| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <da349ea7-e12f-4749-8c54-604f65780d9e@loongson.cn>
Date: Sat, 20 Apr 2024 19:02:26 +0800
From: Yanteng Si <siyanteng@...ngson.cn>
To: Serge Semin <fancer.lancer@...il.com>
Cc: andrew@...n.ch, hkallweit1@...il.com, peppe.cavallaro@...com,
alexandre.torgue@...s.st.com, joabreu@...opsys.com, Jose.Abreu@...opsys.com,
chenhuacai@...nel.org, linux@...linux.org.uk, guyinggang@...ngson.cn,
netdev@...r.kernel.org, chris.chenfeiyang@...il.com, siyanteng01@...il.com
Subject: Re: [PATCH net-next v11 6/6] net: stmmac: dwmac-loongson: Add
Loongson GNET support
在 2024/4/18 22:01, Serge Semin 写道:
> On Fri, Apr 12, 2024 at 07:28:51PM +0800, Yanteng Si wrote:
>> There are two types of Loongson DWGMAC. The first type shares the same
>> register definitions and has similar logic as dwmac1000. The second type
>> uses several different register definitions, we think it is necessary to
>> distinguish rx and tx, so we split these bits into two.
>>
>> Simply put, we split some single bit fields into double bits fileds:
>>
>> Name Tx Rx
>>
>> DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000;
>> DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000;
>> DMA_STATUS_NIS = 0x00040000 | 0x00020000;
>> DMA_STATUS_AIS = 0x00010000 | 0x00008000;
>> DMA_STATUS_FBI = 0x00002000 | 0x00001000;
>>
>> Therefore, when using, TX and RX must be set at the same time.
>>
>> How to use them:
>> 1. Create the Loongson GNET-specific
>> stmmac_dma_ops.dma_interrupt()
>> stmmac_dma_ops.init_chan()
>> methods in the dwmac-loongson.c driver. Adding all the
>> Loongson-specific macros
>>
>> 2. Create a Loongson GNET-specific platform setup method with the next
>> semantics:
>> + allocate stmmac_dma_ops instance and initialize it with
>> dwmac1000_dma_ops.
>> + override the stmmac_dma_ops.{dma_interrupt, init_chan} with
>> the pointers to the methods defined in 2.
>> + allocate mac_device_info instance and initialize the
>> mac_device_info.dma field with a pointer to the new
>> stmmac_dma_ops instance.
>> + initialize mac_device_info in a way it's done in
>> dwmac1000_setup().
>>
>> 3. Initialize plat_stmmacenet_data.setup() with the pointer to the
>> method created in 2.
>>
>> GNET features:
>>
>> Speeds: 10/100/1000Mbps
>> DMA-descriptors type: normal and enhanced
> Hm, it's either one or another. They can't be both supported because
> the alternative descriptors are enabled by the DESC_ENHANCED_FORMAT
> HDL parameter defined on the IP-core synthesize stage.
Sorry, It is enhanced.
>
>> L3/L4 filters availability: support
>> VLAN hash table filter: support
>> PHY-interface: GMII
>> Remote Wake-up support: support
>> Mac Management Counters (MMC): support
>> DMA chennel number: 0x10 device is 8 and 0x37 device is 1
> What about adding the info like:
> Number of additional MAC addresses
> MAC Hash-based filter support and if supported the hash table size.
It is OK.
Number of additional MAC addresses: 5
MAC Hash-based filter: support
Number of ash table size: 256
>> **Note**: Currently, only the LS2K2000's IP core is 0x10,
> This doesn't sound correct. The LS2K2000's IP-core is v3.73a. But the
> SNPS Version ID was manually altered by the hardware designers.
Hmm, Our original intention was to express the reality of the hardware,
How about:
**Note**: Currently, only the LS2K2000's synopsys_id is 0x10, while the
synopsys_id of other devices are 0x37.
>
>> while the IP
>> cores of other devices are 0x37.
> Real IP-core ID isn't described by the hex number. It's a digit number
> like v3.73a/v3.50a/etc. Hex number you constantly repeat is the
> MAC_Version.SNPSVER register value. So please use the IP-core version
> in the v3.xx format all over the patch text.
In this context, using synopsys_id is more accurate.
>
>> Signed-off-by: Feiyang Chen <chenfeiyang@...ngson.cn>
>> Signed-off-by: Yinggang Gu <guyinggang@...ngson.cn>
>> Signed-off-by: Yanteng Si <siyanteng@...ngson.cn>
>> ---
>> drivers/net/ethernet/stmicro/stmmac/common.h | 2 +
>> .../ethernet/stmicro/stmmac/dwmac-loongson.c | 476 ++++++++++++++++--
>> .../ethernet/stmicro/stmmac/dwmac1000_dma.c | 1 +
>> .../ethernet/stmicro/stmmac/stmmac_ethtool.c | 6 +
>> include/linux/stmmac.h | 1 +
>> 5 files changed, 447 insertions(+), 39 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h
>> index 9cd62b2110a1..6777dc997e9f 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/common.h
>> +++ b/drivers/net/ethernet/stmicro/stmmac/common.h
>> @@ -29,6 +29,7 @@
>> /* Synopsys Core versions */
>> #define DWMAC_CORE_3_40 0x34
>> #define DWMAC_CORE_3_50 0x35
>> +#define DWMAC_CORE_3_70 0x37
>> #define DWMAC_CORE_4_00 0x40
>> #define DWMAC_CORE_4_10 0x41
>> #define DWMAC_CORE_5_00 0x50
>> @@ -258,6 +259,7 @@ struct stmmac_safety_stats {
>> #define CSR_F_300M 300000000
>>
>> #define MAC_CSR_H_FRQ_MASK 0x20
>> +#define MAC_CTRL_PORT_SELECT_10_100 BIT(15)
> No, this is already defined in:
> drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
> as GMAC_CONTROL_PS macros. Use it instead of adding new macros.
Okay, let's call it.
>
>>
>> #define HASH_TABLE_SIZE 64
>> #define PAUSE_TIME 0xffff
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
>> index 69078eb1f923..4edfbb4fcb64 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
>> @@ -8,8 +8,70 @@
>> #include <linux/device.h>
>> #include <linux/of_irq.h>
>> #include "stmmac.h"
>> +#include "dwmac_dma.h"
>> +#include "dwmac1000.h"
>> +
>> +/* Normal Loongson Tx Summary */
>> +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000
>> +/* Normal Loongson Rx Summary */
>> +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000
>> +
>> +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \
>> + DMA_INTR_ENA_NIE_RX_LOONGSON | \
>> + DMA_INTR_ENA_RIE | DMA_INTR_ENA_TIE)
>> +
>> +/* Abnormal Loongson Tx Summary */
>> +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000
>> +/* Abnormal Loongson Rx Summary */
>> +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000
>> +
>> +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \
>> + DMA_INTR_ENA_AIE_RX_LOONGSON | \
>> + DMA_INTR_ENA_FBE | DMA_INTR_ENA_UNE)
>> +
>> +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | \
>> + DMA_INTR_ABNORMAL_LOONGSON)
>> +
>> +/* Normal Loongson Tx Interrupt Summary */
>> +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000
>> +/* Normal Loongson Rx Interrupt Summary */
>> +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000
>> +
>> +/* Abnormal Loongson Tx Interrupt Summary */
>> +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000
>> +/* Abnormal Loongson Rx Interrupt Summary */
>> +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000
>> +
>> +/* Fatal Loongson Tx Bus Error Interrupt */
>> +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000
>> +/* Fatal Loongson Rx Bus Error Interrupt */
>> +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000
>> +
>> +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \
>> + DMA_STATUS_NIS_RX_LOONGSON | \
>> + DMA_STATUS_AIS_TX_LOONGSON | \
>> + DMA_STATUS_AIS_RX_LOONGSON | \
>> + DMA_STATUS_FBI_TX_LOONGSON | \
>> + DMA_STATUS_FBI_RX_LOONGSON)
>> +
>> +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | DMA_STATUS_RWT | \
>> + DMA_STATUS_RPS | DMA_STATUS_RU | \
>> + DMA_STATUS_RI | DMA_STATUS_OVF | \
>> + DMA_STATUS_MSK_COMMON_LOONGSON)
>> +
>> +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | DMA_STATUS_UNF | \
>> + DMA_STATUS_TJT | DMA_STATUS_TU | \
>> + DMA_STATUS_TPS | DMA_STATUS_TI | \
>> + DMA_STATUS_MSK_COMMON_LOONGSON)
>>
>> #define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03
>> +#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13
>> +#define LOONGSON_DWMAC_CORE_1_00 0x10 /* Loongson custom IP */
>> +#define CHANNEL_NUM 8
>> +
>> +struct loongson_data {
>> + struct device *dev;
>> +};
>>
>> struct stmmac_pci_info {
>> int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data *plat);
>> @@ -56,6 +117,8 @@ static int loongson_gmac_data(struct pci_dev *pdev,
>> plat->dma_cfg->pblx8 = true;
>>
>> plat->multicast_filter_bins = 256;
>> + plat->mdio_bus_data->phy_mask = 0;
>> +
> And this change isn't related to the GNET. Why is it here?
OK, move this into a preparation/pre-requisite patch
>
>> plat->clk_ref_rate = 125000000;
>> plat->clk_ptp_rate = 125000000;
>>
>> @@ -69,13 +132,342 @@ static struct stmmac_pci_info loongson_gmac_pci_info = {
>> .setup = loongson_gmac_data,
>> };
>>
>> -static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>> +static void loongson_gnet_dma_init_channel(struct stmmac_priv *priv,
>> + void __iomem *ioaddr,
>> + struct stmmac_dma_cfg *dma_cfg,
>> + u32 chan)
>> +{
>> + int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl;
>> + int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl;
>> + u32 value;
>> +
>> + /* common channel control register config */
> Useless comment. Please drop.
Ok.
>
>> + value = readl(ioaddr + DMA_CHAN_BUS_MODE(chan));
>> +
>> + /* Set the DMA PBL (Programmable Burst Length) mode.
>> + *
>> + * Note: before stmmac core 3.50 this mode bit was 4xPBL, and
>> + * post 3.5 mode bit acts as 8*PBL.
>> + */
> Do you have an IP-core older than v3.50a? No. So please drop the
> comment.
I will drop it.
>
>> + if (dma_cfg->pblx8)
>> + value |= DMA_BUS_MODE_MAXPBL;
>> +
>> + value |= DMA_BUS_MODE_USP;
>> + value &= ~(DMA_BUS_MODE_PBL_MASK | DMA_BUS_MODE_RPBL_MASK);
>> + value |= (txpbl << DMA_BUS_MODE_PBL_SHIFT);
>> + value |= (rxpbl << DMA_BUS_MODE_RPBL_SHIFT);
>> +
>> + /* Set the Fixed burst mode */
>> + if (dma_cfg->fixed_burst)
>> + value |= DMA_BUS_MODE_FB;
>> +
>> + /* Mixed Burst has no effect when fb is set */
>> + if (dma_cfg->mixed_burst)
>> + value |= DMA_BUS_MODE_MB;
>> +
>> + if (dma_cfg->atds)
>> + value |= DMA_BUS_MODE_ATDS;
>> +
>> + if (dma_cfg->aal)
>> + value |= DMA_BUS_MODE_AAL;
>> +
>> + writel(value, ioaddr + DMA_CHAN_BUS_MODE(chan));
>> +
>> + /* Mask interrupts by writing to CSR7 */
>> + writel(DMA_INTR_DEFAULT_MASK_LOONGSON, ioaddr +
>> + DMA_CHAN_INTR_ENA(chan));
>> +}
>> +
>> +static int loongson_gnet_dma_interrupt(struct stmmac_priv *priv,
>> + void __iomem *ioaddr,
>> + struct stmmac_extra_stats *x,
>> + u32 chan, u32 dir)
>> +{
>> + struct stmmac_pcpu_stats *stats = this_cpu_ptr(priv->xstats.pcpu_stats);
>> + u32 abnor_intr_status;
>> + u32 nor_intr_status;
>> + u32 fb_intr_status;
>> + u32 intr_status;
>> + int ret = 0;
>> +
>> + /* read the status register (CSR5) */
>> + intr_status = readl(ioaddr + DMA_CHAN_STATUS(chan));
>> +
>> + if (dir == DMA_DIR_RX)
>> + intr_status &= DMA_STATUS_MSK_RX_LOONGSON;
>> + else if (dir == DMA_DIR_TX)
>> + intr_status &= DMA_STATUS_MSK_TX_LOONGSON;
>> +
>> + nor_intr_status = intr_status & (DMA_STATUS_NIS_TX_LOONGSON |
>> + DMA_STATUS_NIS_RX_LOONGSON);
>> + abnor_intr_status = intr_status & (DMA_STATUS_AIS_TX_LOONGSON |
>> + DMA_STATUS_AIS_RX_LOONGSON);
>> + fb_intr_status = intr_status & (DMA_STATUS_FBI_TX_LOONGSON |
>> + DMA_STATUS_FBI_RX_LOONGSON);
>> +
>> + /* ABNORMAL interrupts */
>> + if (unlikely(abnor_intr_status)) {
>> + if (unlikely(intr_status & DMA_STATUS_UNF)) {
>> + ret = tx_hard_error_bump_tc;
>> + x->tx_undeflow_irq++;
>> + }
>> + if (unlikely(intr_status & DMA_STATUS_TJT))
>> + x->tx_jabber_irq++;
>> + if (unlikely(intr_status & DMA_STATUS_OVF))
>> + x->rx_overflow_irq++;
>> + if (unlikely(intr_status & DMA_STATUS_RU))
>> + x->rx_buf_unav_irq++;
>> + if (unlikely(intr_status & DMA_STATUS_RPS))
>> + x->rx_process_stopped_irq++;
>> + if (unlikely(intr_status & DMA_STATUS_RWT))
>> + x->rx_watchdog_irq++;
>> + if (unlikely(intr_status & DMA_STATUS_ETI))
>> + x->tx_early_irq++;
>> + if (unlikely(intr_status & DMA_STATUS_TPS)) {
>> + x->tx_process_stopped_irq++;
>> + ret = tx_hard_error;
>> + }
>> + if (unlikely(fb_intr_status)) {
>> + x->fatal_bus_error_irq++;
>> + ret = tx_hard_error;
>> + }
>> + }
>> + /* TX/RX NORMAL interrupts */
>> + if (likely(nor_intr_status)) {
>> + if (likely(intr_status & DMA_STATUS_RI)) {
>> + u32 value = readl(ioaddr + DMA_INTR_ENA);
>> + /* to schedule NAPI on real RIE event. */
>> + if (likely(value & DMA_INTR_ENA_RIE)) {
>> + u64_stats_update_begin(&stats->syncp);
>> + u64_stats_inc(&stats->rx_normal_irq_n[chan]);
>> + u64_stats_update_end(&stats->syncp);
>> + ret |= handle_rx;
>> + }
>> + }
>> + if (likely(intr_status & DMA_STATUS_TI)) {
>> + u64_stats_update_begin(&stats->syncp);
>> + u64_stats_inc(&stats->tx_normal_irq_n[chan]);
>> + u64_stats_update_end(&stats->syncp);
>> + ret |= handle_tx;
>> + }
>> + if (unlikely(intr_status & DMA_STATUS_ERI))
>> + x->rx_early_irq++;
>> + }
>> + /* Optional hardware blocks, interrupts should be disabled */
>> + if (unlikely(intr_status &
>> + (DMA_STATUS_GPI | DMA_STATUS_GMI | DMA_STATUS_GLI)))
>> + pr_warn("%s: unexpected status %08x\n", __func__, intr_status);
>> +
>> + /* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */
>> + writel((intr_status & 0x7ffff), ioaddr + DMA_CHAN_STATUS(chan));
>> +
>> + return ret;
>> +}
>> +
>> +static void loongson_gnet_fix_speed(void *priv, unsigned int speed,
>> + unsigned int mode)
>> +{
>> + struct loongson_data *ld = (struct loongson_data *)priv;
>> + struct net_device *ndev = dev_get_drvdata(ld->dev);
>> + struct stmmac_priv *ptr = netdev_priv(ndev);
>> +
>> + /* The controller and PHY don't work well together.
>> + * We need to use the PS bit to check if the controller's status
>> + * is correct and reset PHY if necessary.
>> + * MAC_CTRL_REG.15 is defined by the GMAC_CONTROL_PS macro.
>> + */
>> + if (speed == SPEED_1000) {
>> + if (readl(ptr->ioaddr + MAC_CTRL_REG) &
>> + MAC_CTRL_PORT_SELECT_10_100)
> GMAC_CONTROL_PS?
Yeah!
>> + /* Word around hardware bug, restart autoneg */
>> + phy_restart_aneg(ndev->phydev);
>> + }
>> +}
>> +
>> +static int loongson_gnet_data(struct pci_dev *pdev,
>> + struct plat_stmmacenet_data *plat)
>> +{
>> + loongson_default_data(pdev, plat);
>> +
>> + plat->phy_addr = -1;
>> + plat->phy_interface = PHY_INTERFACE_MODE_GMII;
>> +
>> + plat->dma_cfg->pbl = 32;
>> + plat->dma_cfg->pblx8 = true;
>> +
>> + plat->multicast_filter_bins = 256;
>> + plat->mdio_bus_data->phy_mask = ~(u32)BIT(2);
>> +
>> + plat->clk_ref_rate = 125000000;
>> + plat->clk_ptp_rate = 125000000;
> If this is common for both GMAC and GNET what about moving it to the
> loongson_default_data() method?
>
> If so please just do that in the patch 4 where you get to add these
> fields initialization in the first place.
Okay!
>
>> +
>> + plat->fix_mac_speed = loongson_gnet_fix_speed;
>> +
>> + return 0;
>> +}
>> +
>> +static struct stmmac_pci_info loongson_gnet_pci_info = {
>> + .setup = loongson_gnet_data,
>> +};
>> +
>> +static int loongson_dwmac_config_legacy(struct pci_dev *pdev,
>> + struct plat_stmmacenet_data *plat,
>> + struct stmmac_resources *res,
>> + struct device_node *np)
>> +{
>> + if (np) {
>> + res->irq = of_irq_get_byname(np, "macirq");
>> + if (res->irq < 0) {
>> + dev_err(&pdev->dev, "IRQ macirq not found\n");
>> + return -ENODEV;
>> + }
>> +
>> + res->wol_irq = of_irq_get_byname(np, "eth_wake_irq");
>> + if (res->wol_irq < 0) {
>> + dev_info(&pdev->dev,
>> + "IRQ eth_wake_irq not found, using macirq\n");
>> + res->wol_irq = res->irq;
>> + }
>> +
>> + res->lpi_irq = of_irq_get_byname(np, "eth_lpi");
>> + if (res->lpi_irq < 0) {
>> + dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
>> + return -ENODEV;
>> + }
>> + } else {
>> + res->irq = pdev->irq;
>> + res->wol_irq = res->irq;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int loongson_dwmac_config_msi(struct pci_dev *pdev,
>> + struct plat_stmmacenet_data *plat,
>> + struct stmmac_resources *res,
>> + struct device_node *np)
>> +{
>> + int i, ret, vecs;
>> +
>> + vecs = roundup_pow_of_two(CHANNEL_NUM * 2 + 1);
>> + ret = pci_alloc_irq_vectors(pdev, vecs, vecs, PCI_IRQ_MSI);
>> + if (ret < 0) {
>> + dev_info(&pdev->dev,
>> + "MSI enable failed, Fallback to legacy interrupt\n");
>> + return loongson_dwmac_config_legacy(pdev, plat, res, np);
>> + }
>> +
>> + res->irq = pci_irq_vector(pdev, 0);
>> + res->wol_irq = 0;
>> +
>> + /* INT NAME | MAC | CH7 rx | CH7 tx | ... | CH0 rx | CH0 tx |
>> + * --------- ----- -------- -------- ... -------- --------
>> + * IRQ NUM | 0 | 1 | 2 | ... | 15 | 16 |
>> + */
>> + for (i = 0; i < CHANNEL_NUM; i++) {
>> + res->rx_irq[CHANNEL_NUM - 1 - i] =
>> + pci_irq_vector(pdev, 1 + i * 2);
>> + res->tx_irq[CHANNEL_NUM - 1 - i] =
>> + pci_irq_vector(pdev, 2 + i * 2);
>> + }
>> +
>> + plat->flags |= STMMAC_FLAG_MULTI_MSI_EN;
> Once again. Please replace this with simpler solution:
>
> static int loongson_dwmac_config_multi_msi(struct pci_dev *pdev,
> + struct plat_stmmacenet_data *plat,
> + struct stmmac_resources *res)
> +{
> + int i, ret, vecs;
> +
> + /* INT NAME | MAC | CH7 rx | CH7 tx | ... | CH0 rx | CH0 tx |
> + * --------- ----- -------- -------- ... -------- --------
> + * IRQ NUM | 0 | 1 | 2 | ... | 15 | 16 |
> + */
> + vecs = plat->rx_queues_to_use + plat->tx_queues_to_use + 1;
> + ret = pci_alloc_irq_vectors(pdev, 1, vecs, PCI_IRQ_MSI | PCI_IRQ_LEGACY);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "Failed to allocate PCI IRQs\n");
> + return ret;
> + } else if (ret >= vecs) {
> + for (i = 0; i < plat->rx_queues_to_use; i++) {
> + res->rx_irq[CHANNELS_NUM - 1 - i] =
> + pci_irq_vector(pdev, 1 + i * 2);
> + }
> + for (i = 0; i < plat->tx_queues_to_use; i++) {
> + res->tx_irq[CHANNELS_NUM - 1 - i] =
> + pci_irq_vector(pdev, 2 + i * 2);
> + }
> +
> + plat->flags |= STMMAC_FLAG_MULTI_MSI_EN;
> + }
> +
> + res->irq = pci_irq_vector(pdev, 0);
> +
> + return 0;
> +}
Well, I'll try again.
>
>> +
>> + return 0;
>> +}
>> +
>> +static struct mac_device_info *loongson_dwmac_setup(void *apriv)
>> +{
>> + struct stmmac_priv *priv = apriv;
>> + struct stmmac_resources res;
>> + struct mac_device_info *mac;
>> + struct stmmac_dma_ops *dma;
>> + struct pci_dev *pdev;
>> + u32 loongson_gmac;
>> +
>> + memset(&res, 0, sizeof(res));
>> + pdev = to_pci_dev(priv->device);
>> + res.addr = pcim_iomap_table(pdev)[0];
>> + loongson_gmac = readl(res.addr + GMAC_VERSION) & 0xff;
>> +
>> + mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL);
>> + if (!mac)
>> + return NULL;
>> +
>> + dma = devm_kzalloc(priv->device, sizeof(*dma), GFP_KERNEL);
>> + if (!dma)
>> + return NULL;
>> +
>> + /* The original IP-core version is 0x37 in all Loongson GNET
>> + * (ls2k2000 and ls7a2000), but the GNET HW designers have changed the
>> + * GMAC_VERSION.SNPSVER field to the custom 0x10 value on the Loongson
>> + * ls2k2000 MAC to emphasize the differences: multiple DMA-channels,
>> + * AV feature and GMAC_INT_STATUS CSR flags layout. Get back the
>> + * original value so the correct HW-interface would be selected.
>> + */
>> + if (loongson_gmac == LOONGSON_DWMAC_CORE_1_00) {
>> + priv->synopsys_id = DWMAC_CORE_3_70;
>> + *dma = dwmac1000_dma_ops;
>> + dma->init_chan = loongson_gnet_dma_init_channel;
>> + dma->dma_interrupt = loongson_gnet_dma_interrupt;
>> + mac->dma = dma;
>> + }
>> +
>> + mac->mac = &dwmac1000_ops;
>> + priv->dev->priv_flags |= IFF_UNICAST_FLT;
>> +
>> + /* Pre-initialize the respective "mac" fields as it's done in
>> + * dwmac1000_setup()
>> + */
>> + mac->pcsr = priv->ioaddr;
>> + mac->multicast_filter_bins = priv->plat->multicast_filter_bins;
>> + mac->unicast_filter_entries = priv->plat->unicast_filter_entries;
>> + mac->mcast_bits_log2 = 0;
>> +
>> + if (mac->multicast_filter_bins)
>> + mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins);
>> +
>> + /* The GMAC devices with PCI ID 0x7a03 does not support any pause mode.
>> + * The GNET devices without CORE ID 0x10 does not support half-duplex.
>> + */
>> + if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC) {
>> + mac->link.caps = MAC_10 | MAC_100 | MAC_1000;
>> + } else {
>> + if (loongson_gmac == LOONGSON_DWMAC_CORE_1_00)
>> + mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
>> + MAC_10 | MAC_100 | MAC_1000;
>> + else
>> + mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
>> + MAC_10FD | MAC_100FD | MAC_1000FD;
>> + }
>> +
>> + mac->link.duplex = GMAC_CONTROL_DM;
>> + mac->link.speed10 = GMAC_CONTROL_PS;
>> + mac->link.speed100 = GMAC_CONTROL_PS | GMAC_CONTROL_FES;
>> + mac->link.speed1000 = 0;
>> + mac->link.speed_mask = GMAC_CONTROL_PS | GMAC_CONTROL_FES;
>> + mac->mii.addr = GMAC_MII_ADDR;
>> + mac->mii.data = GMAC_MII_DATA;
>> + mac->mii.addr_shift = 11;
>> + mac->mii.addr_mask = 0x0000F800;
>> + mac->mii.reg_shift = 6;
>> + mac->mii.reg_mask = 0x000007C0;
>> + mac->mii.clk_csr_shift = 2;
>> + mac->mii.clk_csr_mask = GENMASK(5, 2);
>> +
>> + return mac;
>> +}
>> +
>> +static int loongson_dwmac_probe(struct pci_dev *pdev,
>> + const struct pci_device_id *id)
>> {
>> struct plat_stmmacenet_data *plat;
>> int ret, i, bus_id, phy_mode;
>> struct stmmac_pci_info *info;
>> struct stmmac_resources res;
>> + struct loongson_data *ld;
>> struct device_node *np;
>> + u32 loongson_gmac;
>>
>> plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
>> if (!plat)
>> @@ -88,10 +482,14 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
>> return -ENOMEM;
>>
>> plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*plat->dma_cfg), GFP_KERNEL);
>> - if (!plat->dma_cfg) {
>> - ret = -ENOMEM;
>> - goto err_put_node;
>> - }
>> + if (!plat->dma_cfg)
>> + return -ENOMEM;
>> +
>> + ld = devm_kzalloc(&pdev->dev, sizeof(*ld), GFP_KERNEL);
>> + if (!ld)
>> + return -ENOMEM;
>> +
>> + np = dev_of_node(&pdev->dev);
> Here is the missing np from the patch 5...
Yeah, I will merge it to patch 5.
>
>>
>> /* Enable pci device */
>> ret = pci_enable_device(pdev);
>> @@ -110,14 +508,6 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
>> break;
>> }
>>
>> - phy_mode = device_get_phy_mode(&pdev->dev);
>> - if (phy_mode < 0) {
>> - dev_err(&pdev->dev, "phy_mode not found\n");
>> - ret = phy_mode;
>> - goto err_disable_device;
>> - }
>> -
>> - plat->phy_interface = phy_mode;
> This change must have been added to the Patch 5 where you get to move
> all the NP-related things into the "if (np) {}" clause!
Sorry, this part is in patch 5.
>
>> plat->mac_interface = PHY_INTERFACE_MODE_GMII;
>>
>> pci_set_master(pdev);
>> @@ -133,7 +523,6 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
>> dev_info(&pdev->dev, "Found MDIO subnode\n");
>> plat->mdio_bus_data->needs_reset = true;
>> }
>> -
>> bus_id = of_alias_get_id(np, "ethernet");
>> if (bus_id >= 0)
>> plat->bus_id = bus_id;
>> @@ -145,42 +534,49 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
>> goto err_disable_device;
>> }
>> plat->phy_interface = phy_mode;
>> + }
>>
>> - res.irq = of_irq_get_byname(np, "macirq");
>> - if (res.irq < 0) {
>> - dev_err(&pdev->dev, "IRQ macirq not found\n");
>> - ret = -ENODEV;
>> - goto err_disable_msi;
>> - }
>> + plat->bsp_priv = ld;
>> + plat->setup = loongson_dwmac_setup;
>> + ld->dev = &pdev->dev;
>>
>> - res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
>> - if (res.wol_irq < 0) {
>> - dev_info(&pdev->dev, "IRQ eth_wake_irq not found, using macirq\n");
>> - res.wol_irq = res.irq;
>> - }
>> + memset(&res, 0, sizeof(res));
>> + res.addr = pcim_iomap_table(pdev)[0];
>> + loongson_gmac = readl(res.addr + GMAC_VERSION) & 0xff;
>>
>> - res.lpi_irq = of_irq_get_byname(np, "eth_lpi");
>> - if (res.lpi_irq < 0) {
>> - dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
>> - ret = -ENODEV;
>> - goto err_disable_msi;
>> - }
>> - } else {
>> - res.irq = pdev->irq;
> Please, move the loongson_dwmac_config_legacy() method creation change
> into a preparation/pre-requisite patch. That will vastly simplify this
> patch and will help with reviewing it!
Okay!
>
>> + switch (loongson_gmac) {
>> + case LOONGSON_DWMAC_CORE_1_00:
>> + plat->rx_queues_to_use = CHANNEL_NUM;
>> + plat->tx_queues_to_use = CHANNEL_NUM;
>> +
>> + /* Only channel 0 supports checksum,
>> + * so turn off checksum to enable multiple channels.
>> + */
>> + for (i = 1; i < CHANNEL_NUM; i++)
>> + plat->tx_queues_cfg[i].coe_unsupported = 1;
>> +
>> + ret = loongson_dwmac_config_msi(pdev, plat, &res, np);
>> + break;
>> + default: /* 0x35 device and 0x37 device. */
>> + plat->tx_queues_to_use = 1;
>> + plat->rx_queues_to_use = 1;
>> + ret = loongson_dwmac_config_legacy(pdev, plat, &res, np);
>> + break;
>> }
>>
>> - pci_enable_msi(pdev);
>> - memset(&res, 0, sizeof(res));
>> - res.addr = pcim_iomap_table(pdev)[0];
>> + /* GNET devices with dev revision 0x00 do not support manually
>> + * setting the speed to 1000.
>> + */
>> + if (pdev->device == PCI_DEVICE_ID_LOONGSON_GNET &&
>> + pdev->revision == 0x00)
>> + plat->flags |= STMMAC_FLAG_DISABLE_FORCE_1000;
> Move this to the loongson_gnet_data() method.
Okay, But I noticed your comment at the end that we need to splite as a
separate _pre-requisite/preparation_ patch, this fix is for gnet devices, there is no gnet at this time. So, if I
understand you correctly, we should need two patches: net: stmmac:
dwmac-loongson: Disable force 1000 net: stmmac: dwmac-loongson: Add
Loongson GNET support net: stmmac: dwmac-loongson: Move DISABLE_FORCE_1000 flag to loongson_gnet_data() method
>
>>
>> ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
>> if (ret)
>> - goto err_disable_msi;
>> + goto err_disable_device;
>>
>> return ret;
>>
>> -err_disable_msi:
>> - pci_disable_msi(pdev);
>> err_disable_device:
>> pci_disable_device(pdev);
>> err_put_node:
>> @@ -248,6 +644,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
>>
>> static const struct pci_device_id loongson_dwmac_id_table[] = {
>> { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) },
>> + { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) },
>> {}
>> };
>> MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);
>> @@ -266,4 +663,5 @@ module_pci_driver(loongson_dwmac_driver);
>>
>> MODULE_DESCRIPTION("Loongson DWMAC PCI driver");
>> MODULE_AUTHOR("Qing Zhang <zhangqing@...ngson.cn>");
>> +MODULE_AUTHOR("Yanteng Si <siyanteng@...ngson.cn>");
>> MODULE_LICENSE("GPL v2");
> Please move this into a separate patch. It can be the last patch in
> the series.
Okay.
>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
>> index f161ec9ac490..66c0c22908b1 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
>> @@ -296,3 +296,4 @@ const struct stmmac_dma_ops dwmac1000_dma_ops = {
>> .get_hw_feature = dwmac1000_get_hw_feature,
>> .rx_watchdog = dwmac1000_rx_watchdog,
>> };
>> +EXPORT_SYMBOL_GPL(dwmac1000_dma_ops);
>
> Please move this into a preparation/pre-requisite patch.
Okay.
>
>
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
>> index e1537a57815f..e94faa72f30e 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
>> @@ -420,6 +420,12 @@ stmmac_ethtool_set_link_ksettings(struct net_device *dev,
>> return 0;
>> }
>>
>> + if (priv->plat->flags & STMMAC_FLAG_DISABLE_FORCE_1000) {
>> + if (cmd->base.speed == SPEED_1000 &&
>> + cmd->base.autoneg != AUTONEG_ENABLE)
>> + return -EOPNOTSUPP;
>> + }
>> +
>> return phylink_ethtool_ksettings_set(priv->phylink, cmd);
>> }
>>
>> diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
>> index 1b54b84a6785..c5d3d0ddb6f8 100644
>> --- a/include/linux/stmmac.h
>> +++ b/include/linux/stmmac.h
>> @@ -223,6 +223,7 @@ struct dwmac4_addrs {
>> #define STMMAC_FLAG_RX_CLK_RUNS_IN_LPI BIT(10)
>> #define STMMAC_FLAG_EN_TX_LPI_CLOCKGATING BIT(11)
>> #define STMMAC_FLAG_HWTSTAMP_CORRECT_LATENCY BIT(12)
>> +#define STMMAC_FLAG_DISABLE_FORCE_1000 BIT(13)
>>
>> struct plat_stmmacenet_data {
>> int bus_id;
> Please move this in a separate _pre-requisite/preparation_ patch.
> Really. Why have you merged it into this one? This patch already got
> to be too complicated. Don't make it even more complex.
Ok, I'll split them again.
>
> ---
>
> I look at v8 and look at v9 series. Why have you re-shuffled the
> change so significantly??? It has made my life in reviewing your bits
> much harder because instead of checking whether you took my v8-notes
> into account I had to once again analyze the entire series. Sigh...
Sorry to put the pressure on you.
I think it is because there ware so many changes to the v8, and I take a
long
time to get through all the comments. I'll try to shorten it in the future.
This version of the comments I can do easily, except
loongson_dwmac_config_multi_msi(),
and once I get it done, I will send v12. (Maybe next Monday? I hope so.)
Thanks,
Yanteng
Powered by blists - more mailing lists