICcard-2",
> +	.manf = 0x0168, .prod = 0x105,
> +	.generation = 2,
> +	.nbus = 2,
> +	.freq = 24, .max_brp = 64, .max_sjw = 4,
> +	.dpram_size = 0x1000,
> +	.boot = {0x0000, 0x000000, fw_dir "bcard2.bin",},
> +	.load = {0x0120, 0x00f600, fw_dir "ldcard2.bin",},
> +	.app = {0x0010, 0x0d0000, fw_dir "cancrd2.bin",},
> +	.reset = softingcs_reset,
> +	.enable_irq = 0,
> +}, {
> +	0, 0,
> +},
> +};
> +
> +MODULE_FIRMWARE(fw_dir "bcard.bin");
> +MODULE_FIRMWARE(fw_dir "ldcard.bin");
> +MODULE_FIRMWARE(fw_dir "cancard.bin");
> +MODULE_FIRMWARE(fw_dir "cansja.bin");
> +
> +MODULE_FIRMWARE(fw_dir "bcard2.bin");
> +MODULE_FIRMWARE(fw_dir "ldcard2.bin");
> +MODULE_FIRMWARE(fw_dir "cancrd2.bin");
> +
> +static const struct softing_platform_data *softingcs_find_platform_data(
> +		unsigned int manf, unsigned int prod)
> +{
> +	const struct softing_platform_data *lp;
> +
> +	for (lp = softingcs_platform_data; lp->manf; ++lp) {
> +		if ((lp->manf == manf) && (lp->prod == prod))
> +			return lp;
> +	}
> +	return 0;
> +}
> +
> +/*
> + * platformdata callbacks
> + */
> +static int softingcs_reset(struct platform_device *pdev, int v)
> +{
> +	struct pcmcia_device *pcmcia = to_pcmcia_dev(pdev->dev.parent);
> +
> +	dev_dbg(&pdev->dev, "pcmcia config [2] %02x\n", v ? 0 : 0x20);
> +	return pcmcia_write_config_byte(pcmcia, 2, v ? 0 : 0x20);
> +}
> +
> +static int softingcs_enable_irq(struct platform_device *pdev, int v)
> +{
> +	struct pcmcia_device *pcmcia = to_pcmcia_dev(pdev->dev.parent);
> +
> +	dev_dbg(&pdev->dev, "pcmcia config [0] %02x\n", v ? 0x60 : 0);
> +	return pcmcia_write_config_byte(pcmcia, 0, v ? 0x60 : 0);
> +}
> +
> +/*
> + * pcmcia check
> + */
> +static int softingcs_probe_config(struct pcmcia_device *pcmcia,
> +		void *priv_data)
> +{
> +	struct softing_platform_data *pdat = priv_data;
> +	struct resource *pres;
> +	int memspeed = 0;
> +
> +	WARN_ON(!pdat);
> +	pres = pcmcia->resource[PCMCIA_IOMEM_0];
> +	if (resource_size(pres) < 0x1000)
> +		return -ERANGE;
> +
> +	pres->flags |= WIN_MEMORY_TYPE_CM | WIN_ENABLE;
> +	if (pdat->generation < 2) {
> +		pres->flags |= WIN_USE_WAIT | WIN_DATA_WIDTH_8;
> +		memspeed = 3;
> +	} else {
> +		pres->flags |= WIN_DATA_WIDTH_16;
> +	}
> +	return pcmcia_request_window(pcmcia, pres, memspeed);
> +}
> +
> +static void softingcs_remove(struct pcmcia_device *pcmcia)
> +{
> +	struct platform_device *pdev = pcmcia->priv;
> +
> +	/* free bits */
> +	platform_device_unregister(pdev);
> +	/* release pcmcia stuff */
> +	pcmcia_disable_device(pcmcia);
> +}
> +
> +/*
> + * platform_device wrapper
> + * pdev->resource has 2 entries: io & irq
> + */
> +static void softingcs_pdev_release(struct device *dev)
> +{
> +	struct platform_device *pdev = to_platform_device(dev);
> +	kfree(pdev);
> +}
> +
> +static int softingcs_probe(struct pcmcia_device *pcmcia)
> +{
> +	int ret;
> +	struct platform_device *pdev;
> +	const struct softing_platform_data *pdat;
> +	struct resource *pres;
> +	struct dev {
> +		struct platform_device pdev;
> +		struct resource res[2];
> +	} *dev;
> +
> +	/* find matching platform_data */
> +	pdat = softingcs_find_platform_data(pcmcia->manf_id, pcmcia->card_id);
> +	if (!pdat)
> +		return -ENOTTY;
> +
> +	/* setup pcmcia device */
> +	pcmcia->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IOMEM |
> +		CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC;
> +	ret = pcmcia_loop_config(pcmcia, softingcs_probe_config, (void *)pdat);
> +	if (ret)
> +		goto pcmcia_failed;
> +
> +	ret = pcmcia_enable_device(pcmcia);
> +	if (ret < 0)
> +		goto pcmcia_failed;
> +
> +	pres = pcmcia->resource[PCMCIA_IOMEM_0];
> +	if (!pres) {
> +		ret = -EBADF;
> +		goto pcmcia_bad;
> +	}
> +
> +	/* create softing platform device */
> +	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
> +	if (!dev) {
> +		ret = -ENOMEM;
> +		goto mem_failed;
> +	}
> +	dev->pdev.resource = dev->res;
> +	dev->pdev.num_resources = ARRAY_SIZE(dev->res);
> +	dev->pdev.dev.release = softingcs_pdev_release;
> +
> +	pdev = &dev->pdev;
> +	pdev->dev.platform_data = (void *)pdat;
> +	pdev->dev.parent = &pcmcia->dev;
> +	pcmcia->priv = pdev;
> +
> +	/* platform device resources */
> +	pdev->resource[0].flags = IORESOURCE_MEM;
> +	pdev->resource[0].start = pres->start;
> +	pdev->resource[0].end = pres->end;
> +
> +	pdev->resource[1].flags = IORESOURCE_IRQ;
> +	pdev->resource[1].start = pcmcia->irq;
> +	pdev->resource[1].end = pdev->resource[1].start;
> +
> +	/* platform device setup */
> +	spin_lock(&softingcs_index_lock);
> +	pdev->id = softingcs_index++;
> +	spin_unlock(&softingcs_index_lock);
> +	pdev->name = "softing";
> +	dev_set_name(&pdev->dev, "softingcs.%i", pdev->id);
> +	ret = platform_device_register(pdev);
> +	if (ret < 0)
> +		goto platform_failed;
> +
> +	dev_info(&pcmcia->dev, "created %s\n", dev_name(&pdev->dev));
> +	return 0;
> +
> +platform_failed:
> +	kfree(dev);
> +mem_failed:
> +pcmcia_bad:
> +pcmcia_failed:
> +	pcmcia_disable_device(pcmcia);
> +	pcmcia->priv = 0;
> +	return ret ?: -ENODEV;
> +}
> +
> +static /*const*/ struct pcmcia_device_id softingcs_ids[] = {
> +	/* softing */
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0001),
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0002),
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0004),
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0005),
> +	/* vector, manufacturer? */
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0081),
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0084),
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0085),
> +	/* EDIC */
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0102),
> +	PCMCIA_DEVICE_MANF_CARD(0x0168, 0x0105),
> +	PCMCIA_DEVICE_NULL,
> +};
> +
> +MODULE_DEVICE_TABLE(pcmcia, softingcs_ids);
> +
> +static struct pcmcia_driver softingcs_driver = {
> +	.owner		= THIS_MODULE,
> +	.name		= "softingcs",
> +	.id_table	= softingcs_ids,
> +	.probe		= softingcs_probe,
> +	.remove		= softingcs_remove,
> +};

Also here, I'm missing the usage of __devinit and friends.

> +static int __init softingcs_start(void)
> +{
> +	spin_lock_init(&softingcs_index_lock);
> +	return pcmcia_register_driver(&softingcs_driver);
> +}
> +
> +static void __exit softingcs_stop(void)
> +{
> +	pcmcia_unregister_driver(&softingcs_driver);
> +}
> +
> +module_init(softingcs_start);
> +module_exit(softingcs_stop);
> +
> +MODULE_DESCRIPTION("softing CANcard driver"
> +		", links PCMCIA card to softing driver");
> +MODULE_LICENSE("GPL");

GPL v2 ?

Thanks for your contribution.

Wolfgang.
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Powered by blists - more mailing lists